Benutzeranleitung / Produktwartung 460L des Produzenten Teledyne
Zur Seite of 92
INSTRUCTION MANUAL MODEL 460L Nema Ozone Monitor 9480 CARROLL PARK DRI VE SAN DIEGO, CA 92121-52 01 USA Toll-free Phone: 800-324-5 190 Phone: 858-657-9 800 Fax: 858-657-9 816 Email: api-sales@teledyne.c om Website: http://www.teledyne-api.com/ 05012 REV.
TELEDYNE INSTRUMENTS HIGHLIGHTS Model 460L – NEMA Ozone Monitor Instruction Manual H-ii 05012 Rev D 22 January 2009 PRINTED DOCUMENTS ARE UNCONTROLLED DCN 5164 THIS PAGE IS INTENT IONALLY LEFT BLANK.
TELEDYNE INSTRUMENTS 460L Instruction Manual Safety Messages 05228 Rev B i DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED SAFETY MESSAGES Your safety and the safety of o thers is very im portant. We have provided many important sa fety messages in this manual.
TELEDYNE INSTRUMENTS Safety Messages 460L Instruction Manual ii 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 THIS PAGE IS INTENTIONALLY LEFT BLANK.
TELEDYNE INSTRUMENTS 460L Instruction Manual Table of Contents 05228 Rev B iii DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED TABLE OF CONTENTS 1. INTROD UCTION ............................................................................................
TELEDYNE INSTRUMENTS Table of Contents 460L Instruction Manual iv 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 9.1.1. Filter Repl acement P rocedure...........................................................................................
TELEDYNE INSTRUMENTS 460L Instruction Manual Table of Contents 05228 Rev B v DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED List of Figures Figure 3-1 M460L Front Co ver Lay out ...........................................................................
TELEDYNE INSTRUMENTS Table of Contents 460L Instruction Manual vi 05228 R ev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 LIST OF APPENDICES Appendix A – Spare Parts List Appendix B – List of Sc.
TELEDYNE INSTRUMENTS 460L Instruction Manual Introduction 05228 Rev B 1 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 1. INTRODUCTION 1.1. Preface Teledyne Instruments is pleased that you have purchased the Mo del 460L NEMA Ozone Monitor. Included is a full one-year warran ty (see Section 2.
TELEDYNE INSTRUMENTS Introduction 460L Instruction Manual 2 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 1.3. Using This Manual This manual has the followin g data structures: 1.0 Table of Contents: Outlines the conte nts of the manual i n the order the information is presented.
TELEDYNE INSTRUMENTS 460L Instruction Manual Introduction 05228 Rev B 3 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED interact with each ot her. A close reading of this section is inv aluable for underst anding the monitor’s operation.
TELEDYNE INSTRUMENTS Introduction 460L Instruction Manual 4 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 USER NOTES:.
TELEDYNE INSTRUMENTS 460L In structi on Manua l Spec ification s and Wa rranty 05228 Rev B 5 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 2. SPECIFICATIONS AND WARRANTY 2.
TELEDYNE INSTRUMENTS Specifications an d Warranty 460L Instruction Manual 6 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 2.2. Warranty WARRANTY POLICY (020 24D) Prior to shipment, T-API equipment is thorou ghly inspected and tested.
TELEDYNE INSTRUMENTS 460L Instruction Manual Getting Started 05228 Rev B 7 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 3. GETTING STARTED 3.1. Unpacking 1. Inspect the received packages for external sh ip ping damage. If damaged, please advise the shipper first, then Tele dyne Instruments.
TELEDYNE INSTRUMENTS Getting Started 460L Instruction Manual 8 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 CAUTION Never disconnect electronic cir cuit boards, wiring harnesses or electronic subassemblies while the unit is under power. 4.
TELEDYNE INSTRUMENTS 460L Instruction Manual Getting Started 05228 Rev B 9 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED A bsorption Tube Reference Scrubber UV Lamp Power Supply UV Lamp Power Connect o.
TELEDYNE INSTRUMENTS Getting Started 460L Instruction Manual 10 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 Table 3-1 460L Ventilation Cle arances AREA MINIMUM REQUIRED CLEARANCE Sides of the monitor 1 inch Above and below the monitor. 1 inch Figure 3-4 460L Mounting Hole Locations and Dimen sions 3.
TELEDYNE INSTRUMENTS 460L Instruction Manual Getting Started 05228 Rev B 11 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED NOTE The ozone delivery pr essure should be at ambient pressure +/- 5 PSIG. All tubing used shou ld be made of ozone r esistant material such as Stainl ess Steel, PTFE (Teflon ) or FEP.
TELEDYNE INSTRUMENTS Getting Started 460L Instruction Manual 12 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 3.4. Electrical Connections NOTE It is recommended that if multi- strand wires ar e used for the following electrical connections.
TELEDYNE INSTRUMENTS 460L Instruction Manual Getting Started 05228 Rev B 13 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 3.5. Signal I/O Connections All digital and analog signal I/ O connections are made vi a a 16-pin connector on the main board (See Figure 3-6 for the locati on of the connecto r.
TELEDYNE INSTRUMENTS Getting Started 460L Instruction Manual 14 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 3.5.2. Digital Status Outputs The 460L has six assigned digital status outputs for indicating error and operational status conditions of the monitor as well as the statu s of its O 3 concentration alarms (see Table 3-2).
TELEDYNE INSTRUMENTS 460L Instruction Manual Getting Started 05228 Rev B 15 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 3.5.3. Control Inputs Two digital control inputs are also available for use on the 460L. The control inputs are used for remote control of the 460L by a de vice such as a PL C.
TELEDYNE INSTRUMENTS Getting Started 460L Instruction Manual 16 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 Below each relay is a 3- pin connector that al lows the relay to be connec ted for either norma lly open or norma lly close d opera tion.
TELEDYNE INSTRUMENTS 460L Instruction Manual Getting Started 05228 Rev B 17 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 1 Located just below each rela y connector (see Figure 3-10) 2 N.O. = Normally Open operat ion. N.C. = Norma lly Closed opera tion.
TELEDYNE INSTRUMENTS Getting Started 460L Instruction Manual 18 05228 Rev B PRINTED DOCUMENTS ARE UN CONT ROLL ED DCN 5164 While the standard factory configuration is for RS- 232, the monitor’s serial port can be configured for either RS-232 or RS-485 (see Section 3.
TELEDYNE INSTRUMENTS 460L Instruction Manual Getting Started 05228 Rev B 19 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 7. Connect the appropriate type of ca ble to the 16 pin Signal I/O connector inside the analyzer. 8. A cable may be included with you i nstrument.
TELEDYNE INSTRUMENTS Getting Started 460L Instruction Manual 20 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 The Serial Port of the devi ce being used to communi cate with the 460L sho uld be configured as follow s: Table 3-6 Serial Port Configuration PARAMETER VALUE Baud Rate 9600 bps Data Bits 8 Stop Bits 1 Parity None 3.
TELEDYNE INSTRUMENTS 460L Instruction Manual Fr equently Asked Questions 05228 Rev B 21 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 4. FREQUENTLY ASKED QUESTIONS Q: What do I do if I smell Ozone and suspect a leak? A: Ensure that all the fi ttings are tight.
TELEDYNE INSTRUMENTS Frequently Asked Questions 460L Instruction Manual 22 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 USER NOTES:.
TELEDYNE INSTRUMENTS 460L Instruction Manual Optio nal Hardware and Soft ware 05228 Rev B 23 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 5. OPTIONAL HARDWARE AND SOFTWARE This section includes descriptions of the hardwa re and software options available for the 460L monitor.
TELEDYNE INSTRUMENTS Optional Hardware and Soft wa re 460L Instruction Manual 24 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 USER NOTES:.
TELEDYNE INSTRUMENTS 460L Instruction Manual Operating Instructio ns 05228 Rev B 25 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 6. OPERATING INSTRUCTIONS The 460L has been designed for simple and tr ouble-free operation. The sections below detail the operational features of the 460L.
TELEDYNE INSTRUMENTS Operating Instructio ns 460L Instruction Manual 26 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 6.2. Concentration Alarms There are two O 3 concentration alarms, HI and HI-HI . Both alarms are triggered when the measured O 3 concentration equals or rises abov e the set limit for t hat alarm.
TELEDYNE INSTRUMENTS 460L Instruction Manual Serial Communicatio ns 05228 Rev B 27 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 7. SERIAL COMMUNICATIONS The 460L comes equipped with a powe rful digital Seria l Communications Port th at can be used for Data Acquisiti on and for changing t he monitor’s co nfigurat ion.
TELEDYNE INSTRUMENTS Serial Communicatio ns 460L Instruction Manual 28 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 7.2. Serial Port Command Su mmary Table 7-1 below lists the commands availa ble and a sum mary of their function.
TELEDYNE INSTRUMENTS 460L Instruction Manual Serial Communicatio ns 05228 Rev B 29 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 7.3. Serial Port Command Reference 7.3.1. ALMACK SYNTAX <address>ALMACK<CR> DESCRIPTION Acknowledges any active con centration alarm an d clears them if possible For more inf ormation see Section 6.
TELEDYNE INSTRUMENTS Serial Communicatio ns 460L Instruction Manual 30 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 7.3.2. ALMSTAT SYNTAX <address>ALSTAT<CR> DESCRIPTION Returns the current status o f both of the concentratio n alarms.
TELEDYNE INSTRUMENTS 460L Instruction Manual Serial Communicatio ns 05228 Rev B 31 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 7.3.3. CZERO SYNTAX <address>CZERO<CR> DESCRIPTION Performs a zero calibration using gas sourced from the ozone gas inlet.
TELEDYNE INSTRUMENTS Serial Communicatio ns 460L Instruction Manual 32 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 7.3.4. DACSTEP SYNTAX <address>DACSTEP< CR> DESCRIPTION Puts the monitor i nto Analog Output setup mode.
TELEDYNE INSTRUMENTS 460L Instruction Manual Serial Communicatio ns 05228 Rev B 33 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 7.3.5. O 3 SYNTAX <address>O3<CR> DESCRIPTION Returns the current ozone conce ntration measured by t he monitor.
TELEDYNE INSTRUMENTS Serial Communicatio ns 460L Instruction Manual 34 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 7.3.6. SETADDR SYNTAX <address>SETADDR:<new_address><CR > DESCRIPTION Changes the communications a ddress to a ne w value.
TELEDYNE INSTRUMENTS 460L Instruction Manual Serial Communicatio ns 05228 Rev B 35 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 7.3.7. TDUMP SYNTAX <address>TDUMP<CR> DESCRIPTION This comm.
TELEDYNE INSTRUMENTS Serial Communicatio ns 460L Instruction Manual 36 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 7.3.8. TLIST SYNTAX <address>TLIST<CR> DESCRIPTION Returns a formatted, easy to read list of the p a rameters by name with the current values fo r each.
TELEDYNE INSTRUMENTS 460L Instruction Manual Serial Communicatio ns 05228 Rev B 37 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 7.3.9. VGET SYNTAX <address>VGET:<var_index><CR> DESCRIPTION Returns value of an internal conf iguration variable (VAR.
TELEDYNE INSTRUMENTS Serial Communicatio ns 460L Instruction Manual 38 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 7.3.10. VLIST SYNTAX <address>VLIST<CR> DESCRIPTION Returns a formatted, easy to read list of an in ternal configuration vari ables (VAR’s) and their current values.
TELEDYNE INSTRUMENTS 460L Instruction Manual Serial Communicatio ns 05228 Rev B 39 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 7.3.11. VSET SYNTAX <address>VSET:<var_index>, <new_value><CR> DESCRIPTION Sets value of an internal con figuration variabl e (VAR.
TELEDYNE INSTRUMENTS Serial Communicatio ns 460L Instruction Manual 40 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 EXAMPLE2 Command: 1VSET:6,1<CR> - Set CONC_UNITS VAR to ppm Respon.
TELEDYNE INSTRUMENTS 460L Instruction Manual Calibration 05228 Rev B 41 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 8. CALIBRATION 8.1. Zero Point calibration Variations in ambient condi tions, most .
TELEDYNE INSTRUMENTS Calibration 460L Instruction Manual 42 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 Where <address> is the network address of the M460M being ca librated. 929 is a special password allowing you to calibrate the analyzer.
TELEDYNE INSTRUMENTS 460L Instruction Manual Calibration 05228 Rev B 43 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 8. Enter the New Slope i nto the M460M’s memory enter i t in. Type: <address>VSET:<VAR Number>, <New Slope Value><CR> EXAMPLE 3VSET:16,1.
TELEDYNE INSTRUMENTS Calibration 460L Instruction Manual 44 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 5. The monitor will au tomatically generate t he nominal signal lev el by producing a 25% increment outpu t level on the current loop.
TELEDYNE INSTRUMENTS 460L Instruction Manual Maintenance 05228 Rev B 45 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 9. MAINTENANCE: 9.1. Replacing the Particulate Filter Element The 460L is equipped with a particul ate filter on the ozone inlet. Only Teledyne Instruments filter elements should be used.
TELEDYNE INSTRUMENTS Maintenance 460L Instruction Manual 46 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 9.1.2. Mounting the Particulate Filter Externally In applications where the 460L is.
TELEDYNE INSTRUMENTS 460L Instruction Manual Maintenance 05228 Rev B 47 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 9.2. Maintaining the Optional H 2 O Coalescing Filter 9.
TELEDYNE INSTRUMENTS Maintenance 460L Instruction Manual 48 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 9.2.2. Replacing the Coalescing Membrane The coalescing filter cont ains a replaceable Teflon ® coalescing membrane.
TELEDYNE INSTRUMENTS 460L Instruction Manual Maintenance 05228 Rev B 49 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 9.3. UV Lamp Replacement 1. Disconnect power from the monitor and open cover. 2. Loosen, but do not remov e, the two la mp set-screws (see Figure 9-5 below).
TELEDYNE INSTRUMENTS Maintenance 460L Instruction Manual 50 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 9.4. Cleaning Exterior Surfaces of the 460L If necessary, the exterior surfaces of the 460L can be cleaned with a damp cloth. Do not attempt to clean any of the other surfaces of the monitor.
TELEDYNE INSTRUMENTS 460L Instruction Manual Theory of Operation 05228 Rev B 51 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 10. THEORY OF OPERATION 10.
TELEDYNE INSTRUMENTS Theory of Operation 460L Instruction Manual 52 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 To solve this equation for C , the concentration of the absorbing gas (in t.
TELEDYNE INSTRUMENTS 460L Instruction Manual Theory of Operation 05228 Rev B 53 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED beam is only required to make pas s through th e Absorption Tube. Therefore no complex mirror system is needed to lengthen the effective path b y bouncing the beam back a nd forth.
TELEDYNE INSTRUMENTS Theory of Operation 460L Instruction Manual 54 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 The Measurement / Reference Cycle consists o f: Table 10-1 Measurem ent / Reference Cycle CYCLE STATUS DURATION ACTIVITY VALVE STATE (FIG.
TELEDYNE INSTRUMENTS 460L Instruction Manual Theory of Operation 05228 Rev B 55 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 10.2. Pneumatic Theory of Operation 10.
TELEDYNE INSTRUMENTS Theory of Operation 460L Instruction Manual 56 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 10.2.3. Optional Sample Conditioning The source air measured by the 46 0L needs to be as dry as possible. Significant amounts of liquid or vaporous water present in the s ource gas ca n fo ul the measurement cell optics.
TELEDYNE INSTRUMENTS 460L Instruction Manual Theory of Operation 05228 Rev B 57 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED To provide a dry purge gas for the outer side of the Nafion ® tube, the 460L returns the dried O 3 free air from the measurement cell and O 3 destruct to the outer tube (see Figure 10-4).
TELEDYNE INSTRUMENTS Theory of Operation 460L Instruction Manual 58 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 10.3. Electronic Theory of Operation Sensor Module Main Board Status Output.
TELEDYNE INSTRUMENTS 460L Instruction Manual Theory of Operation 05228 Rev B 59 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 10.3.2. O 3 Sensor Module The heart of the 460 Monitor is the O 3 sensor module.
TELEDYNE INSTRUMENTS Theory of Operation 460L Instruction Manual 60 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 Gas Pressure Sensor: This absolute pressure sensor m easures the gas pressure i n the measurement cell upstream of the Pump.
TELEDYNE INSTRUMENTS 460L Instruction Manual Theory of Operation 05228 Rev B 61 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 10.3.3. CPU Board In addition to being responsible for all I/O f unctions a.
TELEDYNE INSTRUMENTS Theory of Operation 460L Instruction Manual 62 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 and available at the STATUS COM pin of J2 on the main board (see Figure 3-7). This pin is normally connected to the input ground of the external device.
TELEDYNE INSTRUMENTS 460L Instruction Manual Theory of Operation 05228 Rev B 63 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 10.3.5. Power Distribution The 460L operates on 90 to 260 V AC power at eith er 50Hz or 60Hz.
TELEDYNE INSTRUMENTS Theory of Operation 460L Instruction Manual 64 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 UV LA MP PO WER SUPPL Y: Using +1 2 VDC supplied by the main pow er supply, this assembly generates the 30 kHz AC voltage for the mo nitor’s mercury vapor UV lamp.
TELEDYNE INSTRUMENTS 460L Instruction Manual Troubleshooting 05228 Rev B 65 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 11. TROUBLESHOOTING This chapter gives guidelines for diagnosing sy stem and sensor malfunction s using the five digital Status Outputs provided by the 46 0L.
TELEDYNE INSTRUMENTS Troubleshooting 460L Instruction Manual 66 05228 Rev B PRINTED DOCUMENTS ARE UN CONT ROLL ED DCN 5164 The O3 sensor is not responding to CPU reques ts for data. This could represent a variety of electronic problems with the sensor modu l e or internal communication between the CPU and the sensor module.
TELEDYNE INSTRUMENTS 460L Instruction Manual Troubleshooting 05228 Rev B 67 DCN 5164 PRINTED DOCUMENTS ARE UN CONT ROLL ED Table 11-2 Stat us LED / Output Trouble s hooting Truth Table SENSOR OK INVALID READING LAMP LOW ACTIONS 1 0 0 Normal operation, no action required.
TELEDYNE INSTRUMENTS Troubleshooting 460L Instruction Manual 68 05228 Rev B PRINTED DOCUMENTS ARE UN CONT ROLL ED DCN 5164 11.4. Technical Assistance If this addendum and its tr ouble-shooting / repai.
TELEDYNE INSTRUMENTS 460L Instruction Manual A Primer on Electro-Static Disc harge 05228 Rev B 69 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 12. A PRIMER ON ELECTRO-STATIC DISCHARGE Teledyne Instrum.
TELEDYNE INSTRUMENTS A Primer on Electro-Static Dischar ge 460L Instruction Manual 70 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 Table 12-1 Static Generation Voltages for Typic al Activi.
TELEDYNE INSTRUMENTS 460L Instruction Manual A Primer on Electro-Static Disc harge 05228 Rev B 71 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED Any time a charged surface (including the human body) discharges to a device. Even simple contact of a fing er to the leads of a sensitive device or assembly can allow enough discharge to cause damage.
TELEDYNE INSTRUMENTS A Primer on Electro-Static Dischar ge 460L Instruction Manual 72 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 other things, like you a nd your clothing, from discharging through the instrumen t and damaging it.
TELEDYNE INSTRUMENTS 460L Instruction Manual A Primer on Electro-Static Disc harge 05228 Rev B 73 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED While this layer may equalizes any charges th at occur across the whole bag, it does not prevent the build-up of static charges.
TELEDYNE INSTRUMENTS A Primer on Electro-Static Dischar ge 460L Instruction Manual 74 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 This will allow any charges you are carrying t o bleed away through the ground conn ection of the workstation and preven t discharges due to fi eld effects and inductio n from occurring.
TELEDYNE INSTRUMENTS 460L Instruction Manual A Primer on Electro-Static Disc harge 05228 Rev B 75 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 5. Seal the container. If usi ng a bag, fold the end over and fastening it with a n ti-ESD tape. Folding the open end over isol ates the component(s) inside from the effects of static fields.
TELEDYNE INSTRUMENTS A Primer on Electro-Static Dischar ge 460L Instruction Manual 76 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 12.4.2.5.
TELEDYNE INSTRUMENTS 460L Instruction Manual A Primer on Electro-Static Disc harge 05228 Rev B 77 DCN 5164 PRINTED DOCUMENTS ARE UN CONTROLLED 4. Seal the container. If usi ng a bag, fold the end over and fastening it with a n ti-ESD tape. Folding the open end over isol ates the component(s) inside from the effects of static fields.
TELEDYNE INSTRUMENTS 460L Instruction Manual Spare Parts List 78 05228 Rev B PRINTED DOCUMENTS ARE UN CONTROLLED DCN 5164 USER NOTES:.
M460L Instruction Manual Appendix A - Spare Parts list Appendix A - Spare Parts list • 05128 – Spar e Parts List M460L 05229 Rev B A-1.
Appendix A - Spare Parts list M460L Instruction Manual A-2 05229 Rev B.
M460L Spare Parts List Part Number Description 025710100 PCA, UV DETECTOR PREAMP, M454/M460 030500400 OVERLAY, FRONT PANEL, O3 SENSOR, M460L 031680100 PCA, FRONT PANEL, M454 PRODUCTS 034920000 PCA, EX.
THIS PAGE IS INTENTIONALLY LEFT BLANK.
460L Instruction Manual Append ix B – Electronic Schematics Appendix B – Electronic Schematics Table B-1 M460L List of Electr onic Sc hematics DOCUMENT # DESCRIPTION 03169 PCA, FRONT PANEL DISPLAY.
Appendix B – Electronic Schema tics 460L Instruction Manual B-2 05230 Rev A.
Ein wichtiger Punkt beim Kauf des Geräts Teledyne 460L (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Teledyne 460L noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Teledyne 460L - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Teledyne 460L reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Teledyne 460L erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Teledyne 460L besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Teledyne 460L verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Teledyne 460L. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Teledyne 460L gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
