Benutzeranleitung / Produktwartung 6113L-8 des Produzenten SUPER MICRO Computer
Zur Seite of 104
® S UPER S ERVER 61 13L-8 S UPER S ERVER 61 13L-i USER’S MANUAL 1.0 S UPER.
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.
Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SuperServer 6113L-8/ 6113L-i. Installation and maintainance should be performed by experienced technicians only.
S UPER S ERVER 6113L-8/6113L-i User's Manual iv Chapter 5: Advanced Serverboard Setup Chapter 5 provides detailed information on the i2DML-8G2/i2DML-iG2 serverboard, including the locations and functions of connectors, headers and jumpers.
v Preface Notes.
S UPER S ERVER 6113L-8/6113L-i User's Manual vi Table of Contents Preface About This Manual ....................................................................................................... i i i Manual Organization ........................
Chapter 4: System Safety 4 - 1 Electrical Safety Precautions ........................................................................... 4- 1 4 - 2 General Safety Precautions ............................................................................
S UPER S ERVER 6113L-8/6113L-i User's Manual viii S M B ......................................................................................................... 5-21 SMB Power Connector ...........................................................
Table of Contents ix Appendices: Appendix A: BIOS Error Beep Codes ...................................................................... A-1 Appendix B: BIOS POST Codes .............................................................................. B -1 Appendix C: Software Installation .
S UPER S ERVER 6113L-8/6113L-i User's Manual x Notes.
Chapter 1 Introduction 1 - 1 Overview The Supermicro SuperServer 6113L-8/6113L-i is a high-end dual processor, 1U rackmount server that features some of the most advanced technology currently available.
S UPER S ERVER 6113L-8/6113L-i User's Manual 1-2 1- 2 Serverboard Features At the heart of the SuperServer 6113L-8/6113L-i lies the i2DML-8G2/i2DML-iG2, a dual Intel Itanium2 processor serverboard designed to provide maximum perfor- mance. Below are the main features of the i2DML-8G2/i2DML-iG2.
1-3 Chapter 1: Introduction Processors The i2DML-8G2/i2DML-iG2 supports single or dual Intel Itanium2 processors of up to 1.50 GHz with a 6 MB L3 cache at a 400 MHz FSB. Please refer to the support section of our web site for a complete listing of supported processors (http://www.
S UPER S ERVER 6113L-8/6113L-i User's Manual 1-4 Figure 1-1. E8870 Chipset Block Diagram Other Features Other onboard features are included to promote system health.
1-5 Chapter 1: Introduction 1- 3 Server Chassis Features The SC813HS-500/SC813Hi-500 is one of Supermicro's third-generation 1U chas- sis and features four SCSI/IDE hard drive bays, a slim CD-ROM drive and a revolutionary cooling design that can keep today's most powerful processors running well below their temperature thresholds.
S UPER S ERVER 6113L-8/6113L-i User's Manual 1-6 Cooling System The SC813HS-500/SC813Hi-500 chassis' revolutionary cooling design has been optimized to provide sufficient cooling for dual Itanium2 configurations. The SC813HS-500/SC813Hi-500 includes two heavy duty 10-cm blower fans located in the middle of the chassis.
1-7 Chapter 1: Introduction 1- 4 Contacting Supermicro Headquarters Address: SuperMicro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: + 1 (408) 503-8000 Fax: + 1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.
S UPER S ERVER 6113L-8/6113L-i User's Manual 1-8 Notes.
Chapter 2: Server Installation 2-1 Chapter 2 Server Installation 2-1 Overview This chapter provides a quick setup checklist to get your SuperServer 6113L-8/ 6113L-i up and running. Following these steps in the order given should enable you to have the system operational within a minimum amount of time.
S UPER S ERVER 6113L-8/6113L-i User's Manual 2-2 Choosing a Setup Location - Leave enough clearance in front of the rack to enable you to open the front door completely (~25 inches). - Leave approximately 30 inches of clearance in the back of the rack to allow for sufficient airflow and ease in servicing.
2-3 Chapter 2: Server Installation 2- 4 Installing the Server into a Rack This section provides information on installing the SuperServer 6113L-8/6113L-i into a rack unit with the rack rails provided. If the 6113L-8/6113L-i has already been mounted into a rack, you can skip ahead to Sections 2-5 and 2-6.
S UPER S ERVER 6113L-8/6113L-i User's Manual 2-4 Figure 2-1. Installing the Rack Rails Installing the Server into the Rack You should now have rails attached to both the chassis and the rack unit. The next step is to install the server into the rack.
2-5 Chapter 2: Server Installation Figure 2-2. Installing the Server into a Rack (front bezel is optional).
S UPER S ERVER 6113L-8/6113L-i User's Manual 2-6 Figure 2-3. Installing the Server into a Telco Rack (front bezel is optional) Installing the Server into a Telco Rack If you are installing the SuperServer 6113L-86113L-8/6113L-i into a Telco type rack, follow the directions given on the previous pages for rack installation.
2-7 Chapter 2: Server Installation 2- 5 Checking the Serverboard Setup After you install the 6113L-8/6113L-i in the rack, you will need to open the unit to make sure the serverboard is properly installed and all the connections have been made.
S UPER S ERVER 6113L-8/6113L-i User's Manual 2-8 Figure 2-4. Accessing the Inside of the SuperServer 6113L-8/6113L-i 6 . Check all cable connections and airflow: Make sure all power and data cables are properly connected and not blocking the chassis airflow.
2-9 Chapter 2: Server Installation 2- 6 Checking the Drive Bay Setup Next, you should check to make sure the peripheral drives and the SCSI/IDE drives have been properly installed and all connections have been made. 1 . Accessing the drive bays: All drives are accessable from the front of the server.
S UPER S ERVER 6113L-8/6113L-i User's Manual 2-10 Notes.
Chapter 3: System Interface 3-1 Chapter 3 System Interface 3 - 1 Overview There are several LEDs on the chassis control panel to keep you constantly informed of the overall status of the system as well as the activity and health of specific components.
S UPER S ERVER 6113L-8/6113L-i User's Manual 3-2 3-3 Control Panel LEDs The control panel located on the front of th SC813HS-500/SC813Hi-500 chassis has four LEDs. These LEDs provide you with critical information related to different parts of the system.
3-3 Chapter 3: System Interface ! Power: Indicates power is being supplied to the system's power supply units. This LED should normally be illuminated when the system is operating. 3-4 SCSI Drive Carrier LEDs (6113L-8 only) Each SCSI drive carrier has two LEDs.
S UPER S ERVER 6113L-8/6113L-i User's Manual 3-4 Notes.
Chapter 4: System Safety 4-1 Chapter 4 System Safety 4- 1 Electrical Safety Precautions ! Basic electrical safety precautions should be followed to protect yourself from harm and the SuperServer 6113L.
S UPER S ERVER 6113L-8/6113L-i User's Manual 4-2 4- 2 General Safety Precautions Follow these rules to ensure general safety: ! Keep the area around the SuperServer 6113L-8/6113L-i clean and free of clutter. ! The SuperServer 6113L-8/6113L-i weighs approximately 42 lbs (19.
4-3 Chapter 4: System Safety 4- 3 ESD Precautions Electrostatic discharge (ESD) is generated by two objects with different electrical charges coming into contact with each other. An electrical discharge is created to neutralize this difference, which can damage electronic com- ponents and printed circuit boards.
S UPER S ERVER 6113L-8/6113L-i User's Manual 4-4 4- 4 Operating Precautions Care must be taken to assure that the chassis cover is in place when the 6113L- 8/6113L-i is operating to ensure proper cooling. Out of warranty damage to the 6113L-8/6113L-i system can occur if this practice is not strictly followed.
Chapter 5: Advanced Serverboard Setup Chapter 5 Advanced Serverboard Setup This chapter covers the steps required to install processors and heatsinks to the i2DML-8G2/i2DML-iG2 serverboard, connect the data and power cables and in- stall add-on cards.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-2 ! 5- 2 Itanium2 Processor and Heatsink Installation When handling the processor package, avoid placing direct pressure on the label area of the fan. Also, do not place the serverboard on a conductive surface, which can damage the BIOS battery and prevent the system from booting up.
Chapter 5: Advanced Serverboard Setup 5-3 1.) Place the retention mechanism on the serverboard. 2.) Screw in three 6-32 4.5-mm screws from the reverse side of the serverboard. Installing the Heatsink Retention Mechanism 1. Place the retention mechanism (SKT-0147-RM-IT2) on the serverboard as shown in the picture below: 2.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-4 Installing Itanium2 CPUs 1. Insert an Itanium2 CPU into the CPU1 socket. Make sure that CPU Pin 1 is aligned with the cut angle of the CPU socket, as shown in the picture below.* Itanium2 CPU CPU1 Socket 2.
Chapter 5: Advanced Serverboard Setup 5-5 The CPU power pod is a VRM mechanism specially designed for Itanium2 pro- cessors. 1. Locate the slot on the CPU power pod and align it with the Itanium2 CPU installed on the serverboard.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-6 4. Repeat steps 1 and 2 to install a second power pod as needed. Securing the power pod with four M3 screws. 3. Locate four of the M3 screws in the heatsink retention package and use them to secure the power pod onto the serverboard as shown in the picture below.
Chapter 5: Advanced Serverboard Setup 5-7 Warning: Do not apply any thermal grease to the heatsink; the required amount of thermal grease has already been applied. To maximizing the cooling effect of the i2DML-8G2/i2DML-iG2, we strongly rec- ommend that Supermicro's proprietary heatsinks (SNK-0046) be used with Itanium2 CPUs.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-8 3. Secure the heatsink onto the CPU by tightening all four screws. 4. Repeat the above steps to install a second heatsink on a second CPU if needed. Figure 5-3. CPUs (2) with Heatsinks Installed Connecting AC Power 1.
Chapter 5: Advanced Serverboard Setup 5-9 5- 3 Connecting Cables Now that the processors are installed, the next step is to connect the cables to the serverboard. These include the data (ribbon) cables for the peripherals and control panel and the power cables.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-10 Figure 5-4. Front Control Panel Header Pins (U66) Po we r B ut t on Overheat LE D 1 NI C1 LED R ese t B utton 2 P o w er F a il L E D NI C2 LED H.
Chapter 5: Advanced Serverboard Setup 5-11 5- 4 I/O Ports The I/O ports are color coded in conformance with the PC 99 specification. See Figure 5-5 below for the locations of the various I/O ports. Figure 5-5. I/O Port Locations 5- 5 Installing Memory Note: Check the Supermicro web site for recommended memory modules: http:// www.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-12 Figure 5-6b. Top View of DIMM Socket Figure 5-6a. Side View of DIMM Installation into Socket To Install: Insert module vertically and press down until it snaps into place. Pay attention to the bottom notch.
Chapter 5: Advanced Serverboard Setup 5-13 5- 6 Adding PCI Cards 1 . PCI-X slot: The i2DML-8G2/i2DML-iG2 has one 64-bit 133 MHz PCI-X slot. The server should have come with a riser card installed, which supports a standard sized PCI-X card (see Figure 5-7).
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-14 Figure 5-8. SUPER i2DML-8G2 Layout (not drawn to scale) 5- 7 Serverboard Details PW1 J16 J15 J13 J14 1 5 2 6 3 7 4 8 SPKR S4 BIOS4 IPMI CPU1 CPU2.
Chapter 5: Advanced Serverboard Setup 5-15 i2DML-8G2/i2DML-iG2 Quick Reference Jumper Description Default Setting C N 5 Power Fail Alarm Enable/Disable Closed (Disabled) J 7 GLAN Enable/Disable Pins 1.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-16 5- 8 Connector Definitions Pins 1 thru 2 3 thru 4 Definition Ground +12v 4-Pin, 12v Pow er Supp ly Connector s (to power pods) EPS 12V Power Connector There are two 24-pin main power sup- ply connectors on the serverboard.
Chapter 5: Advanced Serverboard Setup 5-17 NIC1 LED The NIC (Network Interface Control- ler) LED connection for the GLAN port is located on pins 11 and 12 of U66. Attach the NIC LED cable to display network activity. Refer to the table on the right for pin definitions.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-18 Power Button The Power Button connection is lo- cated on pins 1 and 2 of U66. Mo- mentarily contacting both pins will power on/off the system. This button can also be configured to function as a suspend button (see the appropri- ate setting in BIOS).
Chapter 5: Advanced Serverboard Setup 5-19 Front Panel Universal Serial Bus Header Two extra USB headers (USB2/3 lo- cated at J21) can be used to provide front side USB access. You will need a USB cable to use either con- nection. Refer to the table on the right for pin definitions.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-20 Power Fault Connect a cable from your power supply to the U62 header to provide warning of power supply failure. This warning signal is passed through the PWR_LED pin on U66 to indicate a power failure on the chassis.
Chapter 5: Advanced Serverboard Setup 5-21 SMB A System Management Bus header is located at J22. Connect the ap- propriate cable here to utilize SMB on your system.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-22 VGA Enable/Disable JV1 allows you to enable or disable the VGA port. The default position is on pins 1 and 2 to enable VGA.
Chapter 5: Advanced Serverboard Setup 5-23 GLAN Enable/Disable Change the setting of jumper J7 to enable or disable the onboard GLAN ports (GLAN1 and GLAN2) on the serverboard.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-24 LED Color Off Green Orange Definition No Connection 100 Mb 1 Gb Gb LA N R ight LED Indi cat or 5-10 Onboard Indicators GLAN LEDs Each of the Gigabit Ethernet LAN ports (located beside the COM2 port on the back panel) has two LEDs.
Chapter 5: Advanced Serverboard Setup 5-25 5-11 SCSI and IDE Disk Drive Connections When connecting the hard disk drive cables, please note that a red mark on a wire typically designates the location of pin 1. SCSI Activity LED (6113L-8 only) The SCSI Activity LED is located next to the LSI SCSI controller.
S UPER S ERVER 6113L-8/6113L-i User's Manual 5-26 Signal Names +DB(12) +DB(13) +DB(14) +DB(15) +DB(P1) +DB(0) +DB(1) +DB(2) +DB(3) +DB(4) +DB(5) +DB(6) +DB(7) +DB(P) GROUND DIFFS ENS TERMPWR TERM.
Chapter 6: Advanced Chassis Setup 6-1 Chapter 6 Advanced Chassis Setup This chapter covers the steps required to install components and perform maintenance on the SC813HS-500/SC813Hi-500 chassis. For component instal- lation, follow the steps in the order given to eliminate the most common problems encountered.
6-2 S UPER S ERVER 6113L-8/6113L-i User's Manual Figure 6-1. Chassis: Front and Rear Views 6-2 Control Panel The control panel (located on the front of the chassis) must be connected to the JF2 connector on the serverboard to provide you with system status indications.
Chapter 6: Advanced Chassis Setup 6-3 6-3 System Fans Two 10-cm blower fans and a high-speed 4-cm fan provide all the cooling needed for the SuperServer 6113L-8/6113L-i. It is very important that the chassis top cover is properly installed and making a good seal for the cooling air to circulate properly through the chassis and cool the components.
6-4 S UPER S ERVER 6113L-8/6113L-i User's Manual Figure 6-2. System Cooling Fans 6-4 Drive Bay Installation/Removal Removing the Front Bezel If your system has a front bezel (optional) attached to the chassis, you must first remove it to gain access to the drive bays.
Chapter 6: Advanced Chassis Setup 6-5 Accessing the Drive Bays SCSI/IDE Drives: Because of their hotswap capability, you do not need to access the inside of the chassis or power down the system to install or replace SCSI drives. Proceed to the next step for instructions.
6-6 S UPER S ERVER 6113L-8/6113L-i User's Manual SCSI/IDE Drive Installation 1 . Mounting a SCSI/IDE drive in a drive carrier: The SCSI/IDE drives are mounted in drive carriers to simplify their installation and removal from the chassis. These carriers also help promote proper airflow for the SCSI/IDE drive bays.
Chapter 6: Advanced Chassis Setup 6-7 2 . Installing/removing hot-swap SCSI drives (6113L-8 only): The SCSI drive bays are located in the front of the chassis, making them easily accessible for installation and removal. The SCSI drives are hot-swap units, meaning that they can be installed and removed while the system is running.
6-8 S UPER S ERVER 6113L-8/6113L-i User's Manual CD-ROM Drive Installation The top cover of the chassis must be opened to gain full access to the CD-ROM drive bay. The 6113L-8/6113L-i accomodates only slim CD-ROM drives. Side mounting brackets are needed to mount a slim CD-ROM drive in the 6113L-8/ 6113L-i server.
Chapter 6: Advanced Chassis Setup 6-9 6-5 Power Supply The SuperServer 6113L-8/6113L-i has a single 500 watt power supply, which is auto-switching capable. This enables it to automatically sense and operate with either a 100v or 240v input voltage. An amber light will be illuminated on the power supply when the power is off.
6-10 S UPER S ERVER 6113L-8/6113L-i User's Manual Figure 6-6. Removing/Replacing the Power Supply.
Chapter 7: BIOS 7-1 Chapter 7 BIOS 7-1 Introduction This chapter describes the AMIBIOS settings for the i2DML-8G2/i2DML-iG2. The AMI ROM BIOS is stored in a Flash EEPROM and can be easily upgraded using a floppy disk-based program.
7-2 S UPER S ERVER 6113L-8/6113L-i User's Manual When you select the Main Setup, the AMI BIOS Version, BIOS Build Date, BIOS ID and System Memory will all be displayed. Language Menu This option allows you to set the default Language used by the BIOS.
Chapter 7: BIOS 7-3 7- 3 Advanced Setup Screen Selecting the Advanced tab takes you to the Advanced setup screen. The Advanced BIOS Setup screen and sub menus are listed below: When you first enter the Advanced Setup screen, the Setup Warning will be displayed.
7-4 S UPER S ERVER 6113L-8/6113L-i User's Manual Serial Port1 Address/Serial Port2 Address This option specifies the base I/O port addresses and Interrupt Request addresses of Serial Port 1 and Serial Port2. Select "Disabled" to prevent the serial ports from accessing any system resources.
Chapter 7: BIOS 7-5 Primary IDE Master/Slave, Secondary IDE Master/Slave From the Advanced Setup screen, press <Enter> on the appropriate option to access primary and secondary IDE master and slave drives submenu. Use this screen to select options for the Primary and Secondary IDE drives.
7-6 S UPER S ERVER 6113L-8/6113L-i User's Manual DMA Mode Select the default setting of Auto to allow the BIOS to auto detect the DMA mode. Use this value if the IDE disk drive support cannot be determined. Other- wise, select from one of the following options: SWDMA0 (Single Word DMA mode 0, 2.
Chapter 7: BIOS 7-7 ATA(PI) 80-Pin Cable Detection This feature allows the BIOS to auto-detect the 80-pin ATA(PI) Cable. The options are "Host & Device" , "Host" and "Device." ! ! ! ! ! BIOS Settings Configuration This item allows the user to configure the system's boot settings.
7-8 S UPER S ERVER 6113L-8/6113L-i User's Manual ! System Health Monitor This feature allows the BIOS to automatically display the status of the following items: CPU Overheat Temperature, CPU1/CPU2 Temperature, various voltage levels and fan speeds.
Chapter 7: BIOS 7-9 ! Peripheral Device Configuration This screen allows the user to configure the Peripheral Device settings Power Loss Control This setting allows you to choose how the system will react when power is returned to the system after being unexpectedly lost.
7-10 S UPER S ERVER 6113L-8/6113L-i User's Manual ! USB Configuration This feature allows the user to configure the USB settings. USB Function Select "Enabled" to enable the USB Host Controller. The options are "Disabled" and " Enabled .
Chapter 7: BIOS 7-11 7-4 PCI/PnP Configuration This feature allows the user to set the PCI/PnP configuration. PCI Latency Timer This option sets the latency time for all PCI devices on the PCI bus.
7-12 S UPER S ERVER 6113L-8/6113L-i User's Manual Change Supervisor Password Select this option and press <Enter> to access the submenu, then type in the password. 7- 5 Security Settings BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor password must be set first.
Chapter 7: BIOS 7-13 7- 6 Exit Options Select the Exit tab from the BIOS Setup Utility screen to enter the Exit BIOS Setup screen. Exit Saving Changes When you have completed the system configuration .
7-14 S UPER S ERVER 6113L-8/6113L-i User's Manual Load Optimal Defaults Select Load Optimal Defaults from the Exit menu and press <Enter> then "OK" to have BIOS automatically load all Optimal Defaults for the BIOS settings.
Appendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur. Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process.
A-2 S UPER S ERVER 6113L-8/6113L-i User's Manual A- 2 IA-64 Common Debug Codes DS4 DS3 On On: SNC found and start memory sizing On Off: Initial system memory and SIOH Off On: Valid memory and SIO.
B-1 Appendix B: BIOS POST Codes Appendix B BIOS POST Codes When AMIBIOS performs the Power On Self Test, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, diagnostic equipment can be attached to the computer to read I/O port 0080h.
B-2 S UPER S ERVER 6113L-8/6113L-i User's Manual Checkpoint Code Description 03h The NMI is disabled. Next, checking for a soft reset or a power on condition. 05h The BIOS stack has been built. Next, disabling cache memory. 06h Uncompressing the POST code next.
B-3 Appendix B: BIOS POST Codes Checkpoint Code Description 24h The configuration required before interrupt vector initialization has completed. Interrupt vector initialization is about to begin. 25h Interrupt vector initialization is done. Clearing the password if the POST DIAG switch is on.
B-4 S UPER S ERVER 6113L-8/6113L-i User's Manual Checkpoint Code Description 4 7h The memory pattern has been written to extended memory. Writing patterns to the base 640 KB memory next. 4 8h Patterns written in base memory. Determining the amount of memory below 1 MB next.
B-5 Appendix B: BIOS POST Codes Checkpoint Code Description 60h The DMA page register test passed. Performing the DMA Controller 1 base register test next. 62h The DMA controller 1 base register test passed. Performing the DMA controller 2 base register test next.
B-6 S UPER S ERVER 6113L-8/6113L-i User's Manual Checkpoint Code Description 95h Initializing the bus option ROMs from C800 next. See the last page of this chapter for additional information. 96h Initializing before passing control to the adaptor ROM at C800.
Appendix C: Software Installation C-1 Appendix C Software Installation After all the hardware has been installed, you will need to install the operating system and other software drivers. The necessary drivers are all included on the Supermicro CDs that came packaged with your system.
C-2 S UPER 6113L-8/6113L-i User's Manual C-2 AMIBIOS Flash 1. Obtain a USB Pen or a USB storage device (a USB 2.0 device is recommended). 2. From our web site (www.supermicro.com), download the following two files into the USB pen or device: [amiflash.
Appendix C: Software Installation C-3 Locate of the USB device (example) Location of the USB device (example) 6. At the shell command prompt, type: Shell> fsX: (where X is the number of the sector in which your USB pen or device is located). This command will change the directory from [Shell] to [fsX].
C-4 S UPER 6113L-8/6113L-i User's Manual 9. When the fsx directory appears, type in the file name at the prompt: fsx: amiflash ami64.rom (eg. in the example shown above, at the prompt type fs0:> amiflash ami64.rom and press <Enter> as shown below).
Appendix C: Software Installation C-5 After the BIOS Image file is loaded, the following screen will appear: 10. When "Reset NVRAM to default value? (y/n)" is displayed, type "y" at the prompt if you want to reset all default values after flashing the BIOS.
C-6 S UPER 6113L-8/6113L-i User's Manual C-3 Adding the CD-ROM Boot Option in EFI 1. Power on the system and enter the “EFI Boot Manager”. 2. Select “Boot Option Maintenance Menu." 3. Select “Add a Boot Option.” 4. Select “Removable Media Boot [Acpi(PNP0A03,0)/Pci(1F|1)/ ATA(Secondary,Master)]”.
Appendix C: Software Installation C-7 C-4 IA64 OS Installation For installation on an IDE hard drive. (Note: The Itanium2 board does not have a floppy connector, so the user cannot install Windows driver through a floppy device.
C-8 S UPER 6113L-8/6113L-i User's Manual 11. At the Shell command prompt, type: "Shell> exit". This command will exit the EFI Shell and return to the EFI Boot Manager.” 12. Select the “CD-ROM” boot option to boot from a Windows OS installation CD after you have added the CD-ROM boot option in the EFI Boot Manager.
D-1 Appendix D: System Specifications Appendix D System Specifications Processors Single or dual Intel ® Itanium ® 2 processors of up to 1.50 GHz with a 6 MB L3 cache at a front side (system) bus speed of 400 MHz Note: Please refer to the support section of our web site for a complete listing of supported processors.
S UPER S ERVER 6113L-8/6113L-i User's Manual D-2 Weight Gross Weight: 42 lbs. (19.1 kg.) System Cooling Two (2) 10-cm blower fans and one (1) high-speed 4-cm fan System Input Requirements AC Inpu.
Ein wichtiger Punkt beim Kauf des Geräts SUPER MICRO Computer 6113L-8 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie SUPER MICRO Computer 6113L-8 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für SUPER MICRO Computer 6113L-8 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von SUPER MICRO Computer 6113L-8 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über SUPER MICRO Computer 6113L-8 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon SUPER MICRO Computer 6113L-8 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von SUPER MICRO Computer 6113L-8 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit SUPER MICRO Computer 6113L-8. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei SUPER MICRO Computer 6113L-8 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
