Benutzeranleitung / Produktwartung F144 des Produzenten Stoelting
Zur Seite of 37
Futura F144 and F131 w/ Blender OWNER'S MANUAL Manual No. 513603-1 March 2005.
.
Need Part s or Service? We stock the parts you need. Our Technicians are factory trained and are certified in the Stoelting Technicare program. Model No.: _______________________ Serial No.: _______________________ Purchase Date: ____________________ Start-Up Date:____________________ CALL Distributor: _________________________ Phone No.
.
This manual provides basic information about the freezer . Instructions and suggestions are given covering its operation and care. The illustrations and specifications are not binding in detail.
.
Safety Alert Symbol: This symbol Indicates danger , warning or caution. Attention is required in order to avoid serious personal injury . The message that follows the symbol contains important information about safety .
.
T ABLE OF CONTENTS SECTION 1 - SPECIFICA TIONS .................................................................................. 1 1.1 Description .......................................................................................................
Fig. Description Page 1 Model Endura/Futura 131G Freezer ................................................................... 1 2 Specifications .................................................................................................... 1 3 W arning Label Locations .
1 1.1 DESCRIPTION The Stoelting Futura F144 and F131 w/ Blender countertop combination shake/softserve freezers are gravity fed. The freezers are equipped with fully automatic controls to provide uniform product.
2 1.2 SPECIFICATIONS MODEL FUTURA 144 COUNTERTOP COMBINATION SHAKE/SOFTSERVE GRAVITY FREEZER Dimensions: Freezer: 22" (56 cm) wide x 28" (72 cm) deep x 34.75" (88 cm) high Crated: 28" (71 cm) wide x 35 1/2" (89.4 cm) deep x 40.
3 SECTION 2 INSTALLATION INSTRUCTIONS 2.1 SAFETY PRECAUTIONS Do not attempt to operate the freezer until the safety precautions and operating instructions in this manual are read completely and are thoroughly understood. T ake notice of all warning labels on the freezer (Fig.
4 Fig. 4. Space and Ventilation Requirements 2.2 SHIPMENT AND TRANSIT The freezer has been assembled, operated and in- spected at the factory . Upon arrival at the final destina- tion, the complete freezer must be checked for any damage which may have occurred during transit.
5 Fig. 7. Floor Stand 2.4 FLOOR ST AND INST ALLA TION T o install the F144 on the floor st and, follow the step s outlined below . 1. Uncrate the floor stand and place in an upright posi tion. NOTE Detailed instructions are included with each floor stand.
6.
7 3.1 OPERA T OR'S SAFETY PRECAUTIONS SAFE OPERA TION IS NOT AN ACCIDENT ; Observe these rules: A. Know the freezer . Read and underst and the Operating Instructions. B. Notice all warning labels on the freezer . C. Wear proper clothing. A void loose fitting garments , and remove watches, rings or jewelry which could cause a serious accident.
8 WARNING High voltage will shock, burn or cause death. The OFF-ON switch must be placed in the OFF position prior to disassembling for cleaning or servicing. Do not operate machine with cabinet panels removed. B. OFF-ON SWITCH The OFF-ON switch is a two position toggle switch used to supply power to the control circuit.
9 L. BLENDER POWER SWITCH (F131 Models Only) The blender power switch is a two position toggle switch used to supply power to the blender . When the switch is in the OFF position, the agitator will not turn. When the switch is in the ON position, the agitator will be activated every time the blender activation switch is pressed.
10 Figure 13. Sanitizing Hopper Figure 14. Spigot Opened and Solution Draining D. Clean sides of hopper , mix inlet regulator and under- side of hopper cover using a sanitized soft bristle brush dipped in the sanitizing solution (Fig.
11 G . After about 6 to 10 minutes the freezer will shut off and the green lens will illuminate. The product will be ready to serve. Freeze down time may be longer for some frozen diet dessert mixes. High ambient temperatures may extend freeze down time.
12 B. Place the OFF-ON rocker switch in the ON position and push the CLEAN switch to rotate the auger . Allow the mix to agitate in the freezer barrel until the mix has become a liquid, about 5 minutes. C. Drain the liquid mix by opening the spigot. A bucket or container should be placed under the spigot to catch the liquid mix (Fig.
13 Figure 20. Auger Flight Wear and Front Auger Support Bushing Wear D. Place the OFF-ON switch in the OFF position. T o disassemble the freezer , refer to the following steps : A. Remove the mix inlet regulator from the hopper by pulling straight up.
14 J . Remove the rear seals. K. Remove all O-rings from parts by first wiping off the lubricant using a clean paper towel. Then squeeze the O-ring upward with a dry cloth (Fig. 25). When a loop is formed, roll out of the O-ring groove. CAUTION Do not use any type of sharp object to remove O- rings.
15 D. Screw the springs onto the studs in plastic flights. Springs must be screwed into the flights com pletely to provide compression (Fig. 26). CAUTION Do not place the mix inlet regulator into the hopper before inst alling the auger . Attempting to inst all the auger with mix inlet regulator in place will damage the mix inlet regulator .
16 3.12 ROUTINE CLEANING T o remove spilled or dried mix from the freezer exterior , simply wash in the direction of the finish with warm soapy water and wipe dry .
17 3. SANITIZING – After the machine has been cleaned and contains no milkstone, the machine is reassembled. Then a FDA approved sanitizing solution is run through the machine to kill bacteria.
18 D. QUARTERLY W ARNING High voltage will shock, burn or cause death. Turn off and lock out main power disconnect before servicing. Do not operate machine with cabinet panels removed. The air-cooled condenser is a copper tube and aluminum fin type. Condensing is totally dependent upon airflow.
.
20.
21 SECTION 4 TROUBLESHOOTING CHARTS M E L B O R P E S U A C E L B I S S O P Y D E M E R s e o d r e z e e r F . n u r t o n . f f o s i r e z e e r f o t r e w o P . 1 . d e p p i r t r o n w o l b f i t i u c r i c r o e s u F . 2 . ) n r u t t o n l l i w r e g u a ( p u - e z e e r F .
22 s e o d t c u d o r P . e s n e p s i d t o n . r e p p o h n i x i m o N . 1 s i e b u t r o t a l u g e r t e l n i x i M . 2 . d e g g u l p d e d e e n r o t a l u g e r t e l n i x i m l a i c e p S . 3 . d e s u g n i e b x i m r o f g n i e b s i r e z e e r f f o y t i c a p a C .
23 ERROR CODE SYSTEM *Refer to Page 19 for Troubleshooting. ** If the Clean switch is operated three times within 10 seconds, this will cause the Push-T o-Freeze light to flash and the clean function will be disabled for 10 minutes. The power switch must remain on or the 10 minute timer will not time out.
24.
25 SECTION 5 REPLACEMENT PARTS 5 . 1 HOW TO ORDER PARTS To assure receipt of the proper replacement parts, supply your dealer or distributor with the following information: A . Model number of equipment. B . Serial number of model, stamped on nameplate.
26 Item No. Part No. Description Qt y . 1 2183047 Front Door Only 1 2177072 1.5" S pigot Extension 2177073 2.5" S pigot Extension 2177074 3" S pigot Extension 2 482019 Circular Door Kno.
W ARRANTY SOFT SER VE / SHAKE FREEZERS 1. Scope: Stoelting, LLC warrants to the first user (the “Buyer”) that the freezer cylinders, hoppers, compressors, drive motors, speed reducers, auger and a.
Ein wichtiger Punkt beim Kauf des Geräts Stoelting F144 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Stoelting F144 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Stoelting F144 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Stoelting F144 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Stoelting F144 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Stoelting F144 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Stoelting F144 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Stoelting F144. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Stoelting F144 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
