Benutzeranleitung / Produktwartung 6015TC-10G des Produzenten SUPER MICRO Computer
Zur Seite of 102
S UPER S UPER S ER VER 6015TC-T S UPER S ER VER 6015TC-10G USER’S MANUAL Revision 1.0a ®.
Manual Revision 1.0a Release Date: November 1 1, 2008 Unless you request and receive written permission from Super Micro Computer , Inc., you may not copy any part of this document.
Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SuperServer 6015TC- T/6015TC-10G. Installation and maintenance should be performed by experienced technicians only .
S UPER S ERVER 6015TC-T/6015TC-10G User's Manual iv Chapter 4: System Safety Y ou should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the SuperServer 6015TC-T/6015TC-10G.
v Preface Notes.
vi S UPER S ERVER 6015TC-T/6015TC-10G User's Manual T able of Contents Chapter 1 Introduction 1-1 Overview ......................................................................................................... 1-1 1-2 Serverboard Features ....
vii T able of Contents Installing the Inner Rails ................................................................................. 2-4 Installing the Outer Rails ................................................................................. 2-5 Locking T abs .
viii S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 5-6 Installing Memory ............................................................................................ 5-8 5-7 Adding PCI Cards ....................................................
Chapter 1 Introduction 1-1 Overview The SuperServer 6015TC-T/6015TC-10G is a "1U T win" server comprised of the SC808T -780 1U chassis and two (twin) X7DCT/X7DCT -10G serverboards. Please refer to our web site for information on operating systems that have been certi fi ed for use with the 6015TC-T/6015TC-10G (www .
1-2 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 1-2 Serverboard Features At the heart of the SuperServer 6015TC-T/6015TC-10G lies two X7DCT/X7DCT - 10G dual processor serverboards, which are based on Intel's 5100 chipset. Below are the main features of the X7DCT/X7DCT -10G.
Chapter 1: Introduction 1-3 Onboard Controllers/Ports Onboard I/O backpanel ports on each serverboard include one COM port, a VGA port, two USB ports and two Gigabit LAN (NIC) ports. The 6015TC-10G (only) also has an Intel® 82598EB 10 Gb Ethernet controller with a CX4 interface.
1-4 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Figure 1-1. Intel 5100 Chipset: System Block Diagram Note: This is a general block diagram. Please see Chapter 5 for details.
Chapter 1: Introduction 1-5 1-3 Server Chassis Features The following is a general outline of the main features of the SC808T -780 1U chas- sis. Details on the chassis can be found in Chapter 6.
1-6 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 1-4 1U T win: System Notes As a 1U T win con fi guration, the 6015TC-T/6015TC-10G is a unique server system. With two system boards incorporated into a single chassis, there are several points you should keep in mind.
Chapter 1: Introduction 1-7 1-5 Contacting Supermicro Headquarters Address: Super Micro Computer , Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.
1-8 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Notes.
Chapter 2: Server Installation 2-1 Chapter 2 Server Installation 2-1 Overview This chapter provides a quick setup checklist to get your 6015TC-T/6015TC-10G up and running. Following these steps in the order given should enable you to have the system operational within a minimum amount of time.
2-2 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Leave approximately 30 inches of clearance in the back of the rack to allow for • suf fi cient air fl ow and ease in servicing. This product is for installation only in a Restricted Access Location (dedicated • equipment rooms, service closets and the like).
Chapter 2: Server Installation 2-3 Always keep the rack's front door and all panels and components on the servers • closed when not servicing to maintain proper cooling. Make sure all power and data cables are properly connected and not blocking • the chassis air fl ow .
2-4 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 2-4 Installing the System into a Rack This section provides information on installing the 6015TC-T/6015TC-10G into a rack unit with the rack rails provided. If the system has already been mounted into a rack, you can skip ahead to Sections 2-5 and 2-6.
Chapter 2: Server Installation 2-5 Installing the Outer Rails Begin by measuring the distance from the front rail to the rear rail of the rack. Attach a short bracket to the front side of the right outer rail and a long bracket to the rear side of the right outer rail.
2-6 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Installing the Server into the Rack Y ou should now have rails attached to both the chassis and the rack unit. The next step is to install the server into the rack. Do this by lining up the rear of the chassis rails with the front of the rack rails.
Chapter 2: Server Installation 2-7 Figure 2-3. Installing the Server into a Rack Checking the Components and Setup Y ou may have one or two processors already installed in each of the two 1. serverboards. Each processor needs its own heatsink. See Chapter 5 for instructions on processor and heatsink installation.
2-8 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 2-6 Preparing to Power On Next, you should check to make sure the peripheral drives and the SA T A drives and SA T A backplane have been properly installed and all connections have been made.
Chapter 2: Server Installation 2-9 Figure 2-4. Accessing the Inside of the System.
2-10 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Notes.
Chapter 3: System Interface 3-1 Chapter 3 System Interface 3-1 Overview There are several LEDs on the two control panels as well as others on the SA T A drive carriers to keep you constantly informed of the overall status of the system as well as the activity and health of speci fi c components.
3-2 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 2 1 3-3 Control Panel LEDs Each of the two control panels located on the front of the SC808T -780 chassis has fi ve LEDs. Each LED provides you with critical information related its own speci fi c serverboard.
Chapter 3: System Interface 3-3 Power Indicates power is being supplied to the system's power supply unit. This LED should normally be illuminated when the system is operating. 3-4 SA T A Drive Carrier LEDs Each SA T A drive carrier has two LEDs.
3-4 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Notes.
Chapter 4: System Safety 4-1 Chapter 4 System Safety 4-1 Electrical Safety Precautions ! Basic electrical safety precautions should be followed to protect yourself from harm and the SuperServer 6015TC.
S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 4-2 4-2 General Safety Precautions Follow these rules to ensure general safety: Keep the area around the 6015TC-T/6015TC-10G clean and free of clutter . • The 6015TC-T/6015TC-10G weighs approximately 40 lbs (~18.
Chapter 4: System Safety 4-3 4-3 ESD Precautions Electrostatic discharge (ESD) is generated by two objects with different electrical charges coming into contact with each other . An electrical discharge is created to neutralize this difference, which can damage electronic com ponents and printed circuit boards.
S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 4-4 4-4 Operating Precautions Care must be taken to assure that the chassis cover is in place when the 6015TC- T/6015TC-10G is operating to assure proper cooling. Out of warranty damage to the system can occur if this practice is not strictly followed.
Chapter 5: Advanced Serverboard Setup 5-1 Chapter 5 Advanced Serverboard Setup This chapter covers the steps required to install the X7DCT/X7DCT -10G serverboard into the SC808T -780 chassis, connect the data and power cables and install add-on cards.
5-2 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 5-2 Serverboard Installation This section explains the fi rst step of physically mounting the X7DCT/X7DCT -10G into the SC808T -780 chassis. Following the steps in the order given will eliminate the most common problems encountered in such an installation.
Chapter 5: Advanced Serverboard Setup 5-3 5-3 Connecting Cables Now that the serverboards are installed, the next step is to connect the cables to the boards.
5-4 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 5-4 I/O Ports The I/O ports are color coded in conformance with the PC 99 speci fi cation. See Figure 5-2 below for the colors and locations of the various I/O ports. Figure 5-1. Control Panel Header Pins Note: The 10 Gb Ethernet port is included on the X7DCT -10G (6015TC-10G) only .
Chapter 5: Advanced Serverboard Setup 5-5 5-5 Processor and Heatsink Installation IMPORT ANT! A lways c o nne c t th e powe r c or d last a nd r emove i t fi rst bef ore add- ing , rem oving o r c hang ing a ny hard ware c ompo nent s.
5-6 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Socket key CPU installed in socket PnP cap released from load plate 3. Use your thumb and your index fi nger to hold the CPU at opposite sides. 4. Align pin1 of the CPU (the corner marked with a triangle) with the notched corner of the CPU socket.
Chapter 5: Advanced Serverboard Setup 5-7 War n in g! We do not recommend that the CPU or the heatsink be removed. However , if you do need to uninstall the heatsink, please follow the instructions below to prevent damage to the CPU or the CPU socket.
5-8 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 5-6 Installing Memory Memory Support The X7DCT/X7DCT -10G has six 240-pin DIMM slots that can support up to 48 GB of registered ECC DDR2-667/533 SDRAM (for a total of 96 GB in the system).
Chapter 5: Advanced Serverboard Setup 5-9 5-7 Adding PCI Cards PCI-Express Slot The 6015TC-T/6015TC-10G includes two preinstalled riser cards designed speci fi - cally for use in the SC808T -780 1U rackmount chassis. These riser cards support two low-pro fi le PCI-Express x16 cards to fi t inside the chassis.
5-10 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Figure 5-4. X7DCT -10G Layout 5-8 Serverboard Details FA N 3 FA N 1 FA N 2 JWD1 JPL1 JPG1 JPL2 JP A1 X7DCT LED2 JBT1 TLAN I2CPWR USB2/3 PCI-Exp.
Chapter 5: Advanced Serverboard Setup 5-1 1 Jumpers not indicated are for test purposes only . The 10 Gb LAN port is included on the X7DCT -10G only . X7DCT / X7DCT -1 0G Quick Reference Jumper Descri.
5-12 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Reset Connector The reset connector is located on pins 3 and 4 of JF1 and attaches to the reset switch on the computer chas- sis. See the table on the right for pin de fi nitions. PW_ON Connector The PW_ON connector is on pins 1 and 2 of JF1.
Chapter 5: Advanced Serverboard Setup 5-13 Overheat LED (OH) Connect an LED to the OH connection on pins 7 and 8 of JF1 to provide ad- vanced warning of chassis overheat- ing. Refer to the table on the right for pin de fi nitions. NIC2 (LAN2) LED The LED connections for LAN2 are on pins 9 and 10 of JF1.
5-14 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Universal Serial Bus (USB) There are two Universal Serial Bus ports located on the I/O panel, two USB headers located on the serverboard and a third USB port (USB4) located onboard near the SGPIO header .
Chapter 5: Advanced Serverboard Setup 5-15 LAN1/2 (Ethernet Ports) T wo gigabit Ethernet ports (designated LAN1 and LAN2) are located beside the VGA port on the I/O backplane. These ports accept RJ45 type cables. Serial Ports One serial port is included on the serverboard.
5-16 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 5-10 Jumper Settings T o modify the operation of the serverboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector .
Chapter 5: Advanced Serverboard Setup 5-17 W atch Dog Enable/Disable JWD enables the W atch Dog func- tion, a system monitor that takes action when a software application freezes the system. Jumping pins 1-2 will have WD reboot the system if a program freezes.
5-18 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 5-1 1 Onboard Indicators LAN1/LAN2 LEDs The Ethernet ports (located beside the VGA port) have two LEDs. On each Gb LAN port, one LED indicates activity when blinking while the other LED may be green, amber or off to indicate the speed of the connection.
Chapter 5: Advanced Serverboard Setup 5-19 Driver/T ool Installation Display Screen Note : Click the icons showing a hand writing on the paper to view the readme fi les for each item. Click a computer icon to the right of an item to install an item (from top to the bottom) one at a time.
5-20 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Supero Doctor III Interface Display Screen-I (Health Information) 5-13 Con fi guring Supero Doctor III The Supero Doctor III program is a Web-base management tool that supports remote management capability .
Chapter 5: Advanced Serverboard Setup 5-21 Note: SD III Software Revision 1.0 can be downloaded from our Web site at: ftp:// ftp.supermicro.com/utility/Supero_Doctor_III/. Y ou can also download SDIII User's Guide at: http://www .supermicro.com/PRODUCT/Manuals/SDIII/UserGuide.
5-22 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Notes.
Chapter 6: Advanced Chassis Setup 6-1 Chapter 6 Advanced Chassis Setup This chapter covers the steps required to install components and perform mainte- nance on the SC808T -780 chassis. For component installation, follow the steps in the order given to eliminate the most common problems encountered.
6-2 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Figure 6-2. Chassis Rear View 6-2 Control Panel Each control panel on the front of the chassis must be connected to the JF1 con- nector on its assiciated serverboard to provide you with system control buttons and status indicators.
Chapter 6: Advanced Chassis Setup 6-3 Use caution when working around the SA T A backplane. Do not touch the backplane with any metal objects and make sure no cables touch the backplane. Also, regardless of how many SA T A drives are installed, all four drive carriers must remain in the chassis to maintain proper air fl ow .
6-4 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Figure 6-3. Mounting a Drive in a Carrier Figure 6-4. Removing a SA T A Drive Installing/Removing Hot-swap SA T A Drives T o remove a carrier , push the release button located beside the drive LEDs.
Chapter 6: Advanced Chassis Setup 6-5 6-5 Power Supply The SuperServer 6015TC-T/6015TC-10G has a single 780 watt power supply . This power supply has the capability of operating at 100 - 240 input volts.
6-6 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Figure 6-4. Removing the Power Supply Before reconnecting the power cord, make sure the power switch on the 3. power supply is in the off position. Reconnect the power cord, replace the chassis top cover and push the unit 4.
Chapter 7: BIOS 7-1 Chapter 7 BIOS 7-1 Introduction This chapter describes the Phoenix BIOS™ Setup utility for the X7DCT/X7DCT -10G. The Phoenix ROM BIOS is stored in a fl ash chip and can be easily upgraded using a fl oppy disk-based program.
7-2 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual 7-2 Running Setup Default settings are in bold text unless otherwise noted . The BIOS setup options described in this section are selected by choosing the ap- propriate text from the main BIOS Setup screen.
Chapter 7: BIOS 7-3 Main BIOS Setup Menu Main Setup Features System Time T o set the system date and time, key in the correct information in the appropriate fi elds. Then press the <Enter> key to save the data. System Date Using the arrow keys, highlight the month, day and year fi elds, and enter the correct data.
7-4 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual X SA T A Port1, SA T A Port2, SA T A Port3 and SA T A Port4 These settings allow the user to set the parameters of SA T A Port, SA T A Port, SA T A Port3 and SA T A Port4. Hit <Enter> to activate the following sub-menu screen for detailed options of these items.
Chapter 7: BIOS 7-5 Multi-Sector T ransfers This item allows the user to specify the number of sectors per block to be used in multi-sector transfer . The options are Disabled , 4 Sectors, 8 Sectors and 16 Sectors. LBA Mode Control This item determines whether the Phoenix BIOS will access the IDE Channel 0 Master Device via the LBA mode.
7-6 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Disabled , the item-SA T A AHCI Enable will be available.) The options are Enabled and Disabled . ICH RAID Code Base Select to enable which SA T A RAID fi rmware to con fi gure. The options are Intel and Adaptec.
Chapter 7: BIOS 7-7 QuietBoot Mode This setting allows you to Enable or Disable the graphic logo screen during boot- up. POST Errors Set to Enabled to display POST Error Messages if an error occurs during bootup. If set to Disabled, the system will continue to boot without displaying any error message even when a boot error occurs.
7-8 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Power Button Behavior If set to Instant-Off, the system will power of f immediately as soon as the user hits the power button. If set to 4-sec., the system will power off when the user presses the power button for 4 seconds or longer .
Chapter 7: BIOS 7-9 Cache Base 0-512K If enabled, this feature will allow the data stored in the base memory block 0-512K to be cached (written) into a buffer , a storage area in the Static DROM (SDROM) or to be written into the L1/L2 cache inside the CPU to speed up CPU operations.
7-10 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual X PCI Con fi guration Access the submenu to make changes to the following settings for PCI devices. Onboard GLAN-1/Onboard GLAN-2 OPROM Con fi gure Select Enabled to allow the system to boot from the GLAN1 connection,the GLAN2 connection or the 10 Gb LAN port.
Chapter 7: BIOS 7-1 1 X Advanced Chipset Control Access the submenu to make changes to the following settings. W arning : T ake Caution when changing the Advanced settings. An incorrect setup, a very high DRAM frequency or an incorrect DRAM timing may cause the system become unstable.
7-12 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Patrol Scrubbing Scrubbing is a process that allows the North Bridge to correct correctable memoryer- rors detected on a memory module, and send the correction to the requestor (the original source).
Chapter 7: BIOS 7-13 Machine Checking (A vailable when supported by the CPU) Set to Enabled to activate the function of Machine Checking and allow the CPU to detect and report hardware (machine) errors via a set of model-speci fi c registers (MSRs). The options are Disabled and Enabled .
7-14 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Intel EIST Support (A vailable if supported by the CPU) Select Enabled to use the Enhanced Intel SpeedStep T echnology and allows the system to automatically adjust processor voltage and core frequency in an effort to reduce power consumption and heat dissipation.
Chapter 7: BIOS 7-15 Mode This setting allows you to set the type of device that will be connected to serial port B. The options are Normal and IR (for an infrared device). Base I/O Address This setting allows you to select the base I/O address for serial port B.
7-16 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual X Console Redirection Access the submenu to make changes to the following settings. COM Port Address This item allows you to specify which COM port to direct the remote console to: Onboard COM A or Onboard COM B.
Chapter 7: BIOS 7-17 X Hardware Monitor Logic Highlight this and hit <Enter> to see monitor data for the following items: CPU1 T emperature/CPU1 Secondary Core T emperature/CPU2 T emperature/CPU.
7-18 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual X IPMI (The option is available only when an IPMI card is installed in the system.) IPMI Speci fi cation V ersion This item displays the current IPMI V ersion. Firmware V ersion This item displays the current Firmware V ersion.
Chapter 7: BIOS 7-19 BIOS POST Errors Enabling this function to log POST errors. The options are Enabled and Dis- abled . BIOS POST W atch Dog Set to Enabled to enable POST W atch Dog. The options are Enabled and Dis- abled . OS Boot W atch Dog Set to Enabled to enable OS Boot W atch Dog.
7-20 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual X Realtime Sensor Data This feature display information from motherboard sensors, such as temperatures, fan speeds and voltages of various components. 7-5 Security Choose Security from the Phoenix BIOS Setup Utility main menu with the arrow keys.
Chapter 7: BIOS 7-21 Supervisor Password Is: This indicates if a supervisor password has been entered for the system. Clear means such a password has not been used and Set means a supervisor password has been entered for the system. User Password Is: This indicates if a user password has been entered for the system.
7-22 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Password on Boot This setting allows you to determine if a password is required for a user to enter the system at bootup. The options are Enabled (password required) and Disabled (password not required).
Chapter 7: BIOS 7-23 7-7 Exit Choose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys. Y ou should see the following display . All Exit BIOS settings are described in this section. Exit Saving Changes Highlight this item and hit <Enter> to save any changes you made and to exit the BIOS Setup utility .
7-24 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Save Changes Highlight this item and hit <Enter> to save any changes you made. Y ou will remain in the Setup utility .
A-1 Appendix A: BIOS POST Messages Appendix A BIOS POST Messages Du ri ng th e Power- O n Se lf- T e st (P OST ), th e BIO S wi ll c hec k fo r pr obl ems . If a pr obl em is f oun d, the B IO S wil l act ivate an a lar m or d isp lay a me ssa ge. T he fo l- l o wi n g i s a l i s t o f s u ch B I O S m e s s a g e s .
A-2 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual System CMOS checksum bad - Default con fi guration used System CMOS has been co rrupted or modi fi ed incorrect ly , perhaps by an applica - ti on pr og ram t hat c han ges d at a stor ed in C M OS.
A-3 Appendix A: BIOS POST Messages sl ows sys tem p er fo rm anc e c o nsi der ab ly . CPU I D: CPU s oc ket numb er fo r Mu lti - Pro c ess or e rr or .
A-4 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual I /O d evic e I RQ co n fl ict I/ O devic e I RQ c on fl ict er ror . PS/ 2 M ou se Bo ot S um ma r y Sc re e n: PS/ 2 M ous e inst all ed. nnnn kB Ex tended R AM Passed Wher e nnnn is the a mou nt of R A M i n kil oby tes su cc e ssf ull y teste d.
A-5 Appendix A: BIOS POST Messages Pre ss < F2 > t o ent e r Se tu p Op tio nal m es sa ge di spl ayed dur in g PO ST . Can b e tur ne d of f i n Setu p.
A-6 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Notes.
Appendix B: BIOS POST Codes B-1 Appendix B BIOS POST Codes This section lists the POST (Power On Self T est) codes for the PhoenixBIOS. POST codes are divided into two categories: recoverable and terminal. Recoverable POST Errors When a recoverable type of error occurs, BIOS will display an POST code that describes the problem.
B-2 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual POST Co d e De scr ip ti on 1 7h I nit iali ze ca ch e befo re me mo r y Aut o size 1 8 h 825 4 t ime r ini tia liz ati on 1 A h 8237 D M A c .
Appendix B: BIOS POST Codes B-3 POST Co d e De scr ip ti on 5C h T es t R A M b et wee n 5 12 and 6 4 0 kB 6 0h T e st ex tende d mem or y 62h T e st ex tend ed me mor y ad dre ss li nes 6 4h J ump to.
B-4 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual POST Co d e De scr ip ti on 9 9h C hec k fo r SM A RT D ri ve ( opt io nal) 9 Ch Set up Powe r Ma nag eme nt 9 Dh Init ial ize se cur it y e n.
Appendix B: BIOS POST Codes B-5 Th e fol low ing a re f or t he b oo t bl oc k in Fla sh RO M POST Co d e De scr ip ti on E0 h I nit iali ze the c hi pset E 1 h I nit ial ize th e br idg e E2 h I nit .
B-6 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Notes.
C-1 Appendix C: System Speci fi cations Appendix C System Speci fi cations Note: unless noted speci fi cations apply to a complete system (both server- boards). Processors Four Intel® Xeon® 5400/5300/5200/5100 Series processors in LGA771 sockets Note: please refer to our website for details on supported processors.
C-2 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual Weight Gross Weight: 40 lbs. (18.2 kg.) System Cooling Six (6) high-performance 4-cm PWM (Pulse Width Modulated) fans System Input Requirements AC Input V oltage: 100 - 240V AC auto-range Rated Input Current: 9.
C-3 Appendix C: System Speci fi cations Notes.
C-4 S UPER S ERVER 6015TC-T/6015TC-10G User's Manual (continued from front) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, n.
Ein wichtiger Punkt beim Kauf des Geräts SUPER MICRO Computer 6015TC-10G (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie SUPER MICRO Computer 6015TC-10G noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für SUPER MICRO Computer 6015TC-10G - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von SUPER MICRO Computer 6015TC-10G reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über SUPER MICRO Computer 6015TC-10G erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon SUPER MICRO Computer 6015TC-10G besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von SUPER MICRO Computer 6015TC-10G verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit SUPER MICRO Computer 6015TC-10G. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei SUPER MICRO Computer 6015TC-10G gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
