Benutzeranleitung / Produktwartung 3 1 5 I des Produzenten Sub-Zero
Zur Seite of 24
I NST ALLA TION &O PERA TION M ODELS 315I AND 315IP I CE M AKER.
SUB-ZERO ® is a registered trademark of Sub-Zero Freezer Company , Inc. As you follow these instructions, you will notice W ARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Sub-Zero equipment.
3 THANK Y OU Congratulations on the purchase of your Sub-Zero Model 315I ice maker (Model 315IP w ith drain pump). This restaurant-type ice maker is designed for home use. It produces the same high quality clear ice that you would e xpect from Sub-Zero.
4 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION ICE MAKER REQUIREMENTS T o properly make and store ice, the Model 3 15I(P) requires access to air , potable water , 115 V AC electrical supply and a drain. The ice maker must be installed indoors, in a controlled environment.
5 Dimensions in parentheses are in millimeters unless otherwise specified. SUB-ZER O MODELS 315I AND 315IP INST ALLA TION IMPORT ANT NOTE: The floor under the i ce maker must be at the same level as the surrounding finished floor .
Dimensions in parentheses are in millimeters unless otherwise specified. 6 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION PLUMBING REQUIREMENTS Rough in the water supply line. Connect a 1 / 4 ” O D copper line to the house supply . Be sure to use an easily accessible shut-off valve between the supply and the unit.
7 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION MODEL 315I GRA VITY DRAIN The drain and inlet water tubes must be plumbed before connecting to the ice maker . R efer to the illustrations below . All horizontal runs of drain lines must have a 1 / 4 " (6) per 12" (305) fall.
Dimensions in parentheses are in millimeters unless otherwise specified. 8 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION MODEL 315IP DRAIN PUMP 1) Place the ice maker in front of the installa- tion opening. Adjust leveling legs to the a pproximate height.
9 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION INST ALLA TION IMPORT ANT NOTE: T urn on the water supply and check all fittings for leaks. Make sure the e lectrical harness is attached to the solenoid. L et your customer know that the ice maker will not fill with water immediately and that the first batch of ice produced should be d iscarded.
Dimensions in parentheses are in millimeters unless otherwise specified. 10 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION INST ALLA TION SIDE P ANELS W ith Model 315I(P), you must securely fasten the side panels to the adjacent cabinets and floor . Panels should be fastened to the floor and walls using ’L ’ brackets (hardware not provided).
11 SUB-ZER O MODELS 315I AND 315IP INST ALLA TION INST ALLA TION DOOR P ANEL INST ALLA TION Y ou should be sure of the door panel size and placement before proceeding with the installa- tion. If you have questions, contact your S ub-Zero dealer or cabinet supplier .
12 Install the door panel by engaging the tabbed bracket to the door first and then sliding the hinge side hardware over the positioning screws. Y ou will have a 1 / 4 " inch adjustment, up and down, side to side, with this hardware.
13 Dimensions in parentheses are in millimeters unless otherwise specified. SUB-ZER O MODELS 315I AND 315IP INST ALLA TION If you are storing or disposing of your old refrigerator or freezer , please do it safely . Remove the doors or tightly secure the doors closed.
14 MODELS 315I AND 315IP FEA TURES Undercounter ice maker Model 315I has a gravity drain, while Model 315IP has a built-in pump to allow water to d rain into adjacent sink 24" (610) depth-true de.
15 SUB-ZER O MODELS 315I AND 315IP OPERA TION ICE CUBES T he ice cubes are tapered cylinders about 1 1 / 4 " (32) in diameter at the widest end; taper down to 1" (25) wide at the top; and are 1 1 / 8 " (29) h igh. When the ice maker is adjusted properly , there should be a 1 / 4 " (6) indent in the base of the cube.
16 SUB-ZER O MODELS 315I AND 315IP OPERA TION HO W THE ICE MAKER USES W A TER T he ice maker begins with a fixed charge of water that is contained in the reservoir . As the water is sprayed against the freezing surface, t he part of water that does not contain mineral impurities will freeze and stick to the ice cup molds.
17 SUB-ZER O MODELS 315I AND 315IP OPERA TION CLEANING THE ICE ST ORAGE BIN T he ice storage bin should be sanitized occa- sionally . It is usually convenient to sanitize the bin after the ice making system has been c leaned, and the ice storage bin is empty .
18 SUB-ZER O MODELS 315I AND 315IP OPERA TION ICE MAKER CLEANING CLEANING THE ICE MAKING SYSTEM 1 ) O pen the door and turn the ice maker control knob to OFF . Refer to the illustration on page 19 for location of the control knob. 2) Scoop out all of the ice; either discard it or save it in a ice chest or cooler .
19 SUB-ZER O MODELS 315I AND 315IP OPERA TION 1) Open the door and remove the control box c over . 2) Locate the cube size adjustment screw s hown in the illustration below . T o make fuller cubes, turn the screw clockwise about 1 / 4 turn. This will make the freezing cycle l onger .
20 SER VICE CENTER Contact your Sub-Zero dealer or check the Locator section of our website, subzero.com, for the authorized ser vice center near est you.
21 SUB-ZER O TROUBLESHOO TING GUIDE TROUBLESHOO TING GUIDE P R OBLEM POSSIBLE CAUSE POSSIBLE SOLUTION U nit operates I ce may be stuck in the evaporator Check water supply – filter may but no ice fa.
22 SER VICE INFORMA TION If you do need service, be sure to have the model and serial number of your unit when y ou call. Y ou’ll find these numbers on the model and serial number plate located on the left sidewall of the reservoir . For warranty p urposes, you will also need the date of installation and the name of your Sub-Zero dealer .
23 S UB- Z ERO F REEZER C OMP ANY P RODUCTS L IMITED W ARRANTY RESIDENTIAL USE ONL Y F ULL FIVE YEAR SEALED SYSTEM W ARRANTY LIMITED SIXTH THROUGH TWELFTH YEAR W ARRANTY ON THE SEALED SYSTEM FULL TWO .
17307901 8 / 2005 S UB-ZERO FREEZER COMP ANY , INC. P . O. BO X 44130 MADISON, WI 53744-4130 800-222-7820 SUBZERO .COM.
Ein wichtiger Punkt beim Kauf des Geräts Sub-Zero 3 1 5 I (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sub-Zero 3 1 5 I noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sub-Zero 3 1 5 I - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sub-Zero 3 1 5 I reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sub-Zero 3 1 5 I erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sub-Zero 3 1 5 I besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sub-Zero 3 1 5 I verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sub-Zero 3 1 5 I. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sub-Zero 3 1 5 I gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
