Benutzeranleitung / Produktwartung SFG10E des Produzenten Stow
Zur Seite of 62
OPERA TION AND P AR TS MANUAL THIS MANU AL MUST A CCOMP ANY THE EQUIPMENT A T ALL TIMES. T o find the latest revision of this publication, visit our website at: www .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 2 SILICOSIS/RESPIRA T O R Y W ARNINGS Grinding/cutting/drilling of masonry , concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 3 T ABLE OF CONTENTS Specification and part number are subject to change without notice .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 4 When or dering par ts, please supply the following infor mation: ❒ ❒ ❒ ❒ ❒ Dealer account num.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 5 NO TICE T O OPERA T ORS IF Y OU CAN NO T READ OR DO NO T FULL Y UN- DERST AND THE CONTENTS OF THIS MANU AL, PLEASE CONT A CT THE F A CT OR Y FOR PROPER ASSIST ANCE BEFORE A TTEMPTING T O OPER- A TE THIS PRODUCT .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 6 __________________ Model Number __________________ Serial Number __________________ El ectric Motor Serial Number __________________ Date of Purchase Specifications and design are subject to change without notice or obligation.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 7 The f ollowing undersigned operators of the SURF A CE GRINDER described and/or per taining to this Oper.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 8 THE FOLLO WING SAFETY PRECA UTIONS PRO VIDE SOME COMMON SENSE GUIDES T O PROMO TE SAFETY AND EFFICIENCY WITH THE SURF ACE GRINDER.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 9 exercise to restore normal blood circulation. If any of the symptoms appear , seek medical advice immediately . 7 ) Clothing must be sturdy and snug fitting, but allow complete freedom of movement.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 10 OPERA TION 1 ) Give complete and undivided attention to the job at hand. Do not chew gum, smoke and/or use smokeless tobacco while utilizing the SURF ACE GRINDER.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 11 MAINTENANCE, REP AIR AND STORA GE 1 ) Use only genuine, appro ved replacement par ts and accessories for maintenance and repair . Use of par ts and accessories manufactured by others can result in proper ty damage and/or personal injur y .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 12 ASSEMBL Y INSTRUCTIONS/OPERA TIONS Assembly The SFG10E SURF ACE GRINDER is shipped from the factory secured on a specially designed wooden pallet and protected from e xter nal damage b y a corr ugated car ton or wood crate .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 13 ASSEMBL Y INSTRUCTIONS/OPERA TIONS Operation THEOR Y OF OPERA TION The SFG10E SURF ACE GRINDERS operate on the principle of various multi-accessory attachments being utilized at rotational speeds to make direct contact with a work surf ace.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 14 inser t flails. In turn, these costs must be compared to anticipated service life. All flails will eventually wear to the point of requiring replacement.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 15 ASSEMBL Y INSTRUCTIONS/OPERA TIONS FIGURE 7 FIGURE 8 Suggested Applications: 1 ) Medium duty asphalt and concrete scarifying.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 16 Scarifier Block Bushing Scarifier block bushings are designed to be discarded whenever the flails are replaced. FIGURE 11. Normal wear should be uniform about the bushing circumference.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 17 ASSEMBL Y INSTRUCTIONS/OPERA TIONS against the inside of the SURF ACE GRINDER frame . The more aggressive flails require greater forces to keep them contained on the bloc k.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 18 shear from the concrete floor material. The occurrence is also aggra vated b y higher ambient temperatures.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 19 ASSEMBL Y INSTRUCTIONS/OPERA TIONS An insufficient seating torque value will allow the inser t to become loose fr om the unit body , resulting in premature component wear and improper scraping action.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 20 INST ALLING A MUL TI-A CCESSOR Y A TT A CHMENT (not including m ulti-segmented, dry diamond discs) IN .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 21 ASSEMBL Y INSTRUCTIONS/OPERA TIONS FIGURE 26 FIGURE 27 DANGER DANGER DANGER DANGER DANGER DO NO T OPERA TE THE SURF A CE GRINDER WITH THE 229019-017 MOUNTING WEDGES IN AN IMPROPER MOUNTING CONFIGURA TION.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 22 FIGURE 28 4 ) Return the SURF ACE GRINDER to its normal operating position. 5 ) If the machine is to be used immediately , reconnect the e xtension cord or SURF A CE GRINDER from the power source.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 23 DANGER DANGER DANGER DANGER DANGER EXERCISE EXTREME CA UTION WHEN UTILIZING A MECHANICAL DEVICE FOR LIFTING THE SURF A CE GRINDER. UTILIZE THE MECHANICAL DEVICE IN A CCORDANCE T O BOTH ITS ST A TED ST A TIC AND D YNAMIC LOADING ENVELOPES.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 24 Operating the SURF A CE GRINDER from a po wer source of improper voltage and amperage will result in un-repairable damage to the electric motor and related controls.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 25 ASSEMBL Y INSTRUCTIONS/OPERA TIONS DANGER DANGER DANGER DANGER DANGER FOR MAXIMUM PRO TECTION A GAINST A F A UL T , AL W A YS CONFIGURE THE GROUND F A UL T CIRCUIT INTERRUPTER T O BE PLUGGED INT O THE EXTEN- SION CORD.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 26 ASSEMBL Y INSTRUCTIONS/OPERA TIONS DANGER DANGER DANGER DANGER DANGER WHEN OPERA TING THE SURF A CE GR.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 27 b . Higher material removal rates can sometimes be achieved by making a series of shallow passes 90 degrees to each other to form a waffle like pattern.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 28 Failure to properly clean the interior surfaces of the SURF A CE GRINDER can result in dried material build-up and accumulation directly affecting bearing service life.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 29 but ha ve different implications f or the floor user .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 30 FIGURE 40 One of the major limitations of the F number system is that it does not control the surface regularity at joints. Because joints are statistical anomalies, the standard test method forbids measurements within 24 inches .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 31 ASSEMBL Y INSTRUCTIONS/OPERA TIONS Maintenance/Service PREVENT A TIVE MAINTENANCE CHECK LIST The normal operation of the SURF ACE GRINDER produces e xtreme dir t and dust, along with lev els of random vibration.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 32 FIGURE 41 5 ) Belt alignment is checked with the straightedge. Place the straightedge squarely against the transmission pulley . Properly aligned pulleys should also place the straightedge squarely against the motor pulle y .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 33 5 ) Remove the w or n V -belt. Inspect the electr ic motor and transmission pulleys for wear and damage. Install the replacement belt, P/N SFB45. a ) Do not install replacement belt if the pulleys have excessively worn grooves.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 34 Do not install an elastomeric mount without the use of an approved lubricant. Installation without an approved lubricant can produce tears in the mount, resulting in substandard operational performance and service life.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 35 MAINTENANCE/SER VICE 3 ) The transmission gears are lubricated at the time of assembly with approximately 24 ounces of Lubricate GR132 grease or equiv alent.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 36 T roubleshooting ELECTRIC MO TOR MO T OR F AILS TO ST ART ON/OFF s witch in the OFF position. T ur n the s witch to the ON position. SURF ACE GRINDER and/or e xtension cord is not plugged into the power source.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 37 ST ORA GE Storage Proper procedure f or long ter m storage of the SURF A CE GRINDER will protect it against the effects of corrosion and damage.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 38 Specifications STR UCTURE ................................................................... Unitiz ed, Welded Steel Plate DRIVE REDUCTION SYSTEM ......
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 39 NO TE P A GE.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 40 EXPLANA TION OF CODE IN REMARKS COLUMN The contents and part numbers listed in the parts section are subject to change without notice . Multiquip does not guarantee the availibility of the parts listed.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 41 SFG10E SURF A CE GRINDER 1 T O 3 UNITS Q t y . P/ N Description 1 ............ SF3100081 .............. CABLE, THR O TTLE 1 ............ SFSG120330 .....
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 42 OPERA T OR HANDLE ASSY . OPERA T OR HANDLE ASSY ..
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 43 OPERA T OR HANDLE ASSY . OPERA T OR HANDLE ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 SFSG120180 HANDLE, LOWER 1 2 SFSG120110 HANDLE, T OP 1 3 SF3100030 TH RO TTLE, TWIST CONTR OL, PLASTIC , COMPL.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 44 ELECTRIC MO T OR ASSY . ELECTRIC MO T OR ASSY ..
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 45 ELECTRIC MO T OR ASSY . ELECTRIC MO T OR ASSY . NO . P AR T NO .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 46 WHEEL DOLL Y ASSY . WHEEL DOLL Y ASSY ..
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 47 WHEEL DOLL Y ASSY . WHEEL DOLL Y ASSY . NO . P AR T NO .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 48 FRAME ASSY . FRAME ASSY ..
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 49 FRAME ASSY . NO . PAR T NO . P AR T NAME QTY . REMARKS 1 SFSG120010 FRAME, MAIN 1 2 SFSG120360 WEIGHT .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 50 SAFETY AND DUST SHIELD ASSY . SAFETY AND DUST SHIELD ASSY .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 51 NO . PAR T NO . P AR T NAME QTY . REMARKS 1 # SFSG120230 SKIRT ASSY 1 2 # SFSG120220 B UMPER, R UBBER .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 52 SCARIFIER ASSY . SCARIFIER ASSY ..
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 53 SCARIFIER ASSY . SCARIFIER ASSY . NO . PAR T NO . P AR T NAME QTY . REMARKS 1 SSG241900012 HOUSING 1 2 29018-083 BUSHING 2 3 87052000 B O L T CARRIAGE 3/8"-16 UNC X 2-1/2 UNC , PLA TED 2 4 29019-013 W ASHER, FLA T 5/8", HEA T TREA TED .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 54 SCRAPE-R-T A CH ASSY . SCRAPE-R-T ACH ASSY ..
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 55 SCRAPE-R-T A CH ASSY . SCRAPE-R-T ACH ASSY . NO. PART NO.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 56 GRINDING BLOCK ASSY . GRINDING BLOCK ASSY ..
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 57 GRINDING BLOCK ASSY . GRINDING BLOCK ASSY . NO. PART NO. P AR T NAME QTY . REMARKS 1 SG242101010 BLOCK 1 2 SG242101030 O-RING 3 3 83040901 PIN, RET AINING, ST AINLESS STEEL 3 4 29019-017 WEDGE PLASTIC 1 5 SSG242100020 PIN, DIAMOND PURPLE 40-50 GRIT .
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 58 DECALS DECALS.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 59 DECALS DECALS NO . P AR T NO . P AR T NAME QTY . REMARKS 1 29020-045 DECAL, W ARNING 1 2 SFSP85061 DEC.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 60 P A YMENT TERMS T er ms of pa yment f or unit sales are 2% 15 days net 30 days from date of invoice unless otherwise specifically stated on our invoice. Parts invoices have terms of net 10 days.
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 61 NO TE P A GE.
OPERA TION AND P AR TS MANUAL HERE'S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED ST A TES Multiquip Corporate Office MQ Parts Department 18910 Wilmington Ave. T el. (800) 421-1244 800-427-1244 F ax: 800-672-7877 Carson, CA 90746 F ax (800) 537-3927 310-537-3700 F ax: 310-637-3284 Contact: mq@multiquip.
Ein wichtiger Punkt beim Kauf des Geräts Stow SFG10E (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Stow SFG10E noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Stow SFG10E - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Stow SFG10E reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Stow SFG10E erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Stow SFG10E besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Stow SFG10E verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Stow SFG10E. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Stow SFG10E gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
