Benutzeranleitung / Produktwartung SX5P CDMA2000 des Produzenten Telular
Zur Seite of 48
05/19/04 Part Number 56029702 P HONECELL ® SX5P CDMA2000 1X • Fixed W ir eless Phone 800/1900 MH Z CDMA U SER M ANU AL.
QUICK CONNECTION GUIDE Phonecell ® SX5 CDMA i User Manual Fixed Wireless Phone T elular Serial Cable or USB Cable GPS Antenna (USA Models Only).
Phonecell ® SX5 CDMA ii User Manual SX5 MENU STRUCTURE Phonebook View Add Edit Erase Time/Alarm Alarm T ime Format Date Format Phone Settings Banner My Phone Number DTMF Length Key V olume Auto Send Delay Freq.
Before installing your Phonecell ® SX5 , carefully remove the contents from the shipping carton and check for evidence of shipping damage. If damage is found, contact your Authorized T elular Distributor or shipping agent immediately .
T ABLE OF CONTENTS QUICK CONNECTION GUIDE .......................................................................................i SX5 MENU STRUCTURE ..............................................................................................ii LIST OF COMPONENTS .
TIME / ALARM ............................................................................................................15 Alarm........................................................................................................................15 T ime Format .
SX5 SETUP RUIM Card Installation (RUIM Model Only) Consult your service provider to determine if your unit is a RUIM model. If so, your SX5 will only be able to make emergency calls until you install a RUIM card. It will not receive calls or allow non-emergency outgoing calls.
Battery Operation The unit will not automatically switch from AC to battery upon loss of AC power . The AC/Battery switch must be changed manually to the battery position - see Figure 5. Battery power will pro- vide up to 4 hours of talk time and 1 1 hours of standby .
Connect the Handset Before you can use the SX5, you must connect the handset cable. 1. Connect the handset cable to the phone jack - see Figure 8. 2. Connect the handset cable to the handset - see Figure 8. Desk Mounting A wedge is included with the SX5 to be used to position the SX5 for easier viewing of the LCD screen and keypad.
Phonecell ® SX5 CDMA 4 User Manual 2. Snap the wedge tabs on the thick end of the wedge into the top tab slot s - see Figure 10 . NOTE: The wedge will fit snugly , so it may be necessary to press the.
Phonecell ® SX5 CDMA 5 User Manual 3. Snap the wedge tabs on the thick end of the wedge into the top tab slots - see Figure 14 . The wedge will fit snugly , so it may be necessary to press the thick end of the wedge towards the bottom tab slots (if the wedge tabs at the thin end have been inserted) in order to snap it into the top tab slots.
RUIM Usage (RUIM Models Only) Y our service provider may require you to install a RUIM in your SX5 for it to operate normally (see RUIM Card Inst allation (page 1) for details). Without a RUIM, these SX5 models will reject incoming calls and allow only emergency outgoing calls.
GETTING TO KNOW YOUR SX5 Function Keys Operation of the SX5 is accomplished through the function keys on the keypad of the unit - see Figure 18 . Figure 18 – SX5 keypad and function keys. LCD Screen - Displays icons, information, and menu options necessary to operate the SX5.
Phonecell ® SX5 CDMA 8 User Manual LCD Screen Icons Icons displayed on the LCD screen indicate the features in use, the st atus of the phone, signal strength and battery status - see Figure 19 . Service Indication Full Service When powered on, the banner and current date and time will display .
CALL FUNCTIONS Making Calls 1. Pick up the handset or Press the SPEAKERPHONE key . The SX5 is now “off-hook.” 2. Listen for dial tone. 3. Dial the phone number . The dialed number will be displayed. The name will also be displayed if it is stored in the phonebook.
Voicemail Access Contact your service provider regarding the availability of voicemail. 1. Press MSG . 2. Select 1: V oice Mail . 3. T o listen to your voicemail, Select 1: Listen . 4. If you have deleted all your messages and the message indicator does not go away after an hour , Press 2: Clr Msg Ind .
Message Lock Message lock password protects the V oice Mail menu. If the message lock is active and you press the MSG key from the idle screen, the unit will prompt you for a password which is your lock code (default is 0000). 1. Press MSG 2. Select 5: Message Options 3.
PHONE BOOK The SX5 can be programmed to store frequently called numbers via an electronic phone book. The SX5 phone book can hold up to 99 entries. Speed Dial by Location A phone book entry can be speed dialed as follows: For entries 1-9, lift the handset and hold down the location number until it dials.
Edit a Phone Book Entry 1. S tart by pressing MENU 2. Select 1: Phone Book 3. Select 3: Edit There are 3 options for editing an entry: 1. All - displays all entries from location 01 through 99 Use Up and down arrows to select the location and Press STO to select it.
View Outgoing Calls 1. S tart by pressing MENU 2. Select 2: Call Logs 3. Select 2: Outgoing 4. Use the up and down arrows to select the desired call and Press STO to view it. T o dial the selected entry , Press FLASH. Then pick up the handset if desired.
Clear Air Time 1. S tart by pressing MENU 2. Select 2: Call Logs 3. Select 7: Clear Air Time This option will clear the phone's memory of how much airtime has been used. TIME / ALARM The SX5 allows you to set an alarm clock that can be used one time or for every day .
RING / ALERT The SX5 is capable of supporting multiple ring tones and types of alerts. T o adjust these settings, follow these instructions. Ring T ype 1. S tart by pressing MENU 2. Select 4: Ring / Alert 3. Select 1: Ring T ype 4. Select the desired option and Press STO to save.
PHONE SETTINGS Banner The banner is the text on the screen shown when the phone is not in use. This can be used to personalize your phone. 1. S tart by pressing MENU . 2. Select 5: Phone Settings . 3. Select 1: Banner . My Phone # (display only) 1. S tart by pressing MENU .
Change Language Displayed On LCD The SX5 is capable of displaying multiple languages on the LCD screen. 1. S tart by pressing MENU . 2. Select 5: Phone Settings . 3. Select 7: Language . 4. Select the desired setting and Press STO to save. Dial T one T ype 1.
Self T est Cycle The unit will perform a periodic self test to ensure the proper operation of the phone. The default setting is 180 minutes (3 hours). 1. S tart by pressing MENU . 2. Select 6: Data Settings . 3. Select 3: Self T est cycle 4. Select between 0 and 65535 minutes and Press STO to save.
V oice Privacy The cellular CDMA network offers inherent voice privacy . Check with your service provider for the availability of enhanced voice privacy mode. If Enhanced is selected, the phone will request Enhanced V oice Privacy and a "P" will be shown on the display if Enhanced V oice Privacy has been granted by the network.
WINDOWS XP/WINDOWS 2000 SETUP T o configure a Windows XP/Windows 2000 computer and SX5 to work together , follow these steps. 1. Connect your computer and the SX5 with a T elular USB cable (part #1L01A043 or 81025901) or serial cable (part #1L01A042 or 81025801).
6. Click on "Don't detect my modem, I will select it from a list". 7. Select "S tandard 19200 bps Modem". Phonecell ® SX5 CDMA 22 User Manual.
8. Select the COM port to use (if a COM port does not display , all COM ports are currently allocated). 9. Click Finish. Phonecell ® SX5 CDMA 23 User Manual.
10. Configure the SX5 modem interface using the S tart -> Settings -> Control Panel -> Phone and Modem Options" -> Modems T ab 1 1. Select the 19200 bps Modem -> Click on Properties 12. Select the Modem tab. 13. Change the Maximum port speed to 1 15200 (19200 when faxing) and click OK.
14. Configure the USB or Serial port using the Control Panel -> System ->Hardware -> Device Manager -> Ports T ab 15. Select the port used for the SX5 and right click on it.
16. Click on the Port Settings tab. 17. Use these settings: Bits per second: 1 15200 (19200 when faxing) Data bits: 8 Parity: None S top bits: 1 Flow control: Hardware 18. Y ou may now proceed for transferring data and faxes by following the instructions in this manual.
WINDOWS 98 SETUP T o configure a Windows 98 computer and SX5 to work together , follow these steps. 1. Connect your computer and the SX5 with a T elular USB cable (part #1L01A043 or 81025901) or serial cable (part #1L01A042 or 81025801). 2. If you are using a USB cable, install the T elular USB drivers from the included CD.
6. Select the appropriate COM port and Maximum speed of 1 15,200 bps for data and 19200 bps for PC Fax. 7. Select the Connection tab. 8. Set Connection Preferences to Data bit s = 8, Parity = None and Stop bits = 1, then click “Advanced”.
9. Check the box for ‘Use Control Flow’ and then click on ‘Hardware (RTS/CTS) and then select ‘OK’. 8. Click on ‘OK’. Phonecell ® SX5 CDMA 29 User Manual.
9. Click on ‘Close’. 10. Y ou may now proceed for transferring data and faxes by following the instructions in this manual. See Sending/Receiving Faxes (page 31), Sending/Receiving 1X Dat a (page 32) or Sending/Receiving Circuit Switched Dat a (page 33) for details.
SENDING/RECEIVING A PC F AX A PC can send and receive faxes using the SX5. Y our account with your service provider must support circuit switched data transfer for the SX5’ s PC fax function to work. Note that you must use a PC to send faxes with the SX5; a fax machine connected directly to the SX5 will not work.
SENDING/RECEIVING 1X DA T A Check with your service provider to see if your account supports 1X data transfer . Choose the Port the SX5 Will Use for 1X Dat a 1. S tart by pressing MENU . 2. Select 6: Data Settings . 3. Select 1: Data Port Map . 4. Select RS-232 or USB and Press STO to save.
SENDING/RECEIVING CIRCUIT SWITCHED DA T A Check with your service provider to see if your account supports circuit switched data transfer . Choose the Port the SX5 Will Use for Circuit Switched Dat a 1. S tart by pressing MENU . 2. Select 6: Data Settings .
SX5 TROUBLESHOOTING T elephone Service is Not Working (Cannot make or receive calls) · Make sure the SX5 powered on properly . · Make sure any equipment that is externally connected to the SX5 is correctly connected. · T est any externally connected equipment on a known system to verify operation.
CONFORMANCE ST A TEMENTS FCC Part 15 Class B Compliance This Phonecell ® SX5 model has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
RF energy may affect improperly inst alled or inadequately shielded electronic operating and entertainment systems in motor vehicles. Check with the manufacturer or its represent ative to determine if these systems are adequately shielded from external RF energy .
W ARRANTY I. WHA T THIS W ARRANTY COVERS AND FOR HOW LONG: TELULAR CORPORA TION ('T elular") warrants to a distributor Buyer , or to a customer only if the customer is a Buyer directly from .
tomer normal use. (i) Costs and expenses, including without limitation handling, labor and trans- portation, incurred in returning Product for warranty service to T elular's Repair Center . (j) Repair , programming or servicing by someone other than T elular .
Phonecell ® SX5 CDMA 39 T echnical Manual NOTES.
Phonecell ® SX5 CDMA 40 T echnical Manual NOTES.
Phonecell ® SX5 CDMA 41 T echnical Manual NOTES.
©2004 T elular Corporation, all rights reserved. Part Number 56029702 647 North Lakeview Parkway V ernon Hills, Illinois 60061, USA T el: 847-247-9400 • Fax: 847-247-0021 E-mail: support@telular .
Ein wichtiger Punkt beim Kauf des Geräts Telular SX5P CDMA2000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Telular SX5P CDMA2000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Telular SX5P CDMA2000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Telular SX5P CDMA2000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Telular SX5P CDMA2000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Telular SX5P CDMA2000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Telular SX5P CDMA2000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Telular SX5P CDMA2000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Telular SX5P CDMA2000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
