Benutzeranleitung / Produktwartung P4SCT des Produzenten SUPER MICRO Computer
Zur Seite of 100
® SUPER P4SCT SUPER P4SCT+ SUPER P4SCT+II USER’S MANUAL Revision 1.0c S UPER.
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.
Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the SUPER P4SCT/P4SCT+/P4SCT+II motherboard. The P4SCT/P4SCT+/ P4SCT+II supports single Intel Pentium ® 4 processors or Celeron proces- sors up to 3.
S UPER P4SCT/P4SCT+/P4SCT+II User’s Manual iv Table of Contents About This Manual ...................................................................................................... i i i Manual Organization ......................................
ATX PS/2 Keyboard/Mouse Ports ....................................................... 2-15 Universal Serial Bus (USB) .................................................................. 2-15 Wake-On-Ring ................................................
vi Table of Contents Chapter 4: BIOS 4 -1 Introduction ....................................................................................................... 4 - 1 4 -2 Running Setup ...................................................................
Chapter 1: Introduction 1-1 Chapter 1 Introduction 1 - 1 Overview Checklist Congratulations on purchasing your computer motherboard from an ac- knowledged leader in the industry. Supermicro boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance.
1-2 S UPER P4SCT/P4SCT+/P4SCT+II User’s Manual Contacting Supermicro Headquarters Address: SuperMicro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: + 1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.
Chapter 1: Introduction 1-3 Figure 1-1. SUPER P4SCT Image SUPER P4SCT (1. *Please see Notes on the next page for the differences between the P4SCT, the P4SCT+ and the P4SCT+II. 2. *All graphics and pictures shown in this manual were based upon the latest PCB revision available at the time of publishing of this manual.
1-4 S UPER P4SCT/P4SCT+/P4SCT+II User’s Manual Figure 1-4. SUPER P4SCT/P4SCT+/P4SCT+II Motherboard Layout CPU 478 PGA MCH PWR LED COM2 J17 J21 J20 USB 1/2 Parallel Port JP8 J11 JL1 JPWAKE WOR JP1 JP.
Chapter 1: Introduction 1-5 P4SCT/P4SCT+/P4SCT+II Quick Reference Jumpers Description Default Setting J18 Speaker Pins 3-4 (In.Buzzer) J33 VGA Enable/Disable Pins 1-2 (Enabled) J36 Keylock Header Open.
1-6 S UPER P4SCT/P4SCT+/P4SCT+II User’s Manual Figure 1-6. P4SCT/P4SCT+/P4SCT+II System Block Diagram: (with the 6300ESB Hance Rapids Chipset) Note: This is a general block diagram and may not exactly represent the features on your motherboard. See the follow- ing pages for the actual specifications of the motherboard.
Chapter 1: Introduction 1-7 Motherboard Features CPU Latest CPU technology! • Single Pentium ® 4 478-pin PGA processors or Intel Celeron processors up to up to 3.40 GHz (at a 800/533/400 MHz FSB) w/HyperThreading. • Intel Pentium 4/Celeron processors (*use 0.
1-8 S UPER P4SCT/P4SCT+/P4SCT+II User’s Manual ACPI Features • Microsoft OnNow • Slow blinking LED for suspend state indicator • BIOS support for USB keyboard • Main switch override mechanis.
Chapter 1: Introduction 1-9 1-2 Chipset Overview: Intel's Canterwood(875P) and Canterwood ES (E7210) Intel’s Canterwood Chipset (875P) and Canterwood ES (E7210) contains the following main components: Canterwood Memory Controller Hub (MCH) and the I/O Controller Hub (6300ESB-Hance Rapids ICH).
1-10 S UPER P4SCT/P4SCT+/P4SCT+II User’s Manual Marvell's 88SX5041 Host Controller (*For the P4SCT+/P4SCT+II only) The Marvell 88SX5080 device is a PCI/PCI-X to Serial ATA (SATA) host controller with expansion ROM interface.
Chapter 1: Introduction 1-11 1-3 PC Health Monitoring This section describes the PC health monitoring features of the SUPER P4SCT/P4SCT+/P4SCT+II. The motherboard has an onboard System Hard- ware Monitor chip that supports PC health monitoring. Eight Onboard Voltage Monitors for the CPU Core, +3.
1-12 S UPER P4SCT/P4SCT+/P4SCT+II User’s Manual 1-4 Power Configuration Settings This section describes features of your motherboard that deal with power and power settings. Microsoft OnNow The OnNow design initiative is a comprehensive, system-wide approach to system and device power control.
Chapter 1: Introduction 1-13 Wake-On-LAN is defined as the ability of a management application to remotely power up a computer that is powered off. Remote PC setup, updates and asset tracking can occur after hours and on weekends so that daily LAN traffic is kept to a minimum and users are not interrupted.
1-14 S UPER P4SCT/P4SCT+/P4SCT+II User’s Manual 1-6 Super I/O The disk drive adapter functions of the Super I/O chip include a floppy disk drive controller that is compatible with industry standard .
Chapter 2: Installation 2-1 Chapter 2 Installation 2- 1 Static-Sensitive Devices Electric Static Discharge (ESD) can damage electronic components. To prevent damage to your system board, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD.
2-2 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual IMPORTANT: Always connect the power cord last and always remove it before adding, removing or changing any hardware components. Make sure that you install the processor into the CPU socket before you install the CPU heatsink.
Chapter 2: Installation 2-3 5. Lift the lever on the CPU socket. Socket Lever 6. Install the CPU in the socket. Make sure that Pin 1 of the CPU is seated on Pin 1 of the socket (both corners are marked with a triangle). 7. Press the lever down until you hear it *click* into the locked position.
2-4 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 2-4 Installing DDR Memory CAUTION Exercise extreme care when installing or removing memory modules to prevent any possible damage. Memory Module Installation (See Figure 2-2) 1. Insert each DDR memory module vertically into its slot.
Chapter 2: Installation 2-5 T o Install: Insert module vertically and press down until it snaps into place. Pay attention to the notch. Figure 2-2. Side and Top Views of DDR Module Installation into Slot T o Remove: Use your thumbs gently to push each release tab outward to release the DIMM from the slot.
2-6 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Figure 2-4. Front Control Panel Connectors 2-5 I/O Port/Control Panel Connector Locations The I/O ports are color coded in conformance with the PC99 specification to make setting up your system easier.
Chapter 2: Installation 2-7 2-6 Connecting Cables Power Supply Connectors The primary power supply connector (J20) on the P4SCT/ P4SCT+/P4SCT+II meets the SSI (Superset ATX) 24-pin specifica- tion. Refer to the table on the right for the pin definitions of the ATX 20-pin power connector.
2-8 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Reset Connector The reset connector is located on pins 3 and 4 of JF1. This connec- tor attaches to the reset switch on the computer chassis.
Chapter 2: Installation 2-9 LAN1 LED Pow er Bu tto n Overh eat L ED 1 Res et B utton 2 ID E L E D Power On L ED Rese t Pw r Vc c Vc c Vc c Vc c Grou nd Grou nd 19 20 Vcc X Groun d NMI X X X LAN 2 LED GLAN1 LED The GLAN1 (Gigabit LAN) LED connection is located on pins 11 and 12 of JF1.
2-10 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual LAN1 LED Power Bu tton Overhe at LED 1 Re set Bu tton 2 IDE L ED Power On LED Res e t Pwr Vcc Vcc Vcc Vcc Ground Ground 19 20 Vcc X Ground NMI X X X LAN2 LED Power_LED Connector The Power LED connector is lo- cated on pins 15, 16 of JF1.
Chapter 2: Installation 2-11 LAN1 LED Pow er Bu tto n Overheat LED 1 Res et Bu tto n 2 ID E L ED Power On LE D Res et Pwr Vcc Vcc Vcc Vcc Ground Ground 19 20 Vc c X Ground NM I X X X LA N2 LE D Speaker Connector The speaker connector is located on J18.
2-12 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Fan Headers There are six fan headers on the P4SCT/P4SCT+/P4SCT+II, which are designated CPU/Chassis Fan1, CH Fan 2, CH Fan 3, CH Fan 4, and Over Heat Fan/CH Fan 5. (Chassis Fan 4 and Chassis Fan 5 are not monitored by BIOS.
Chapter 2: Installation 2-13 Chassis Intrusion The Chassis Intrusion header is designated JL1. See the board layout in Chapter 1 for the location of JL1 and the table on the right for pin definitions.
2-14 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Ethernet Ports GLAN1 and GLAN2 (*P4SCT/P4SCT+II only) Two Eth ernet ports (designated GLAN1 and GLAN2) are located beside the VGA port on the IO backplane. These ports accept RJ45 type cables. VGA Connector A VGA connector (JG1) is located next to the GLAN1 on the IO backplane.
Chapter 2: Installation 2-15 Universal Serial Bus (USB) There are two Universal Serial Bus Connectors (USB 1/2: J12/ J13) located on the I/O panel and additional two USB headers are located on the motherboard. These ports, labeled USB3/4, can be used to provide front side chassis access (cables not in- cluded).
2-16 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Pin Num ber 1 2 D efi nition Ground Wa ke - u p Wake- On- Ring Pin Defi ni tions (WOR) Keylock Enable/Disable The Keylock header is located on J36. Close Pin 1 and Pin 2 of J36 to enable the function of Keylock.
Chapter 2: Installation 2-17 Intel's SATA LED The header for Intel's SATA LED is located on J37. This header will display all Intel's SATA activities.
2-18 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual CMOS Clear JBT1 is not actually a jumper but consists of two contact pads. To clear the contents of CMOS, short these pads together by touching them both with a metal conductor such as the head of a small screwdriver.
Chapter 2: Installation 2-19 USB Wake-Up (*USB1/2 Only) Use JPUSB1 to enable or disable USB Wake-Up, which allows you to wakeup the system by de- pressing a key on the keyboard or by clicking the mouse when either is connected to the USB1 or USB2 port.
2-20 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Watch Dog Enable/Disable JP8 enables the Watch Dog func- tion. Watch Dog is a system moni- tor that can reboot the system when a software application is "hung up". Pins 1-2 will cause WD to reset the system if an applica- tion is "hung up".
Chapter 2: Installation 2-21 GLAN2 Enable/Disable (*P4SCT+/P4SCT+ only) Change the setting of jumper JPL2 to enable or disable the onboard LAN on the motherboard. See the table on the right for jumper set- tings. The default setting is En- abled. (For LAN1, please change the setting in the BIOS.
2-22 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Front Side Bus Speed JP1, JP2 are used to set the sys- tem (front side) bus speed for the processors. It is best to keep this jumper set to Auto. This jumper is used together with the CPU Clock setting in BIOS.
Chapter 2: Installation 2-23 2-8 Parallel Port, Floppy Drive, Hard Drive and AGP Connections Use the following information to connect the floppy and hard disk drive cables. • The floppy disk drive cable has seven twisted wires. • A red mark on a wire typically designates the location of pin 1.
2-24 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual IDE Connectors You do not need to configure the onboard IDE interfaces (- Pins 13,14 of JF1.) Refer to Figure 2-3 for location. See the table on the left for pin defini- tions. Note: You must use the ATA100/66 cable included with your system to benefit from the ATA100/66 technology.
Chapter 2: Installation 2-25 1.5V 8xAGP Pro Slot (*P4SCT/P4ST+II) The P4SCT/P4SCT+/P4SCT+II includes an 8xAGP Pro slot for high- performance video cards. It is backward compatible with 4xAGP and 2xAGP graphics cards. To install a VGA card, power down the system and remove the I/O shield corresponding to the AGP Pro slot.
2-26 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Notes.
3-1 Chapter 3: Troubleshooting Chapter 3 Troubleshooting 3-1 Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and s.
3-2 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual NOTE: If you are a system integrator, VAR or OEM, a POST diagnostics card is recommended. For I/O port 80h codes, refer to Appendix B. Memory Errors 1. Make sure the DIMM modules are properly and fully installed.
3-3 Chapter 3: Troubleshooting 2. BIOS upgrades can be downloaded from our web site at http://www.supermicro.com/techsupport/download.htm. Note: Not all BIOS can be flashed, it depends on the modifica- tions to the boot block code.
3-4 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Question: What's on the CD that came with my motherboard? Answer: The supplied compact disc has quite a few drivers and programs that will greatly enhance your system. We recommend that you review the CD and install the applications you need.
3-5 Chapter 3: Troubleshooting Question: How do I connect the ATA100/66 cable to my IDE device(s)? Answer: The 80-wire/40-pin high-density ATA100/66 IDE cable that came with your system has two connectors to support two drives. This special cable must be used to take advantage of the speed the ATA100/66 technol- ogy offers.
3-6 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Notes.
Chapter 4: BIOS 4-1 Chapter 4 BIOS 4-1 Introduction This chapter describes the AwardBIOS for the P4SCT/P4SCT+/P4SCT+II. The Award ROM BIOS is stored in a Flash chip and can be easily upgraded using a floppy disk-based program.
S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-2 4-2 Running Setup * Optimal default settings are in bold text unless otherwise noted . The BIOS setup options described in this section are selected by choosing the appropriate text from the Main BIOS Setup screen.
Chapter 4: BIOS 4-3 IDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave, IDE Channel 2 Master, IDE Channel 3 Master Press the <Auto> key to activate the function of 'IDE HDD Auto-Detecti.
S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-4 4-4.1 Advanced BIOS Features When the item of Advanced BIOS Features is highlighted, press the <Enter> key to activate the screen below: 4-4 Advanced BIOS Setup Choose Advanced BIOS Setup from the Award BIOS main menu with the Left/Right arrow keys.
Chapter 4: BIOS 4-5 ACPI Function Select "Enabled" to activate the function of BIOS Support for Advanced Configuration and Power Interface features. The settings are " Enabled " or "Disabled". ACPI Suspend Type If enabled, the option allows the user to determine the ACPI Suspend type.
S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-6 ECC Configuration This setting allows you to enable or disable ECC (Error Correction and Checking). The options are "ECC" and "Non-ECC". CSA LAN (Giga-LAN) Select "Enabled" to activate the function of CSA LAN.
Chapter 4: BIOS 4-7 USB Legacy Support This setting allows you to enable or disable the functions of USB, Keyboard/ Mouse under POST and DOS. The options are Disabled , and Enabled. CPU THRM-Throttling THRM throttling is used to lower power consumption and reduce the heat generated by the CPU.
S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-8 UART Mode Select This setting allows the user to select the UART mode for the BIOS. The options are "IrDA", "ASKIR" and " Normal ". RxD, TxD Active This allows the user to change the settings for the "RxD, TxD Active" function.
Chapter 4: BIOS 4-9 4-4.4 PnP Configuration Choose PCI/PnP Configurations from the Award BIOS main menu with the Left/Right arrow keys. You should see the following display: Enabling this setting resets the extended system configuration data when you exit setup.
S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-10 Resources Controlled By This setting allows BIOS to automatically configure all boot and Plug and Play compatible devices. If you choose Auto, you cannot select the IRQ, Onboard CSA LAN Boot Select "Enabled" to enable the Boot ROM embedded in the Onboard CSA LAN Chip.
Chapter 4: BIOS 4-11 4- 4. 6 Hardware Monitor Choose Hardware Monitor from the Award BIOS main menu with the Left/ Right arrow keys. You should see the following display: CPU Warning Temperature This allows you to set the CPU warning temperature.
S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-12 Hyper-Threading Technology Select "Enabled" to activate the hyper-threading function of the CPUs to make each CPU appear as if there were two CPUs to any programs that support it (you must have OS support also).
Chapter 4: BIOS 4-13 Set Supervisor Password When the item "Set Supervisor Password" is highlighted on the above screen, press the <Enter> key. When prompted, type the Supervisor Password in the dialogue box to set or to change the Supervisor Password.
S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-14 First Boot Device This item allows the user to set the first boot-up device. The options are "Removable", "Hard Disks", " CDROM ", "Legacy LAN", and "Disabled".
Chapter 4: BIOS 4-15 4-7 Exit Choose Exit from the Award BIOS main menu with the Left/Right arrow keys. You should see the following display: Save & Exit Setup When the item "Save & Exit Setup" is highlighted, press <Enter> to save the changes you've made in the BIOS program (CMOS) and exit.
S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-16 Load Fail-Safe Defaults Highlight this item and hit <Enter> to load the default settings for all items in the BIOS Setup. These are the safest settings to use. Load Optimized Defaults Highlight this item and hit <Enter> to load the optimized settings for all items in the BIOS Setup.
A-1 Appendix A: BIOS POST Messages Appendix A BIOS POST Messages During the Power-On Self-Test (POST), the BIOS will check for problems. If a problem is found, the BIOS will activate an alarm or display a message. The following is a list of such BIOS messages.
A-2 SUPER P4SCT/P4SCT+//P4SCT+II User's Manual Notes.
Appendix B: Award BIOS POST Codes B-1 Appendix B: Award BIOS POST Codes This section lists the POST (Power On Self Testing) Codes for the Award BIOS. POST ( hex) Descri ption CFh Test C MOS R/W functionality.
S UPER P4SCT/P4SCT+//P4SCT+II User’s Manual B-2 POST (hex) Description 0F h Rese r ve d 10h Au to detect flash type to lo ad ap propriate flash R/W codes into the ru n tim e area i n F000 f or E S CD & D M I s upport . 11h Res erv ed 12h Use walk ing 1’s algorithm to check out inter face in CMOS circuitry .
Appendix B: Award BIOS POST Codes B-3 2Dh 1. Initialize multi-language 2. Put information on screen display, inclu d ing Aw ard title, CPU type, CP U speed …. 2Eh Reser ved 2F h Rese r ve d 30h Re s erv ed 31h Res erv ed 32h Res erv ed 33h Re s et ke ybo ard exc ept W i nbon d 977 se ri es S upe r I/ O chi ps .
S UPER P4SCT/P4SCT+//P4SCT+II User’s Manual B-4 POST (hex) Description 58h Res erv ed 59 h Initialize the combined Tr end Anti-Virus code. 5Ah Re se r ve d 5B h (O pt iona l Fe atur e) Show mess ag e for entering AWDFLAS H. EXE from FDD (optional) 5C h Rese r ve d 5Dh 1.
Appendix B: Award BIOS POST Codes B-5 POST (hex) Description 80h Rese r ve d 81h Rese r ve d 82 h 1. Cal l ch ips et pow er ma nage men t ho ok. 2. Rec ov er th e tex t font us ed by EPA l og o (not for f ull sc re e n logo) 3. If pas sw ord is set , as k f or pass w ord.
S UPER P4SCT/P4SCT+//P4SCT+II User’s Manual B-6 NOTES.
Appendix C: Software Installation Instructions C-1 Appendix C Inst alling Sof tware Drivers and Windows Operating System After all the hardware has been installed, you must first configure the Adaptec Embedded Serial ATA RAID Driver before you install the Windows operating system.
C-2 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual ATA Operate Mode You can select from the following two modes: Combined Mode and En- hanced Mode. Combined Mode: In this mode, system BIOS assigns the traditional IRQ 14 and IRQ 15 for the use of HDD.
Appendix C: Software Installation Instructions C-3 Configuring BIOS settings for the SATA RAID Functions (Enhanced Mode) 1. Press the <Del> key during system bootup to enter the BIOS Setup Utility. (*Note: If it is the first time to power on the system, we recommend that you load the Optimized Default Settings.
C-4 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual The Adaptec Embedded Serial ATA with HostRAID Con- troller Driver Adaptec's Embedded Serial ATA RAID with HostRAID controller adds RAID functio.
Appendix C: Software Installation Instructions C-5 Managing Arrays Select this option to view array properties, and delete arrays. The following sections describe the operations Of "Managing Arrays".
C-6 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Viewing Array Properties To view the properties of an existing array: 1. At the BIOS prompt, press Ctrl+A . 2. From the ARC menu, select Array Configuration Utility (ACU) . 3. From the ACU menu, select Manage Arrays (as shown on the previous screen.
Appendix C: Software Installation Instructions C-7 Creating Arrays Before creating arrays, make sure the disks for the array are connected and installed in your system. Note that disks with no usable space, or disks that are un-initialized are shown in gray and cannot be used.
C-8 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Assigning Array Properties Once you've create a new array, you are ready to assign the properties to the array. *Caution: Once the array is created and its properties are assigned, you cannot change the array properties using the ACU.
Appendix C: Software Installation Instructions C-9 2. Under the item " Arrays Label ", type in an label and press Enter . ( *Note: The label shall not be more than 15 characters.) 3. For RAID 0, select the desired stripe size. (*Note: Available stripe sizes are 16, 32, and 64 KB-default.
C-10 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Notes: 1. Before adding a new drive to an array, back up any data contained on the new drive. Otherwise, all data will be lost. 2. If you stop the Build or Clear process on a RAID 1 from ACU, you can restart it by pressing Ctrl+R.
Appendix C: Software Installation Instructions C-11 Adding a Bootable Array To make an array bootable: 1. From the Main menu, select Manage Arrays. 2. From the List of Arrays, select the array you want to make bootable, and press Ctrl+B.
C-12 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Adding/Deleting Hotspares (*Note: In order to rebuild a RAID (RAID 0 or RAID 1), you would need to add a new HDD as a hotspare.) 1. Turn on your computer and press Ctrl+A as prompted to access the ARC Utility.
Appendix C: Software Installation Instructions C-13 Initializing Disk Drives If an installed disk does not appear in the disk selection list for creating a new array, or if it appears grayed out, you may have to initialize it before you can use it as part of an array.
C-14 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 4. Use the up and down arrow keys to highlight the disk you wish to initialize and press Insert (as shown in the screen below).
Appendix C: Software Installation Instructions C-15 5. Repeat Step 4 so that both drives to be initialized are selected (as shown in the screen below). 6. Press Enter . 7. Read the warning message as shown in the screen. 8. Make sure that you have selected the correct disk drives to initialize.
C-16 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Rebuilding Arrays *Note 1: Rebuilding applies to Fault Tolerant array (RAID 1) only. If an array Build process (or initialization) is interrupted or critical with one member missing, you must perform a Rebuild to optimized its function- ality.
Appendix C: Software Installation Instructions C-17 Using the Disk Utilities The Disk Utilities enable you to format or verify the media of your Serial ATA hard disks. To access the disk utilities: 1. Turn on your computer and press Ctrl+A when prompted to access the ARC utility (as shown in the screen below.
C-18 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual 3 Select the desired disk and press Enter (as shown in the screen below.) 2. From the ARC menu, select Disk Utilities as shown in the screen below.
Appendix C: Software Installation Instructions C-19 You can choose from the following options: 1. Format Disk —Simulates a low-level format of the hard drive by writing zeros to the entire disk. Serial ATA drives are low-level formatted at the factory and do not need to be low-level formatted again.
C-20 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual m. After Windows OS Installation is completed, the system will automati- cally reboot. C-2 Installing Intel's Hance Rapids Driver by Adaptec and the OS f. Insert Microsoft Windows OS Setup CD in the CD Driver, and the system will start to boot up from CD.
Appendix C: Software Installation Instructions C-21 Driver/Tool Installation Display Screen (*Note: Click the icons showing a hand writing on paper to view the readme files for each item. Click the computer icons to the right of these items to install each item (from top to the bottom) one at a time.
C-22 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Supero Doctor III The Supero Doctor III program is a Web base management tool that supports remote management capability. It includes Remote and Local Management tools. The local management is called SD III Client.
Appendix C: Software Installation Instructions C-23 Supero Doctor III Interface Display Screen-II (Remote Control) (*Note: SD III Software Revision 1.0 can be downloaded from our Web site at: ftp://ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's Guide at: http://www.
C-24 S UPER P4SCT/P4SCT+/P4SCT+II User's Manual Notes.
Ein wichtiger Punkt beim Kauf des Geräts SUPER MICRO Computer P4SCT (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie SUPER MICRO Computer P4SCT noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für SUPER MICRO Computer P4SCT - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von SUPER MICRO Computer P4SCT reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über SUPER MICRO Computer P4SCT erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon SUPER MICRO Computer P4SCT besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von SUPER MICRO Computer P4SCT verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit SUPER MICRO Computer P4SCT. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei SUPER MICRO Computer P4SCT gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
