Benutzeranleitung / Produktwartung MBD-H8DMR-82-B des Produzenten Supermicro
Zur Seite of 78
H8DMR-82 H8DMR-i2 USER’S MANUAL Revision 1.0d S UPER ®.
Manual Revision 1.0d Release Date: March 13, 2009 The information in this User ’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inac.
Preface iii Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the H8DMR-82/H8DMR-i2 serverboard.
H8DMR-82/H8DMR-i2 User ’s Manual T able of Contents Preface About This Manual ...................................................................................................... iii Manual Organization ............................................
v T able of Contents USB Ports .............................................................................................. 2-1 1 USB Headers ......................................................................................... 2-12 Serial Ports .
H8DMR-82/H8DMR-i2 User ’s Manual 2-10 Enabling SA T A RAID .................................................................................... 2-24 2-1 1 Installing Additional Drivers ................................................................
Chapter 1: Introduction 1-1 Chapter 1 Introduction 1-1 Overview Checklist Congratulations on purchasing your computer serverboard from an acknowledged leader in the industry . Our boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance.
1-2 H8DMR-82/H8DMR-i2 User ’s Manual Contacting Supermicro Headquarters Address: Super Micro Computer , Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.
Chapter 1: Introduction 1-3 Note: The H8DMR-82 is pictured. The H8DMR-i2 shares the same layout but with no SCSI components, connectors or jumpers. Figure 1-1.
1-4 H8DMR-82/H8DMR-i2 User ’s Manual Notes: 1. Jumpers not indicated are for test purposes only . 2. The H8DMR-i2 has the same layout as the H8DMR-82 but with no SCSI compo- nents, connectors or jumpers.
Chapter 1: Introduction 1-5 H8DMR-82/H8DMR-i2 Quick Reference Jumpers Description Default Setting J3P 3rd Power Fail Detect En/Dis Closed (Enabled) JBT1 CMOS Clear See Section 2-7 JCF1 Compact Flash M.
1-6 H8DMR-82/H8DMR-i2 User ’s Manual Serverboard Features CPU • Single or dual AMD Opteron 2000 Series Socket F type 64-bit processors Memory • Eight dual/single channel DIMM slots supporting up to 64 GB of DDR2-667 /533/400 registered ECC SDRAM Note: Memory capacities are halved for single CPU systems.
Chapter 1: Introduction 1-7 ACPI Features • Slow blinking LED for suspend state indicator • BIOS support for USB keyboard • Main switch override mechanism • Internal/external modem ring-on Onb.
1-8 H8DMR-82/H8DMR-i2 User ’s Manual Figure 1-3. nVidia MCP55 Pro/NEC uPD720400 Chipset: System Block Diagram Note: This is a general block diagram and may not exactly represent the features on your serverboard. See the previous pages for the actual speci fi cations of your serverboard.
Chapter 1: Introduction 1-9 1-2 Chipset Overview The H8DMR-82/H8DMR-i2 serverboard is based on the nVidia MCP55 Pro/NEC uPD720400 chipset. The nV idia MCP55 Pro functions as Media and Communica- tions Processor (MCP) and the NEC chip as a PCI-X T unnel.
1-10 H8DMR-82/H8DMR-i2 User ’s Manual 1-3 PC Health Monitoring This section describes the PC health monitoring features of the H8DMR-82/H8DMR- i2. The serverboard has an onboard System Hardware Monitor chip that supports PC health monitoring. Onboard V oltage Monitors for two CPU cores, Hyper T ransport (1.
Chapter 1: Introduction 1-1 1 1-4 Power Con fi guration Settings This section describes the features of your serverboard that deal with power and power settings. Slow Blinking LED for Suspend-State Indicator When the CPU goes into a suspend state, the chassis power LED will start blinking to indicate that the CPU is in suspend mode.
1-12 H8DMR-82/H8DMR-i2 User ’s Manual 1-5 Power Supply As with all computer products, a stable power source is necessary for proper and reliable operation. It is even more important for processors that have high CPU clock rates. The H8DMR-82/H8DMR-i2 accommodates 12V A TX power supplies.
Chapter 1: Introduction 1-13 1-6 Super I/O The disk drive adapter functions of the Super I/O chip include a fl oppy disk drive controller that is compatible with industry standard 82077/765, a data s.
1-14 H8DMR-82/H8DMR-i2 User ’s Manual Notes.
Chapter 2: Installation 2-1 Chapter 2 Installation 2-1 Static-Sensitive Devices Electrostatic Discharge (ESD) can damage electronic com ponents. T o prevent dam- age to your system board, it is important to handle it very carefully . The following measures are generally suf fi cient to protect your equipment from ESD.
2-2 H8DMR-82/H8DMR-i2 User's Manual ! 2-2 Processor and Heatsink Installation Installing the Processor (install to the CPU#1 socket fi rst) 1. Begin by removing the cover plate that protects the CPU. Lift the lever on CPU socket #1 until it points straight up.
Chapter 2: Installation 2-3 3. Align pin 1 of the CPU with pin 1 of the socket. Once aligned, carefully place the CPU into the socket. Do not drop the CPU on the socket, move the CPU horizontally or vertically or rub the CPU against the socket or against any pins of the socket, which may damage the CPU and/or the socket .
2-4 H8DMR-82/H8DMR-i2 User's Manual Installing the Heatsink The use of active type heatsinks (except for 1U systems) are recommended. Con- nect the heatsink fans to the appropriate fan headers on the serverboard. T o install the heatsinks, please follow the installation instructions included with your heatsink package (not included).
Chapter 2: Installation 2-5 2-3 Mounting the Serverboard into a Chassis All serverboards and motherboards have standard mounting holes to fi t dif ferent types of chassis. Make sure that the locations of all the mounting holes for both the serverboard and the chassis match.
2-6 H8DMR-82/H8DMR-i2 User's Manual Figure 2-2. Side and T op Views of DDR Installation T o Install: Insert module vertically and press down until it snaps into place. The release tabs should close - if they do not you should close them yourself.
Chapter 2: Installation 2-7 Populating Memory Banks for 128-bit Operation CPU1 DIMM1A CPU1 DIMM1B CPU1 DIMM2A CPU1 DIMM2B CPU2 DIMM1A CPU2 DIMM1B CPU2 DIMM2A CPU2 DIMM2B XX XX XX XX XX XX XXXX XXXX XX.
2-8 H8DMR-82/H8DMR-i2 User's Manual 2-5 I/O Port and Control Panel Connections The I/O ports are color coded in conformance with the PC99 speci fi cation to make setting up your system easier . See Figure 2-3 below for the colors and locations of the various I/O ports.
Chapter 2: Installation 2-9 2-6 Connecting Cables A TX Power Connector The primary A TX power supply con- nector (JPW1) meets the SSI (Super- set A TX) 20-pin speci fi cation. Refer to the table on the right for the pin de fi nitions of the A TX power connec- tor .
2-10 H8DMR-82/H8DMR-i2 User's Manual Overheat/Fan Fail LED Connect an LED to the OH connection on pins 7 and 8 of JF1 to provide ad- vanced warning of chassis overheat- ing. Refer to the table on the right for pin de fi nitions and status indicators.
Chapter 2: Installation 2-1 1 Power Fail LED The Power Fail LED connection is located on pins 5 and 6 of JF1. Refer to the table on the right for pin de fi ni- tions.
2-12 H8DMR-82/H8DMR-i2 User's Manual Fan Headers The H8DMR-82/H8DMR-i2 has fi ve- fan headers, which are designated F AN1 through F AN5. See the table on the right for pin de fi nitions. Note: when using active heatsinks (those with fans), connect the heatsink fans to the nearest fan header .
Chapter 2: Installation 2-13 A TX PS/2 Keyboard and PS/2 Mouse Ports The A TX PS/2 keyboard and the PS/2 mouse ports are located on the I/O backplane (see Figure 2-3).
2-14 H8DMR-82/H8DMR-i2 User's Manual W ake-On-LAN The W ake-On-LAN header is desig- nated JWOL. See the table on the right for pin de fi nitions. Y ou must have a LAN card with a W ake-On-LAN connector and cable to use the W ake- On-LAN feature.
Chapter 2: Installation 2-15 3rd Power Supply Alarm Reset Header Connect JAR to the alarm reset but- ton on your chassis (if available) or to a microswitch to allow you to turn off the alarm that sounds when a power supply module fails. See the table on the right for pin de fi nitions.
2-16 H8DMR-82/H8DMR-i2 User's Manual 2-7 J u m p e r S et t i n g s Explanation of Jump ers T o mo dif y th e ope rati on of t he ser verboard, jumpers can be used to choose between optional se tt ings. Jum per s c reate s hor ts b et ween t wo p in s to ch a n g e th e fu nc ti o n of th e c onne ct or .
Chapter 2: Installation 2-17 CMOS Clear JBT1 is used to clear CMOS and will also clear any passwords. Instead of pins, this jumper consists of contact pads to prevent accidentally clearing the contents of CMOS. T o clear CMOS, 1) First power down the system and unplug the power cord(s).
2-18 H8DMR-82/H8DMR-i2 User's Manual PCI-X Slot Freq. Select Jumpers JPX1A and JPX1B on the H8DMR-82/H8DMR-i2 can be used to change the speed of PCI-X slots 6 and PCI-X slot 7, respectively .
Chapter 2: Installation 2-19 SCSI Con troll er Ena ble / Di sa bl e (H8 DM R- 82 o nly) J u m pe r J P A 1 i s u s e d t o e n a b l e o r d i s - abl e th e onb oar d SC SI c ont rol ler . The default setting is on pins 1-2 to enable SCSI. Se e the t ab le o n ri ght fo r jumper settings.
2-20 H8DMR-82/H8DMR-i2 User's Manual 2-8 Onboard Indicators LAN1/LAN2 LEDs The Ethernet ports (located beside the VGA port) have two LEDs. On each Gb LAN port, one LED indicates activity when blinking while the other LED may be amber or off to indicate the speed of the connection.
Chapter 2: Installation 2-21 2-9 Floppy , IDE, SA T A and SCSI Drive Connections Use the following information to connect the fl oppy and hard disk drive cables. The fl oppy disk drive cable has seven twisted wires. A red mark on a wire typically designates the location of pin 1.
2-22 H8DMR-82/H8DMR-i2 User's Manual IDE Connector There are no jumpers to con fi g- ure the onboard JIDE1 connec- tor . See the table on the right for pin de fi nitions.
Chapter 2: Installation 2-23 Ultra320 SCSI Drive Connectors Pin De fi nitions (JA1, JB1) Pin# De fi nition Pin # De fi nition 1 +DB (12) 35 -DB (12) 2 +DB (13) 36 -DB (13) 3 +DB (14) 37 -DB (14) 4 .
2-24 H8DMR-82/H8DMR-i2 User's Manual 2-10 Enabling SA T A RAID Now that the hardware is set up, you must now install the operating system and the SA T A RAID drivers, if you wish to use RAID with your SA T A drives.
Chapter 2: Installation 2-25 2. Use the arrow keys to move to Advanced > Floppy/IDE/SA T A Con fi guration > nVidia RAID Setup and press the <Enter> key . Once in the submenu, enable the "nVidia RAID Function" setting, which will cause the SA T A0/1/2 Primary/Secondary settings to appear .
2-26 H8DMR-82/H8DMR-i2 User's Manual Figure 2-5. Driver/T ool Installation Display Screen Click the icons showing a hand writing on paper to view the readme fi les for each item. Click the computer icons to the right of these items to install each item (from top to the bottom) one at a time.
3-1 Chapter 3: T roubleshooting Chapter 3 T roubleshooting 3-1 T roubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘T echnical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter .
3-2 H8DMR-82/H8DMR-i2 User's Manual NOTE If you are a system integrator , V AR or OEM, a POST diagnostics card is recommended. For I/O port 80h codes, refer to App. B. Memory Errors 1. Make sure that the DIMM modules are properly and fully installed.
3-3 Chapter 3: T roubleshooting 3. If you still cannot resolve the problem, include the following information when contacting us for technical support: Serverboard model and PCB revision number .
3-4 H8DMR-82/H8DMR-i2 User's Manual Question: Why can't I turn off the power using the momentary power on/off switch? Answer: The instant power of f function is controlled in BIOS by the Power But- ton Mode setting.
Chapter 4: BIOS 4-1 Chapter 4 BIOS 4-1 Introduction This chapter describes the AMIBIOS™ Setup utility for the H8DMR-82/H8DMR-i2. The AMI ROM BIOS is stored in a fl ash chip and can be easily upgraded using a fl oppy disk-based program.
4-2 H8DMR-82/H8DMR-i2 User ’s Manual 4-2 Main Menu When you fi rst enter AMI BIOS Setup Utility , you will see the Main Menu screen. Y ou can always return to the Main Menu by selecting the Main tab on the top of the screen with the arrow keys.
Chapter 4: BIOS 4-3 Advanced ACPI Con fi guration ACPI V ersion Features Use this setting the determine which ACPI version to use. Options are ACPI v1.0 , ACPI v2.0 and ACPI v3.0. ACPI APIC Support Determines whether to include the ACPI APIC table pointer in the RSDT pointer list.
4-4 H8DMR-82/H8DMR-i2 User ’s Manual Floppy/IDE/SA T A Con fi guration Onboard Floppy Controller Use this setting to Enable or Disable the onboard fl oppy controller . Floppy A Move the cursor to these fi elds via up and down <arrow> keys to select the fl oppy type.
Chapter 4: BIOS 4-5 Primary IDE Master/Slave Highlight one of the items above and press <Enter> to access the submenu for that item. T ype Select the type of device connected to the system. The options are Not Installed, Auto , CDROM and ARMD. LBA/Large Mode LBA (Logical Block Addressing) is a method of addressing data on a disk drive.
4-6 H8DMR-82/H8DMR-i2 User ’s Manual DMA Mode Selects the DMA Mode. Options are SWDMA0, SWDMA1, SWDMA2, MWDMA0. MDWDMA1, MWDMA2, UDMA0. UDMA1, UDMA2, UDMA3, UDMA4 and UDMA5.
Chapter 4: BIOS 4-7 PIO Mode PIO (Programmable I/O) mode programs timing cycles between the IDE drive and the programmable IDE controller . As the PIO mode increases, the cycle time decreases. The options are Auto , 0, 1, 2, 3, and 4. Select Auto to allow AMI BIOS to auto detect the PIO mode.
4-8 H8DMR-82/H8DMR-i2 User ’s Manual PCI/PnP Con fi guration Load Onboard LAN Option ROM Use this setting to Enable or Disable the onboard option ROM. Clear NVRAM Select Y es to clear NVRAM during boot-up. The options are Y es and No . Plug & Play OS Select Y es to allow the OS to con fi gure Plug & Play devices.
Chapter 4: BIOS 4-9 Advanced Chipset Control NorthBridge Con fi guration Memory Con fi guration Memclock Mode This setting determines how the memory clock is set. Auto has the memory clock by code and Limit allows the user to set a standard value.
4-10 H8DMR-82/H8DMR-i2 User ’s Manual DRAM Scrub Redirect Allows system to correct DRAM ECC errors immediately , even with background scrubbing on. Options are Enabled and Disabled . DRAM BG Scrub Corrects memory errors so later reads are correct. Options are Dis- abled and various times in nanoseconds and microseconds.
Chapter 4: BIOS 4-1 1 Processor Clock Options This submenu lists CPU information and the following settings: MTRR Mapping This determines the method used for programming CPU MTRRs when 4 GB or more memory is present.
4-12 H8DMR-82/H8DMR-i2 User ’s Manual Serial Port 2 Mode T ells BIOS which mode to select for serial port 2. The options are Normal , IrDA and ASKIR. DMI Event Logging View Event Log Highlight this item and press <Enter> to view the contents of the event log.
Chapter 4: BIOS 4-13 Hardware Health Con fi guration CPU Overheat Alarm Use the "+" and "-" keys to set the CPU temperature threshold to between 65 o and 90 o C. When this threshold is exceeded, the overheat LED on the chas- sis will light up and an alarm will sound.
4-14 H8DMR-82/H8DMR-i2 User ’s Manual F AN1 Speed through F AN5 Speed The speeds of the onboard fans (in rpm) are displayed here. F AN1 Speed Down Time Use the "+" and "-" keys to set the fan speed time interval of the ramp down.
Chapter 4: BIOS 4-15 IPMI Con fi guration View BMC System Event Log Pressing the Enter key will open the following settings. Use the "+" and "-" keys to navigate through the system event log. Clear BMC System Event Log Selecting this and pressing the Enter key will clear the BMC system event log.
4-16 H8DMR-82/H8DMR-i2 User ’s Manual Startup Delay Use this setting to Enable or Disable the startup delay . Event Message for PEF Action Use this setting to Enable or Disable event messages for a PEF action. BMC W atch Dog Timer Action This setting is used to set the W atch Dog function.
Chapter 4: BIOS 4-17 CD/DVD Drives This feature allows the user to specify the Boot sequence from available CD/DVD drives. OS Installation Change this setting if using a 64-bit Linux operating system. The available options are Other and 64-bit Linux 2.
4-18 H8DMR-82/H8DMR-i2 User ’s Manual 4-6 Exit Menu Select the Exit tab from AMI BIOS Setup Utility screen to enter the Exit BIOS Setup screen. Save Changes and Exit When you have completed the syst.
Appendix A BIOS Error Beep Codes During the POST (Power-On Self-T est) routines, which are performed each time the system is powered on, errors may occur . Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process.
A-2 H8DMR-82/H8DMR-i2 User ’s Manual Notes.
B-1 Appendix B: BIOS POST Checkpoint Codes Appendix B BIOS POST Checkpoint Codes When AMIBIOS performs the Power On Self T est, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, diagnostic equipment can be attached to the computer to read I/O port 0080h.
B-2 H8DMR-82/H8DMR-i2 User ’s Manual Checkpoint Code Description E0h The onboard fl oppy controller if available is initialized. Next, beginning the base 512 KB memory test. E1h Initializing the interrupt vector table next. E2h Initializing the DMA and Interrupt controllers next.
B-3 Appendix B: BIOS POST Checkpoint Codes Checkpoint Code Description 03h The NMI is disabled. Next, checking for a soft reset or a power on condition. 05h The BIOS stack has been built. Next, disabling cache memory . 06h Uncompressing the POST code next.
B-4 H8DMR-82/H8DMR-i2 User ’s Manual Checkpoint Code Description 25h Interrupt vector initialization is done. Clearing the password if the POST DIAG switch is on. 27h Any initialization before setting video mode will be done next. 28h Initialization before setting the video mode is complete.
B-5 Appendix B: BIOS POST Checkpoint Codes Checkpoint Code Description 4Ch The memory below 1 MB has been cleared via a soft reset. Clearing the memory above 1 MB next. 4Dh The memory above 1 MB has been cleared via a soft reset. Saving the memory size next.
B-6 H8DMR-82/H8DMR-i2 User ’s Manual Checkpoint Code Description 86h The password was checked. Performing any required programming before WIN- BIOS Setup next. 87h The programming before WINBIOS Setup has completed. Uncompressing the WINBIOS Setup code and executing the AMIBIOS Setup or WINBIOS Setup utility next.
B-7 Appendix B: BIOS POST Checkpoint Codes Checkpoint Code Description A9h Returned from adaptor ROM at E000h control. Performing any initialization required after the E000 option ROM had control next. Aah Initialization after E000 option ROM control has completed.
B-8 H8DMR-82/H8DMR-i2 User ’s Manual (continued from front) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities o.
Ein wichtiger Punkt beim Kauf des Geräts Supermicro MBD-H8DMR-82-B (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Supermicro MBD-H8DMR-82-B noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Supermicro MBD-H8DMR-82-B - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Supermicro MBD-H8DMR-82-B reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Supermicro MBD-H8DMR-82-B erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Supermicro MBD-H8DMR-82-B besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Supermicro MBD-H8DMR-82-B verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Supermicro MBD-H8DMR-82-B. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Supermicro MBD-H8DMR-82-B gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
