Benutzeranleitung / Produktwartung SSC091 des Produzenten Sylvania
Zur Seite of 32
9-INCH COLOR TV/VCR SSC091 O WNER’S MANU AL As an E NERGY S TAR Partner, our company has determined that this product meets the E NERGY S TAR guidelines for energy efficiency.
1.Read instructions- All the safety and operating instructions should be read before the appliance is operated. 2.Retain Instructions- The safety and operating instructions should be retained for future reference. 3.Heed W arnings -All warnings on the appliance and in the operating instructions should be adhered to.
- 3 - EN 1A19 13.Outdoor Antenna gr ounding- If an outside antenna or cable system is connected to the TV/VCR, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFP A No.
A V OID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE This equipment has been tested and found to com- ply with the limits for a Class B digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- 5 - EN 1A19 T ABLE OF CONTENTS A NOTE ABOUT RECYCLING This product’ s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
- 6 - EN 1A19 FEA TURES • I nfrared remote control • Dew Sensor – Indicates that moisture condensation may occur inside the TV/VCR. • Bilingual on screen menu display selectab le in English or Spanish • Real time counter – This shows the elapsed recording or playback time in hours, minutes, and seconds.
- 7 - EN 1A19 OPERA TING CONTROLS AND FUNCTIONS - TV/VCR FR ONT P ANEL - 5 PO WER button – Press to turn TV/VCR on and off. Press to activate timer recording. 6 ST OP button – Press to stop the tape motion. EJECT button – Press in the Stop mode to remove tape from TV/VCR.
- 8 - EN 1A19 - REAR VIEW - 27 28 29 ANT . AC 120V DC 13.2V 10 REC button – Press for manual recording. O TR button – Activates One T ouch Recording. (only on the TV/VCR) 11 V OLUME X X / Y Y buttons – Adjust the volume level. 12 CHANNEL K / L buttons – Press to select the desired channels for viewing or recording.
- 9 - EN 1A19 ANTENNA/CABLE CONNECTIONS DIPOLE ANTENNA HOOK UP 1. Push the stem of the Dipole Antenna (accessory) into the hole for antenna at the back of TV/VCR. 2. Connect the flat twin-lead cable from the Dipole Antenna to the 300/75 ohm Matching Adapter (accessory).
- 10 - EN 1A19 INST ALLING THE BA TTERIES 1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow . 2)Insert 2 “AA” penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings.
- 11 - EN 1A19 SET UP FOR USE Y ou can program the tuner to scan all the channels you receive in your area. NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3).
- 12 - EN 1A19 2 Set “ A UT O CLOCK ” to [ON] Press the F .FWD/ B or REW/ s button repeatedly until [ON] appears. 3 Enter the channel number f or the PBS station Press the PLA Y/ K or STOP/ L but- ton to point to “AUTO CLOCK CH”. Then press the F .
- 13 - EN 1A19 CHANNEL SET UP AGAIN Make sure ... • Press the POWER button to turn on the TV/VCR. 1 Select “ CHANNEL SET UP ” Press the MENU button on the remote control. Press the PLA Y/ K or STOP/ L but- ton to point to “CHANNEL SET UP”. Then, press the F .
TV OPERA TION W A TCHING A TV PROGRAM 1 T urn on the TV/VCR Press the POWER button to turn on the TV/VCR. 2 Select the channel number Press the CHANNEL K or L button to select your desired channel number or press the number buttons on the remote control.
- 15 - EN 1A19 REW/ s F .FWD/ B BRIGHT to decrease to increase brightness brightness CONTRAST to decrease to increase contrast contrast COLOR to pale to brilliant TINT to purple to green SHARPNESS to soft to clear GAME MODE This function enables you to decrease the TV screen contrast and making it suitable for use with a TV GAME.
- 16 - EN 1A19 PLA YBACK NORMAL PLA YBACK Make sure ... • TV/VCR power must be turned on. 1 Insert a prerecorded tape If the erase-protection tab has been removed, the TV/VCR will start playback automatically . 2 T o begin playback Press the PLA Y button.
- 17 - EN 1A19 PICTURE SEARCH This feature is very useful in finding or skipping over a particular scene on a tape. In this mode, the sound will be muted. 1)Y ou may view a video tape at a high speed in either a forward or reverse direction by pressing the F .
- 18 - EN 1A19 • T racking adjustment will be set automatically (Digital T racking function) when you start play- back. • However when playing pre-recorded tapes or tapes recorded on units other than your own, noise lines (black and white streaks) may appear on the play- back picture.
- 19 - EN 1A19 Make sure ... • TV/VCR power must be turned on. • Insert a cassette tape with its erase prevention tab in place. (If necessary , rewind or fast forward the tape to the point at which you want to begin recording.) NOTE: This unit will ONL Y record and view the same channel.
- 20 - EN 1A19 3 Begin O TR Press the REC/OTR button on the TV/VCR as many times as needed. The recording length will be deter- mined by the number of times you press the REC/OTR button. Each additional push will increase the recording time by 30 minutes.
- 21 - EN 1A19 For every day recording : T o r ecord a TV program at the same time on the same channel every day . (Example: Monday thr ough Sunday) Press the STOP/ L (down) button until “EVR Y DA Y” appears. Then, press the F .FWD/ B but- ton. For weekly recording : T o r ecord a TV program at the same time on the same channel every week.
- 22 - EN 1A19 TO CANCEL AN AUTOMA TIC TIMER RECORDING • After setting a program; 1)Press the POWER button. 2)Repeat steps [1] ~ [2] on page 20 and select a program you want to cancel. 3)Press the T -PROG. CLEAR button. 4)Press the MENU button on the remote control to return to TV mode.
- 23 - EN 1A19 3 Set wake up time Press the PLA Y/ K or STOP/ L but- ton until to point to “TIME”. Press the F .FWD/ B or REW/ s button until your desired wake up time appears. Each additional push will increase (or decrease) the time by 10 minutes.
- 24 - EN 1A19 CABINET CLEANING • W ipe the front panel and other exterior surfaces of the TV/VCR with a soft cloth immersed in luke- warm water and wrung dry . • Never use a solvent or alcohol. Do not spray insec- ticide liquid near the TV/VCR. Such chemicals may cause damage and discoloration to the exposed surfaces.
- 25 - EN 1A19 TROUBLESHOOTING GUIDE If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR, locate the PROBLEM in the left column below . Check the corresponding CORRECTIVE ACTION column to remedy the problem.
- 26 - EN 1A19 GENERAL SPECIFICA TIONS CR T : 9 inch in-line gun, 90˚ deflection tube T elevision system : NTSC-M V ideo Heads : Rotary two-head T ape width : 1/2 inch T ape speed SP : 33.
- 27 - ES 1A23 1 T oma de entrada de audio (A UDIO)– Conéctela a la toma de salida de audio de su equipo de audio, videocámara u otra videograbadora. 2 T oma de entrada de vídeo (VIDEO)– Conéctela a la toma de salida de vídeo de su videocámara u otra videograbadora.
- 28 - ES 1A23 11 Botones de volumen (V OLUME X X / Y Y )– Ajustan el nivel del volumen. 12 Botones de canales (CHANNEL K / L )– Púlselos para selec- cionar los canales deseados para ver o grabar . Se puede mostrar el menú principal en la pantalla del televisor pulsando repetidamente este botón del televisor/videograbadora.
- 29 - ES 1A23 CONEXION DE LA ANTENA BIPOLAR 1. Introduzca la varilla de la antena bipolar (accesorio) en el orifi- cio destinado para la antena, en la parte trasera de la TV/VCR. 2. Conecte el cable bifilar plano de la antena bipolar al adaptador de acoplo (accesorio) de 300/75 ohm.
- 30 - ES 1A23 1) Abra la tapa del compartimiento de las pilas del mando a distancia presionándola en el sentido de la flecha. 2) Inserte 2 pilas tamaño “AA” en el compartimiento de las pilas, en el sentido indicado por las marcas de polaridad (+/-).
- 31 - ES 1A23 1) Conecte el extremo más prqueño del cordón de CA al conector de CA de 120V en la parte posterior de la TV/VCR. Luego, enchufe el otro extremo enun tomacorriente normal de CA. NOT AS: • Dede desconectar de la TV/VCR el cordón para la batería del automóvil antes de usar la alimentación de CA.
LIMITED W ARRANTY FUNAI CORP . will repair this SYL V ANIA product, free of charge in the USA in the event of defect in materials or workmanship as follows: DURA TION: P ARTS: FUNAI CORP . will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase.
Ein wichtiger Punkt beim Kauf des Geräts Sylvania SSC091 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sylvania SSC091 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sylvania SSC091 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sylvania SSC091 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sylvania SSC091 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sylvania SSC091 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sylvania SSC091 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sylvania SSC091. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sylvania SSC091 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
