Benutzeranleitung / Produktwartung e2050 des Produzenten Toro
Zur Seite of 120
Part No. 04127S L (Rev . D) Service Manual W orkman R e2050 & e2065 Preface The pur pose of this public ation is to pr ovide t he service technic ian with inf orm ation f or t roubles hooting, test ing and repair of maj or syst ems and co mponents on the Workman e2050 and e2065.
Workman e2050/e2065 This page is intentionally blank..
Workman e2050/e2065 T able Of Contents Chapter 1 – Safety Safety Instructions 1 – 2 . . . . . . . . . . . . . . . . . . . . . . . . . . Jacking and Other Instructions 1 – 4 . . . . . . . . . . . . . . . Safety and Instruction Decals 1 – 5 . . .
Workman e2050/e2065 This page is intentionally blank..
Workman e2050/e2065 Page 1 – 1 Safety (Rev . B) Chapter 1 Safety T able of Contents SAFETY INSTRUCTIONS 2 . . . . . . . . . . . . . . . . . . . . . . Before Operating 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . While Operating 2 . . . .
Rev . D W orkman e2050/e2065 Page 1 - - 2 Safety (Rev . B) Safety Instructions The Workman e2050 and e2065 are designed and tested to offer safe service when operated and main- tained properly .
Workman e2050/e2065 Page 1 – 3 Safety (Rev . B) Maintenance and Service 1. Before servicing or making adjustments to the ve- hicle, stop vehicle, turn on/off switch to OFF , engage parking brake and remove key from the on/off switch. 2. Make sure machine is in safe operating condition by keeping all nuts, bolts and screws tight.
Workman e2050/e2065 Page 1 – 4 Safety (Rev . B) Jacking and Other Instructions Jacking V ehicle DANGER POTENTIAL HAZARD • A vehicle that is not properly supported may become unstable. WHA T CAN HAPPEN • The vehicle may move or fall. Personal injury or damage to the machine may result.
Workman e2050/e2065 Page 1 – 5 Safety (Rev . B) Safety and Instruction Decals There are several safety and instruction decals attached to your W orkman vehicle. If any decal becomes illegible or damaged, install a new decal. Part numbers are listed in the Parts Catalog.
Workman e2050/e2065 Page 1 – 6 Safety (Rev . B) This page is intentionally blank..
Workman e2050/e2065 Page 2 – 1 Product Records and Maintenance (Rev . B) Chapter 2 Product Records and Maintenance T able of Contents PRODUCT RECORDS 1 . . . . . . . . . . . . . . . . . . . . . . . . . EQUIV ALENTS AND CONVERSIONS 2 . . . . . . . . .
0.09375 Workman e2050/e2065 Page 2 – 2 Product Records and Maintenance (Rev . B) Equivalents and Conversions.
Workman e2050/e2065 Page 2 – 3 Product Records and Maintenance (Rev . B) T orque Specifications Recommended fastener torque values are listed in the following tables.
Workman e2050/e2065 Page 2 – 4 Product Records and Maintenance (Rev . B) Standard T orque for Dry , Zinc Plated and Steel Fasteners (Inch Series) Thread Size Grade 1, 5, & 8 with Thin Height Nut.
Workman e2050/e2065 Page 2 – 5 Product Records and Maintenance (Rev . B) Standard T orque for Dry , Zinc Plated and Steel Fasteners (Metric Fasteners) Thread Size Class 8.
Workman e2050/e2065 Page 2 – 6 Product Records and Maintenance (Rev . B) Other T orque Specifications SAE Grade 8 Steel Set Screws Thread Size Recommended T orque Thread Size Square Head Hex Socket .
Workman e2050/e2065 Page 2 – 7 Product Records and Maintenance (Rev . B) Maintenance Maintenance procedures and recommended service in- tervals for the Workman e2050 and e2065 are covered in the Operator ’s Manual. Refer to that publication when performing regular vehicle maintenance.
Workman e2050/e2065 Page 2 – 8 Product Records and Maintenance (Rev . B) This page is intentionally blank..
Workman e2050/e2065 Page 3 – 1 Electrical System (Rev . B) Chapter 3 Electrical System T able of Contents ELECTRICAL DIAGRAMS 2 . . . . . . . . . . . . . . . . . . . . . GENERAL INFORMA TION 3 . . . . . . . . . . . . . . . . . . . . . Opening Battery Circuit 3 .
Workman e2050/e2065 Page 3 – 2 Electrical System (Rev . B) Electrical Diagrams The electrical schematic, circuit drawings and wire har- ness drawings for the Workman e2050 and e2065 are located in Chapter 6 – Electrical Diagrams.
Workman e2050/e2065 Page 3 – 3 Electrical System (Rev . B) General Information The W orkman e2050 and e2065 use a 48 volt DC elec- trical system that is an isolated circuit. The vehicle frame is not used for any ground connections. The vehicle controller monitors operator and vehicle in- puts to determine voltage to the traction motor .
Workman e2050/e2065 Page 3 – 4 Electrical System (Rev . B) V ehicle Operation The Workman e2050 and e2065 electrical system use a 48 volt battery pack, an electric traction motor , a ve- hicle controller and numerous other electrical compo- nents to allow vehicle operation.
Workman e2050/e2065 Page 3 – 5 Electrical System (Rev . B) Special T ools Multimeter The multimeter can test electrical components and cir- cuits for current, resistance or voltage. NOTE: T oro recommends the use of a DIGIT AL V olt– Ohm–Amp multimeter when testing electrical circuits.
Workman e2050/e2065 Page 3 – 6 Electrical System (Rev . B) Battery W atering Dispenser Use the battery watering dispenser when adding dis- tilled water to vehicle batteries. Obtain watering dis- penser locally . Figure 6 Battery Hydrometer Use the battery hydrometer when measuring specific gravity of battery electrolyte.
Rev . D Workman e2050/e2065 Page 3 - - 7 Electrical System (Rev . B) 36/48 V olt Battery Discharge Unit The 36/48 V olt Battery Discharge Unit (TOR4106) is rec- ommended for quick and accurate load testing for the batteries on the Workman e2050 and e2065.
Workman e2050/e2065 Page 3 – 8 Electrical System (Rev . B) T roubleshooting CAUTION Remove all jewelry , especially rings and watches, before doing any electrical trouble- shooting or testing. Disconnect a battery cable from the battery pack to open the battery circuit unless a test procedure requires battery voltage.
Workman e2050/e2065 Page 3 – 9 Electrical System (Rev . B) General Run Problems (Continued) Problem Possible Causes T raction motor stops during operation. Wiring to the traction motor components (e.g. main contactor , controller , traction motor) loose, corroded or damaged (see Electrical Schematic in Chapter 6 – Electrical Diagrams).
Workman e2050/e2065 Page 3 – 10 Electrical System (Rev . B) Battery Charger Problems Problem Possible Causes Battery charger does not turn on. AC outlet fuse/circuit breaker blown. AC outlet is faulty . V ehicle wiring is loose or damaged (see electrical schematic in Chapter 6 – Electrical Diagrams).
Workman e2050/e2065 Page 3 – 1 1 Electrical System (Rev . B) Adjustments Accelerator Switch Adjustment 1. Position vehicle on a level surface, turn On/Of f switch OFF and remove key . Apply parking brake. 2. Make sure that at complete brake pedal travel, the park detent and pawl are fully engaged.
Workman e2050/e2065 Page 3 – 12 Electrical System (Rev . B) Accelerator Potentiometer Adjustment The accelerator potentiometer is used as one of the in- puts for the vehicle controller and is attached t o the ped- al frame under the dash (Fig.
Rev . A Workman e2050/e2065 Page 3 – 13 Electrical System (Rev . B) Accelerator System Calibration The accelerator system on the Workman e2050 and e2065 includes the accelerator pedal assembly , the ac- celerator potentiometer , the accelerator switch and the controller .
Workman e2050/e2065 Page 3 – 14 Electrical System (Rev . B) Component T esting For accurate resistance and/or continuity checks, elec- trically disconnect the component being tested from the circuit (e.g. disconnect the harness wire connectors from the vehicle on/off switch before doing a continuity check on the on/off switch).
Workman e2050/e2065 Page 3 – 15 Electrical System (Rev . B) Battery Discharge Indicator and Hour Meter Gauge The combination battery discharge indicator and hour meter gauge is located on the dash panel (Fig. 19). Th e battery indicator identifies state of charge of the bat- tery pack.
Workman e2050/e2065 Page 3 – 16 Electrical System (Rev . B) V ehicle Direction (Forward/Reverse) and Headlight Switches The vehicle direction (forward/reverse) switch (Fig. 21) and headlight switch (Fig. 22) are located on the control panel. These two switches have identical logic.
Workman e2050/e2065 Page 3 – 17 Electrical System (Rev . B) V ehicle Status Light The vehicle status light is located on the control panel (Fig. 24). During normal operation, the status light should be continuously illuminated. A vehicle electrical problem will be identified by a flashing status light.
Workman e2050/e2065 Page 3 – 18 Electrical System (Rev . B) Supervisor Speed Limit Switch (Workman e2050) The supervisor speed limit switch is open in Off position (key vertical) and closed in On position (key rotated clockwise).
Workman e2050/e2065 Page 3 – 19 Electrical System (Rev . B) Charger Interlock Switch The charger interlock switch is located behind the char- ger receptacle plate on the front of the seat base (Fig.
Workman e2050/e2065 Page 3 – 20 Electrical System (Rev . B) Main and Accessories Contactors T wo contactors (solenoids) are used on the Workman e2050 and e2065 for circuit control. The main contactor provides current to the vehicle con- troller and is energized when the on/off switch is ON.
Workman e2050/e2065 Page 3 – 21 Electrical System (Rev . B) 6. Replace contactor if necessary . 7. Reconnect electrical connections to contactor . If main contactor connections were removed, use Figure 34 as a guide for reattaching cable and wire harness connections.
Workman e2050/e2065 Page 3 – 22 Electrical System (Rev . B) Fuses There are three (3) fuses in the W orkman electrical sys- tem. T wo (2) of the fuses are located beneath the steering column (Fig. 35). These fuses supply power to the fol- lowing: Th e upper 10 ampere fuse (F2) supplies power to the on/off switch and switched circuits.
Workman e2050/e2065 Page 3 – 23 Electrical System (Rev . B) Fusible Links The wiring harness for the Workman includes three (3) fusible links for circuit protection (Fig. 37). T wo fusible links attach to the same main contactor post as the main fuse.
Workman e2050/e2065 Page 3 – 24 Electrical System (Rev . B) Accelerator Switch The accelerator switch is a four terminal, two circuit switch that is located on the control pedal frame (Fig. 38). The W orkman e2050 and e2065 use only one of the switch circuits (terminals 3 and 4).
Workman e2050/e2065 Page 3 – 25 Electrical System (Rev . B) Accelerator Potentiometer The accelerator potentiometer is attached to the pedal frame under the dash (Fig. 40). This potentiometer is used as one of the inputs for the vehicle controller to command vehicle speed.
Workman e2050/e2065 Page 3 – 26 Electrical System (Rev . B) Controller Th e W orkman controller is secured to the rear frame un- der the controller cover beneath the bed (Fig.
Workman e2050/e2065 Page 3 – 27 Electrical System (Rev . B) 1 Flash System inoperable. T urn on/off switch OFF , wait several seconds and turn on/off switch ON. If controller does not reset correctly , controller replacement may be necessary . 2 Flashes The accelerator pedal was depressed when on/off switch was turned ON.
Rev . D Workman e2050/e2065 Page 3 - - 28 Electrical System (Rev . B) Service and Repairs Battery Service 1. Battery (8 used) 2. Battery rod (2 used) 3. Negative cable to vehicle 4. Lock washer (2 used per battery) 5. Hex nut (2 used per battery) 6. Cable terminal boot 7.
Workman e2050/e2065 Page 3 – 29 Electrical System (Rev . B) Removal (Fig. 43) W ARNING POTENTIAL HAZARD: The battery terminals, metal tools and metal ve- hicle parts could short together . WHA T CAN HAPPEN: Sparks can cause the battery gasses to explode.
Workman e2050/e2065 Page 3 – 30 Electrical System (Rev . B) Charging When the vehicle is not in use, it is recommended to keep the batteries charged by connecting the battery charger that is included with the vehicle. The Workman e2050/e2065 charger is designed to automatically charge the batteries fully without overcharging.
Workman e2050/e2065 Page 3 – 31 Electrical System (Rev . B) T esting When testing batteries in the Workman e2050 and e2065, it i s important to test all batteries. Proper perfor- mance of the vehicle depends on all batteries being in good condition.
Workman e2050/e2065 Page 3 – 32 Electrical System (Rev . B) Battery Storage If the vehicle will be stored for any period of time, check battery electrolyte level, adjust level if needed and then connect battery charger to vehicle.
Workman e2050/e2065 Page 3 – 33 Electrical System (Rev . B) T raction Motor Brushes The traction motor in the Workman e2050/e2065 uses eight (8) brushes. T raction motor brushes should be in- spected every 500 hours of operation or annually . Inspection 1.
Workman e2050/e2065 Page 3 – 34 Electrical System (Rev . B) T raction Motor 1. Socket head screw (6 used) 2. Flat washer (6 used) 3. Flange nut 4. Support bracket 5. Carriage screw 6. T ransaxle mount plate 7. Rubber damper 8. T raction motor 9. Fan 10.
Workman e2050/e2065 Page 3 – 35 Electrical System (Rev . B) 4. Disconnect wires from traction motor (Fig. 52): A. While retaining lower nut, remove upper nut and wire connector from motor terminals A1, A2, F1 and F2. B. Unplug motor temperature sensor from vehicle wire harness.
Workman e2050/e2065 Page 3 – 36 Electrical System (Rev . B) 3. Apply antiseize lubricant or axle grease to the splines of the transaxle and motor shafts. Apply grease to lip of seal in transaxle bore. CAUTION T o prevent motor damage and personal injury , make sure that traction motor is well sup- ported as it is installed.
Workman e2050/e2065 Page 3 – 37 Electrical System (Rev . B) This page is intentionally blank. Electrical System.
Workman e2050/e2065 Page 3 – 38 Electrical System (Rev . B) T raction Motor Service 1. Frame and field assembly 2. Armature 3. Brush lead (2 used) 4. Cap screw (2 used per brush lead) 5. Cap screw (4 used) 6. Cap screw (8 used) 7. Brush (8 used) 8. High temperature sensor 9.
Workman e2050/e2065 Page 3 – 39 Electrical System (Rev . B) Brush Service 1. Check the brush springs for correct alignment on the back of the brush. A brush spring that does not apply equal pressure on the center of the brush will cause the brush to wear unevenly .
Workman e2050/e2065 Page 3 – 40 Electrical System (Rev . B) Commutator Service 1. Chuck armature on the commutator end–bearing journal and support the drive end of armature using the ”live” center of the shaft. With the armature supported on both ends, measure the commutator runout and the bar to bar differences with a dial gauge.
Workman e2050/e2065 Page 3 – 41 Electrical System (Rev . B) Assembly (Fig. 57) NOTE: After the motor has been disassembled, it is recommended that a new commutator end head bear- ing be installed because removed bearing may have been damaged during disassembly .
Workman e2050/e2065 Page 3 – 42 Electrical System (Rev . B) Battery Charger 1. Upper case 2. T ransformer 3. Lower case 4. SCR assembly 5. Control board 6.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 1 Chapter 4 T ransaxle and Brakes T able of Contents SPECIFICA TIONS 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . TROUBLESHOOTING 4 . . . . . . . . . . . . . . . . . . . . . .
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 2 This page is intentionally blank..
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 3 Specifications Item Description T ransaxle T ransaxle Fluid Capacity 2 quarts (1.9 liters) T ransaxle Fluid 10W–30 Motor Oil T ransax.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 4 T roubleshooting Brakes Problem Possible Cause Brake pedal goes to the floor . Brakes are incorrectly adjusted (Workman e2050). Brake cable is loose or broken (Workman e2050). Rear brake shoes are excessively worn.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 5 Brakes (continued) Problem Possible Cause Brakes drag. Parking brake is applied. Brakes are incorrectly adjusted (Workman e2050). Rear shoe–to–shoe spring(s) is (are) weak or broken.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 6 Adjustments Adjust Brakes (Workman e2050) Th e recommended brake pedal travel is from 1” to 1 1/2” (25.4 to 38.1 mm) with a 75 to 100 pound (34 to 45.4 kg) input force to the brake pedal.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 7 This page is intentionally blank. T ransaxle and Brakes.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 8 Service and Repairs Rear Wheels and Brakes Figure 3 1. Lug nut (5 used per wheel) 2. Wheel assembly 3. Brake drum 4. Axle shaft 5. Wheel stud (5 used per wheel) 6. Flange head screw (4 used per brake) 7.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 9 Installation (Fig. 3) IMPORT ANT : On W orkman e2050 vehicles, the brake actuator levers must be positioned below the trans- axle mount. On Workman e2065 vehicles, the levers should be positioned above the transaxle mount.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 1 0 (Rev. C) Brake Service (Workman e2050) Figure 5 1. Backing plate 2. Hold down pin 3. Bottom shoe–to–shoe spring 4. T op shoe–to–shoe spring 5. Auto adjust spring 6. Shoe cup (spring loaded) 7.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 1 1 (Rev. C) Disassembly (Fig. 5) 1. Remove auto adjust spring and shoe–to–shoe springs from brake shoes. 2. Remove hold down pins and shoe cups securing the brake shoes to the backing plate.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 12 Rear Brake Service (Workman e2065) 1. Brake backing plate 2. W asher head screw 3. Brake shoe 4. Lower spring 5. Wheel cylinder 6. Parking brake lever (LH shown) 7. Belleville washer 8.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 13 Inspection (Fig. 6) 1. Inspect brake drums. IMPORT ANT : Brake drum machining is not recom- mended. Replace brake drums as a set to maintain equal braking forces. A. Clean drums with denatured alcohol.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 14 Hydraulic Brake System (Workman e2065) 1. Brake caliper (LH) 2. Brake caliper (RH) 3. Brake rotor (2 used) 4. Front brake tube 5. Front brake hose 6. Carriage screw 7. Rear brake tube 8.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 15 Bleed Brake System (Workman e2065) 1. Connect a suitable transparent hose to bleeder valve on a wheel cylinder or caliper . Submerge other end of hose in a glass container partially filled with clean brake fluid.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 16 Front Brake Calipers (Workman e2065) 1. LH brake caliper 2. RH brake caliper 3. Lock washer (2 per caliper used) 4. Cap screw (2 per caliper used) 5. Wheel hub assembly 6. Brake rotor 7.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 17 Removal (Fig. 8) 1. Park machine on a level surface, stop engine, set parking brake and remove key from the ignition switch. W ARNING Before jacking up the machine, review and follow Jacking Instructions in Chapter 1 – Safety .
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 18 Brake Master Cylinder (Workman e2065) 1. Master cylinder 2. Cap screw 3. Brake pedal 4. Clevis pin 5. Cotter pin 6. Flange head nut 7. Pedal frame Figure 10 7 3 5 6 2 1 4 FRONT RIGHT Removal (Fig.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 19 Brake Master Cylinder Service (Workman e2065) Disassembly (Fig. 1 1) 1. Remove reservoir and flange seal. Push in on the push rod so the stop pin can be removed. 2. Disconnect lower end of the dust cover from the housing.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 20 Parking Brake (Workman e2065) 1. Parking brake cover 2. Operator seat 3. Seat base 4. Cable equalizer bracket 5. Parking brake lever 6. Curved washer 7. Lock nut 8. Flat washer 9. Flange head screw (4 used) 10.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 21 Disassembly (Fig. 12) 1. Park machine on a level surface, stop engine and re- move key from the ignition switch. Chock wheels to pre- vent the machine from moving. 2. Disconnect both brake cables from rear of machine: A.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 22 T ransaxle 1. Socket head screw (6 used) 2. Flange nut 3. Carriage screw (5 used) 4. Support bracket 5. T ransaxle mount plate 6. Rubber damper 7. T raction motor 8. Fan 9. Roll pin (2 used) 10.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 23 Removal (Fig. 13) 1. Park vehicle on a level surface, turn on/of f switch OFF , set parking brake and remove key from switch. 2. Remove cargo bed from vehicle (see Cargo Bed Re - moval in Service and Repairs section of Chapter 5 – Chassis).
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 24 Installation (Fig. 13) 1. If removed, install traction motor to transaxle (see T raction Motor Installation in Service and Repairs sec- tion of Chapter 3 – Electrical System). 2. Position transaxle and motor assembly to the rear frame.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 25 This page is intentionally blank. T ransaxle and Brakes.
Workman e2050/e2065 T ransaxle and Brakes (Rev . B) Page 4 – 26 T ransaxle Service 1. Oil seal 2. Wheel stud (5 used per side) 3. Axle shaft 4. Ball bearing 5. Input shaft 6. Ball bearing 7. O–ring 8. Retaining ring 9. Endcap plug 10. Ball bearing 1 1.
Workman e2050/e2065 Page 5 – 1 Chassis (Rev . B) Chapter 5 Chassis T able of Contents SPECIFICA TIONS 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . TROUBLESHOOTING 3 . . . . . . . . . . . . . . . . . . . . . . . . . Suspension and Steering 3 .
Workman e2050/e2065 Page 5 – 2 Chassis (Rev . B) Specifications Item Description Front tire (22 x 9.5 – 10, 4 ply) pressure 8 to 22 PSI (0.55 to 1.
Workman e2050/e2065 Page 5 – 3 Chassis (Rev . B) T roubleshooting Suspension and Steering Problem Possible Cause Front end is noisy . Front wheel lug nuts are loose. Front wheel bearings are loose or worn. Front end components are loose or worn. Steering gear is loose.
Workman e2050/e2065 Page 5 – 4 Chassis (Rev . B) Suspension and Steering (continued) Problem Possible Cause Steering is hard. T ire pressure is low or uneven between tires. Front wheel alignment (toe–in) is incorrect. Steering linkage is binding or damaged.
Workman e2050/e2065 Page 5 – 5 Chassis (Rev . B) Service and Repairs Check Tire Pressure The tire pressure range for front and rear tires is 8 to 22 PS I (0.55 to 1.52 bar). The tire pressure needed is deter- mined by the payload carried. The lower the air pressure, the less the compaction and tire marks are minimized.
Workman e2050/e2065 Page 5 – 6 Chassis (Rev . B) Upper Steering 1. Nut 2. Lock washer 3. Steering wheel 4. Flange lock nut 5. Steering gearbox 6. Cap screw 7. Lock washer 8. Steering shaft 9. Cap screw (3 used) 10. Upper steering bushing 1 1. Carriage bolt (4 used) 12.
Workman e2050/e2065 Page 5 – 7 Chassis (Rev . B) Removal (Fig. 1) 1. Park vehicle on a level surface, turn on/of f switch OF F , set parking brake and remove key from the switch.
Workman e2050/e2065 Page 5 – 8 Chassis (Rev . B) Steering Gearbox 1. Gasket 2. Hex washer head screw (4 used) 3. Seal 4. Sector gear 5. Flat washer 6. Ball bearing 7. Output shaft spacer 8. Stepped washer 9. Flange head screw with patch lock 10. Ball bearing 1 1.
Workman e2050/e2065 Page 5 – 9 Chassis (Rev . B) Disassembly (Fig. 2) IMPORT ANT : Do not reuse flange head screw with patch lock (item 9) after it has been removed. 1. Remove flange head screw with patch lock (item 9) and stepped washer (item 8) from Pitman arm.
Workman e2050/e2065 Page 5 – 10 Chassis (Rev . B) Front Wheels (Workman e2050) 1. Spindle (LH shown) 2. Bearing (with retaining ring) 3. Wheel stud (5 per wheel) 4. Wheel hub 5. Spacer 6. Tire/wheel assembly 7. Lug nut (5 per wheel) 8. Flat washer 9.
Workman e2050/e2065 Page 5 – 1 1 Chassis (Rev . B) Removal (Fig. 3) 1. Park vehicle on a level surface, turn on/of f switch OFF , set parking brake and remove key from the on/off switch. W ARNING Before jacking up the machine, review and follow Jacking Instructions in Operator ’ s Manual and Chapter 1 – Safety .
Workman e2050/e2065 Page 5 – 12 Chassis (Rev . B) Lower Steering (Workman e2050) 1. Pitman arm 2. Grease fitting 3. Cap screw (king pin) 4. Spindle (LH) 5. Front wheel assembly 6. Flat washer 7. Large flat washer 8. Cap screw 9. Dust cap 10. Lock nut 1 1.
Workman e2050/e2065 Page 5 – 13 Chassis (Rev . B) Removal (Fig. 5) 1. Park vehicle on a level surface, turn on/of f switch OFF , set parking brake and remove key from the on/off switch. W ARNING Before jacking up the machine, review and follow Jacking Instructions in Operator ’ s Manual and Chapter 1 – Safety .
Workman e2050/e2065 Page 5 – 14 Chassis (Rev . B) Front Wheels and Lower Steering (Workman e2065) 1. Wheel assembly 2. Lug nut (5 used per wheel) 3. Dust cap 4. Cotter pin 5. Nut retainer 6. Jam nut 7. T ab washer 8. Bearing cone 9. Bearing cup 10. Wheel hub 1 1.
Workman e2050/e2065 Page 5 – 15 Chassis (Rev . B) 3. Remove lug nuts and pull wheel assembly from ma- chine. 4. Remove brake caliper from spindle (see Front Brake Calipers in the Service and Repairs section of Chapter 4 – T ransaxle and Brakes). Position caliper away from wheel hub and spindle.
Workman e2050/e2065 Page 5 – 16 Chassis (Rev . B) A–arm and Frame Pivot Y oke 1. Ride height adjustment bolt 2. Bushing 3. Grease fitting 4. A–arm (LH) 5. Flange nut 6. Lock nut 7. Lock washer 8. Centering bolt (2 used per A–arm) 9. T ravel limiting bolt 10.
Workman e2050/e2065 Page 5 – 17 Chassis (Rev . B) A–arm Removal (Fig. 7) 1. Park vehicle on a level surface, turn on/of f switch OFF , set parking brake and remove key from the on/off switch. W ARNING Before jacking up the machine, review and follow Jacking Instructions in Operator ’ s Manual and Chapter 1 – Safety .
Workman e2050/e2065 Page 5 – 18 Chassis (Rev . B) Pivot Y oke Removal (Fig. 7) 1. Park vehicle on a level surface, turn on/of f switch OFF , set parking brake and remove key from the on/off switch.
Workman e2050/e2065 Page 5 – 19 Chassis (Rev . B) This page is intentionally blank. Chassis.
Workman e2050/e2065 Page 5 – 20 Chassis (Rev . B) Seat Base 1. Seat 2. Seat bracket 3. Rubber receptacle 4. Rivet 5. Cap screw (4 used per seat) 6. Screw 7. Holding post 8. Seat base 9. Seat base tray 10. Flange head screw (8 used) 1 1. Flat washer (4 used) 12.
Workman e2050/e2065 Page 5 – 21 Chassis (Rev . B) Removal (Fig. 1 1) 1. Park vehicle on a level surface, turn on/of f switch OFF , set parking brake and remove key from the on/off switch.
Workman e2050/e2065 Page 5 – 22 Chassis (Rev . B) Front Hood 1. Hood 2. Flange head screw (6 used) 3. Dash 4. Flange nut (6 used) 5. Fender (LH shown) 6. Bumper 7. Flat washer (2 used) 8. Cap screw (2 used) 9. Flat washer (4 used) 10. Flange head screw (2 used) 1 1.
Workman e2050/e2065 Page 5 – 23 Chassis (Rev . B) Removal (Fig. 14) 1. Park vehicle on a level surface, turn on/of f switch OFF , set parking brake and remove key from the on/off switch.
Workman e2050/e2065 Page 5 – 24 Chassis (Rev . B) Cargo Bed 1. Cargo bed 2. Striker plate (2 used) 3. Screw (3 per striker plate) 4. T ailgate channel 5. RH latch rod 6. RH latch bracket 7. Grip knob 8. T ailgate 9. LH latch rod 10. Screw (2 per bracket) 1 1.
Rev . B Workman e2050 Electrical Diagrams Page 6 – 1 Chapter 6 Electrical Diagrams T able of Contents ELECTRICAL SCHEMA TIC Electrical Schematic 3 . . . . . . . . . . . . . . . . . . . . . . . . . ELECTRICAL CIRCUIT DRA WINGS On/Off Switch T urned On 4 .
Workman e2050 Electrical Diagrams Page 6 – 2 This page is intentionally blank..
Rev . B Page 6 – 3 Electrical Schematic W orkman e2050/e2065 Contactors shown de–energized RUN 15 14 M1 M2 FL3 BU B BK BK BK 4 Y W 16 13 12 45 F2 F1 FL1 FL2 F1 FRONT HORN SWITCH W HORN SWITCH HOOK.
Rev . B Page 6 – 4 RUN 15 14 M1 M2 FL3 BU B BK BK BK 4 Y W 16 13 12 45 F2 F1 FL1 FL2 F1 FRONT HORN SWITCH W HORN SWITCH HOOK UP R (PEDAL NOT PUSHED IN) CW T VIO/BK Y PK OR NC NC NC OR R/W OFF 1 1 PR.
Rev . B Page 6 – 5 RUN 15 14 M1 M2 FL3 BU B BK BK BK 4 Y W 16 13 12 45 F2 F1 FL1 FL2 F1 FRONT HORN SWITCH W HORN SWITCH HOOK UP R (PEDAL PUSHED IN) CW T VIO/BK Y PK OR NC NC NC OR R/W OFF 1 1 PROGRA.
Rev . B Page 6 – 6 RUN 15 14 M1 M2 FL3 BU B BK BK BK 4 Y W 16 13 12 45 F2 F1 FL1 FL2 F1 FRONT HORN SWITCH W HORN SWITCH HOOK UP R (PEDAL NOT PUSHED IN) CW T VIO/BK Y PK OR NC NC NC OR R/W OFF 1 1 PR.
Page 6 – 7 Electrical Harness Drawing W orkman e2050.
Page 6 – 8 Electrical Harness W orkman e2050 Wiring Diagram ORANGE RED/WHITE WHITE PINK RED BLACK ORANGE BLUE ORANGE ORANGE BROWN BLACK BLACK BLACK BLACK BLACK GREEN BLACK TA N TA N BLACK BLUE BLUE .
Rev . B Page 6 – 9 Electrical Harness Drawing W orkman e2065.
Rev . B Page 6 – 10 Electrical Harness W orkman e2065 Wiring Diagram ORANGE RED/WHITE PINK ORANGE BLUE ORANGE ORANGE BLACK BLACK BLACK BROWN BLACK BLUE RED/WHITE PINK BLUE/WHITE YELLOW BLUE YELLOW R.
Ein wichtiger Punkt beim Kauf des Geräts Toro e2050 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Toro e2050 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Toro e2050 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Toro e2050 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Toro e2050 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Toro e2050 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Toro e2050 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Toro e2050. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Toro e2050 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
