Benutzeranleitung / Produktwartung CST-38 des Produzenten TOA Electronics
Zur Seite of 24
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 1 36" Wood Burning Fireplaces P/N 700,023M REV. C 06/2005 CST -38 CPF-38 MODELS CUSTOM SERIES This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 2 IMPORTANT: PLEASE READ AND UNDERSTAND THESE RULES TO FOLLOW FOR SAFETY. 1. Before starting your fireplace installation, read these installation instructions carefully to be sure you understand them completely and in entirety.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 3 Figure 1 TYPICAL INSTALLATION *Construction Materials: • framing materials • paneling • particle board • flooring • millboard • dry wall • plywood • etc. PRECAUTIONS Note: These fireplace systems are not difficult to install.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 4 For questions, please call your distributor or the manufacturer. Special restrictions apply to the front and facing of the fireplace and nearby walls (See pages 18, 19 and 20 ). CHIMNEY SYSTEM These fireplaces are designed and code listed for use with Security Chimneys FTF8 chimney System only.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 5 Figure 7 Figure 6 Carefully consider the position of the fireplace opening with respect to the location of adja- cent or nearby stairwells, bath or k.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 6 The safety strips should extend in front and sides of the fireplace opening 2" (51 mm) . In the event a wooden support is used to elevate the fi.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 7 FIREPLACE SPECIFICATIONS Figure 15 39 ¹⁄₄ " (997 mm) 23 ¹⁵⁄₁₆ " (608 mm) 25 ³⁄₁₆ " (640 mm) 8" (203 mm) Left.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 8 Figure 16 Figure 19 CPF CST Figure 17 Figure 18 Figure 21 CST - Front View CST - End View CPF - Right Front View CPF - End View FRAMING SPECIFICATIONS Figure 20 7" Min.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 9 Figure 22 FRAMING WALL VARIATIONS As many as six (6) different framed wall con- figurations can be constructed to enclose the CST and CPF fireplaces. The following illustra- tions depict these variations of wall enclosures.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 10 A minimum 2" (51 mm) air space must be reserved for all combustible materials extend- ing for any continuous length surrounding the chimney. Reference Figures 24 and 25 and charts “Fram- ing Dimensions for Ceiling and Roof” on page 8, which specify minimum ceiling and roof dimensions.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 11 Check vertical alignment of chimney pipe so that it projects from the roof in a true vertical position. Security's chimney sections do not need to be screwed together. Additional rein- forcement is not necessary, except in certain offset conditions (see to page 16, Figure 47 ).
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 12 Figure 40 Step 10. Using an FTF8-CTD Round Termi- nation: 1. Hold FTF8-CTD over top of last chimney section ( Figure 40 ). 2. Center inner slip section in inner flue pipe- slip down. 3. Center outer locking section over outer flue pipe.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13 Figure 41 TEN FOOT RULE SUMMARY The minimum chimney height above the roof and/or to adjacent walls and buildings is speci- fied by all major building codes.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 14 11 0 11 1 0 0 0 279 0.28 17 1 5 0 1 0 0 432 0.43 21 ¹⁄₄ 19 ¹⁄₄ 2 0 0 0 540 0.54 27 ¹⁄₄ 23 ¹⁄₄ 1 1 0 0 692 0.69 35 2 11 0 0 1 0 889 0.89 47 3 11 0 0 0 1 1194 1.19 51 ¹⁄₄ 43 ¹⁄₄ 0 1 1 0 1302 1.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 15 A B FTF8-ES30 Number of FTF8 A B Offset Height Offset/Return FTF8-S4 Chimney Sections Offset Height (Inches) (Inches) Elbow Set Stabilizer 12" .
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 16 OFFSET ELBOW ASSEMBLY Offset elbows install the same as chimney sections. First, snap the inner section INTO the preceding inner section of flue. Check connec- tion by pulling up slightly to ensure a tight fit.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 17 There is a one-hand operated shut-off valve located in the enclosed corner of the fireplace opening behind the screen.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 18 GAS LINE INSTALLATION The CST and CPF fireplaces have been ap- proved to accept a ¹⁄₂ " (13 mm) gas line for an approved gas appliance. Always have the appli- ance installed by a qualified, licensed plumber in accordance with all local building codes.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 19 If there is a continuous perpendicular side wall closer than 18" (mm) from the CST-38 fireplace opening, it must be protected with a 40 x 40&qu.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 20 Example: Given that the required “R value” for a suitable hearth extension used must be equal to or greater than: “R” = r x T L = 1.19 x 1 " = 1.19. If it is desired to elevate a marble hearth exten- sion to a level of 5" or more above the floor surface.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 21 ACCESSORIES AND COMPONENTS 63L10 FTF8-12 63L13 FTF8-18 63L14 FTF8-36 Chimney Section 63L15 FTF8-48 Canadian (Outside) 62L92 FTF8-18C Chimney Section.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 22 Combustion Air Kit 011761 AK-4 (Less Duct) 011763 AK-4LD “All-Glass TM ” 38AEP Aluminum End Panel 38AEP-BB “All-Glass TM ” Cabinet Doors 38T.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 23.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 24 Printed in U.S.A. © 2001 by LENNOX HEARTH PRODUCTS P/N 700,023M REV. C 06/2005 The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
Ein wichtiger Punkt beim Kauf des Geräts TOA Electronics CST-38 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie TOA Electronics CST-38 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für TOA Electronics CST-38 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von TOA Electronics CST-38 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über TOA Electronics CST-38 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon TOA Electronics CST-38 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von TOA Electronics CST-38 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit TOA Electronics CST-38. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei TOA Electronics CST-38 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
