Benutzeranleitung / Produktwartung JD 62-6430 des Produzenten Tiger
Zur Seite of 58
P AR TS LISTING WITH MOUNTING AND OPERA TING INSTRUCTIONS SNOW PLOW ASSEMBLIES JD 62-6430 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www .
T O THE OWNER / OPERA T OR / DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices.
FOR W ARD This manual contains information about many features of the T iger mowing and roadside maintenance equipment. Some of these include: Safety precautions, Assembly instructions, Operations, Maintenance and Parts. This manual will also assist you in the proper break-in, daily care, and troubleshooting of your new mower .
.
T ABLE OF CONTENTS SAFETY SECTION _____________________________________ 1 ASSEMBL Y / MOUNTING SECTION ______________________ 2 OPERA TION SECTION _________________________________ 3 MAINTENANCE SECTI.
.
Safety Section 1-1 © 2009 Alamo Grou p Inc. SAFETY SECTION.
SAFETY Front & Mid Plow Wing s Safety Section 1-2 © 2009 Alamo Grou p Inc. SAFETY GENERAL SAFETY INSTRU CTIONS AND PRACTICES A careful operator is the best opera tor . Safety is of primary import ance to the manu facturer and should be to the owner/operator .
SAFETY Front & Mid Plow Wings Safety Section 1-3 © 2009 Alamo Grou p Inc. SAFETY Repeated or subst antial breathing of hazardou s dusts, including crystalline silica, could ca use fatal or serious respiratory disease including silicosis. Concrete, maso nry , many types of rock, and various other materials contain silica sand.
SAFETY Front & Mid Plow Wing s Safety Section 1-4 © 2009 Alamo Grou p Inc. SAFETY OPERA TOR SAFETY INST RUCTIONS AND PRACTICES All Safety Shields, Guards and other Pr otective Safety devices sh ould be used and maintaine d in good working condition.
SAFETY Front & Mid Plow Wings Safety Section 1-5 © 2009 Alamo Grou p Inc. SAFETY Prolonged operation o f the Snow Plow ma y cause operato r boredom and/or fatigue affecting the safe operation of the Sn ow Plow and T ruck or Power unit.
SAFETY Front & Mid Plow Wing s Safety Section 1-6 © 2009 Alamo Grou p Inc. SAFETY Always wear a seat belt while driving the equipment dur ing operation and transpor t. Serious injury or even death could result fr om falling from the operator ’s station or from being involved in a collision.
SAFETY Front & Mid Plow Wings Safety Section 1-7 © 2009 Alamo Grou p Inc. SAFETY Unplowed snow , piled ice and debris, and snow dr if ts lef t behind the equipmen t mi gh t pose a driving hazard to vehicle traffic colliding with the debris or lo sing traction on the material.
SAFETY Front & Mid Plow Wing s Safety Section 1-8 © 2009 Alamo Grou p Inc. SAFETY Allow passengers only in si tuations wh ere their presence is involved in the opera tion (operator training , supervision, maintenance inspection). Ne ver carry passen gers whose presence distract s from the safe operation or transport of th e equipment.
SAFETY Front & Mid Plow Wings Safety Section 1-9 © 2009 Alamo Grou p Inc. SAFETY CONNECTING OR DISCONNECTING IMPLEMENT SAFETY INSTRUCTIONS AND PRACTICES Always turn on all safety lights and flashers wh en you operate the Snow Plow . (SNPS-5) Be particu larly careful in transport.
SAFETY Front & Mid Plow Wings Safety Section 1-10 © 2009 Alamo Grou p Inc. SAFETY MAINTENANCE AND SER VICE SA FETY INSTRUCTIONS AND PRACTICES Perform service, rep airs and lubrication acco rd ing to the maintenance section.
SAFETY Front & Mid Plow Wings Safety Section 1-11 © 2009 Alamo Grou p Inc. SAFETY Never leave the Snow Plow unattended while the plow is in the raised position. Accident al operation of the lifting lever or a hydraulic failure may cause a sudden drop of the un it which could result in injury or d eath by crushing.
SAFETY Front & Mid Plow Wings Safety Section 1-12 © 2009 Alamo Grou p Inc. SAFETY Do not operate this equipment with hydraulic oil or fuel leaking.
SAFETY Front & Mid Plow Wings Safety Section 1-13 © 2009 Alamo Grou p Inc. SAFETY TRANSPORTING SAFETY INSTRUCTIONS AND PRACTICES Secure the wing for transport when not plowing. Secure wing in transport position using wing transport safety c hain.
SAFETY Front & Mid Plow Wings Safety Section 1-14 © 2009 Alamo Grou p Inc. SAFETY Federal Laws and Re gulations This section is intended to explain in broad terms the conc ept and effect of federal laws and regulations concerning employer and employee eq uipment operators.
ASSEMBL Y SECTION Assembly Section 2-1.
Assembly Section 2-2 ASSEMBL Y Before attempting to mount or service your Tiger equipment, it is import ant to read and underst and all of the information in the Safety section of this manual. Check complete shipment list against the packing list to make sure there are no shortages.
Assembly Section 2-3 ASSEMBL Y MUL TIPLIER V AL VE CONTROLLER MOUNTING The Multiplier V alve Controller comes with two worm-screw ties that are used to attach the Controller to the Tractor Joystick as shown below .
Assembly Section 2-4 ASSEMBL Y HYDRAULIC MUL TIPLIER V AL VE MOUNTING Align the mounting bracket to the existing holes on rear of the tractor by the PTO. Secure the bracket to the tractor with the existing hardware. Then align the holes and secure the valve to the mounting bracket as shown in the parts section.
Assembly Section 2-5 ASSEMBL Y HYDRAULIC SYSTEM DIAGRAM.
Assembly Section 2-6 ASSEMBL Y ADJUSTING REAR WHEELS Follow the instructions in the tractor owners manual for adjusting tires and rims. The rear wheels MUST be adjusted to the widest setting. NOTE: This may require switching the wheels to opposite sides of the tractor .
Assembly Section 2-7 ASSEMBL Y WELDING MAIN FRAME Make sure you use the appropriate safety equipment. Weld the T angs onto your existing Main Frame as shown below . Next, weld on the Boss’ making sure the orientation of the cross holes for the bolts are correct.
Assembly Section 2-8 ASSEMBL Y FINAL PREP ARA TION FOR OPERA TION Place operators safety and operation decals on the steering column and side counsel where they are clearly visible to the operator . These decals should be understood by each operator of the machine in conjunction with the safety and operation section of this book.
Snow Plow Operation Section 3-1 OPERA TION OPERA TION SECTION.
Snow Plow Operation Section 3-2 OPERA TION Safety is of primary importance to the owner / operator and to the manufacturer . The first section of this manual includes a list of Safety Messages, that, if followed, will help protect the operator and bystanders from injury or death.
Snow Plow Operation Section 3-3 OPERA TION The Push Arm S top height is controlled with the 3-point hitch control lever . Follow the instructions for this control is the tractor operators manual.
Snow Plow Operation Section 3-4 OPERA TION TRANSPORTING MOWER ON A TRAILER T ransporting unit by flatbed trailer: Most tractors with a side mounted plow attached will be over legal transporting width (102” wide). For this reason, one of the following procedures must be followed.
Snow Plow Operation Section 3-5 OPERA TION TRACT OR PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is of f, all rotation has stop and the tractor is in the Park with the parking brake engaged.
Snow Plow Operation Section 3-6 OPERA TION.
Maintenance Section 4 -1 MAINTENANCE SECTION.
Page 2 of 3 IN SEASON MAINTENANCE Snow removal equip ment must be cared for and maintai ned reg ular ly . Daily or pre-r oute inspec tion an d mainte nance ar e nece ssary. Fail ure to do s o may affect effi ciency and safety . A vi sual inspectio n must be c arri ed out a fter ev ery 8 hours o f opera tion.
Page 3 of 3 END OF SEASON MAINTENANCE GROUND ENGAGING COMPONENTS CUTTING EDGES & GUARDS Repl ace any broken cutti ng edg es, unevenl y or ex cessiv ely wor n cutting edg es, and broke n or wor n wear guards. RUNNING GEAR Repl ace broken, w orn, or missi ng run ning g ear shoes, a nd any da mag ed adjuster leg compon ents.
NOTES.
P ARTS SECTION JD62-6430 SNOW PLOW Parts Section 5-1.
JD6030 SNOW PLOW Parts Section 5-2 The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual.
JD6030 SNOW PLOW Parts Section 5-3 P ARTS SECTION T ABLE OF CONTENTS SECTION P A G E TRACTOR SPECIFIC P ARTS: TRACTOR MOUNT KIT - MAIN FRAME 5-4 TRACTOR MOUNT KIT - FRONT HYDRAULICS 5-5 TRACTOR MOUNT .
JD6030 SNOW PLOW Parts Section 5-4 TRACTOR MOUNT KIT - MAIN FRAME 12-07-06 ITEM P ART NO. Q T Y DESCRIPTION 1 R EF * MAIN FRAME 2 063001 18 1 SIDE PLOW WELDMENT 3 21688 3 CAPSCREW ,7/16 x 3-1/4,NC 4 06420125 2 PIN,1.
JD6030 SNOW PLOW Parts Section 5-5 TRACTOR MOUNT KIT - FRONT HYDRAULICS 12-07-06 ITEM P ART NO. Q T Y DESCRIPTION 1 R EF * MAIN FRAME 2 32900 5 QUICK CPLR,MALE,1/2 x 1/2FOR 3 33271 4 ADAPTER,1/2MOR x .
JD6030 SNOW PLOW Parts Section 5-6 TRACTOR MOUNT KIT - PUMP HOSES ITEM P ART NO. Q T Y DESCRIPTION 1 06500258 1 HOSE,1-1/4 x 70 (FROM T ANK T O PUMP) 2 TF4852 2 FLANGE KIT ,#20 3 06500512 1 HOSE,1 x 7.
JD6030 SNOW PLOW Parts Section 5-7 NOTES P AGE INTENSIONALL Y LEFT BLANK.
JD6030 SNOW PLOW Parts Section 5-8 12-04-06 TRACTOR MOUNT KIT - SIDE HYDRAULICS.
JD6030 SNOW PLOW Parts Section 5-9 TRACTOR MOUNT KIT - SIDE HYDRAULICS ITEM PART NO. QTY. DESCRIPTION 1 R EF * MAIN FRAME 2 32900 4 QUICK CPLR,MALE,1/2 x 1/2MOR 3 33271 6 ADAPTER,1/2MOR x 3/8MJ 4 0650.
JD6030 SNOW PLOW Parts Section 5-10 3-POINT ST OP & PUSH ARM.
JD6030 SNOW PLOW Parts Section 5-11 ITEM PART NO. QTY. DESCRIPTION 1 TB1036 1 PIN,TOP LINK,3-POINT 2 T F 1 1 4 3 3 PIN, L YNCH, 7/16 x 2 3 T F 1 12 0 2 PIN,(CAPPED),1-1/8 x 3-7/8 4 063001 15 1 3PNT ,S.
JD6030 SNOW PLOW Parts Section 5-12 MUL TIPLIER V AL VE MOUNTING ITEM PART NO. QTY. DESCRIPTION 1 32900 2 QUICK CPLR,MALE,1/2 x 1/2FOR 2 33382 2 ELBOW ,1/2MOR x 1/2MJ X 90 3 06500251 1 HOSE,1/2 x 28 4.
JD6030 SNOW PLOW Parts Section 5-13 3 & 4 FUNCTION MUL TIPLIER V AL VE BREAKDOWN ITEM P ART NO. Q T Y DESCRIPTION 1 * R EF SMALL NUT (NOT FOR P ARTS SALE) 2 06505165 REF SOLENOID 12V SP 3 06505164.
JD6030 SNOW PLOW Parts Section 5-14 2 FUNCTION MUL TIPLIER V AL VE BREAKDOWN ITEM P ART NO. Q T Y DESCRIPTION 1 * R EF SMALL NUT (NOT FOR P AR TS SALE) 2 06505165 4 SOLENOID 12V SP 3 06505163 2 N/O CA.
JD6030 SNOW PLOW Parts Section 5-15 1 FUNCTION MUL TIPLIER V AL VE BREAKDOWN ITEM P ART NO. Q T Y DESCRIPTION 1 * RE F T ALL NUT (NOT FOR P AR TS SALE) 2 06505162 2 SOLENOID 12V SS 3 06505161 1 N/O CA.
JD6030 SNOW PLOW Parts Section 5-16 R 03-01 ITEM P/N Q T Y DESCRIPTION * 06200420 A V AIL SAFETY LIGHT KIT (INCLUDES ITEMS 1 THRU 9) 1 34800 1 MOUNT ,JD62-6420,ASAE 279.
W ARRANTY SECTION Warranty Section 6-1.
.
W ARRANTY INFORMA TION T iger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrants to the original Retail Customer , the new T iger equipment is free of defects in material and workmanship.
ONE LAST WORD This manual cannot possibly cover all of the potentially hazardous situations you will encounter . By being familiar with the safety rules, operating and maintenance instructions in this manual you can help prevent accidents. The objective of this manual is to help make you a better operator .
Ein wichtiger Punkt beim Kauf des Geräts Tiger JD 62-6430 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Tiger JD 62-6430 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Tiger JD 62-6430 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Tiger JD 62-6430 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Tiger JD 62-6430 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Tiger JD 62-6430 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Tiger JD 62-6430 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Tiger JD 62-6430. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Tiger JD 62-6430 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
