Benutzeranleitung / Produktwartung IDM2 des Produzenten Acer
Zur Seite of 28
,'0+RXVLQJ ,QVWDOODWLRQ*XLGH.
Installation Guide ii &RSU LJKW Copyright 1998 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retriev al system, or .
IDM Housing iii ,03257$176$)(7< ,16758&7,216 1. Read these instructions carefully. Save these instructions for future reference. 2. Follow all w arnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning.
Installation Guide iv 10. If an extension cord is used w ith this product, make sure that the total ampere rating of the equipment plugged into the ex tension cord does not exceed the ex tension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed 15 amperes.
IDM Housing v 16. Use only the proper type of pow er supply cord set (prov ided in your keyboard/manual accessories box ) for this unit. It should be a detachable type: UL listed/CSA certified, type SVT /SJT, rated 6A 125V minimum, VDE approved or its equivalent.
Installation Guide vi )&&&ODV V%5D GLR )UHTXHQF ,QWHUIHUHQFH6WDWHPHQW Note: This equipment has been tested and found to comply w ith the limits for a Class B digital device, pursuant to Part 15 of FCC R ules.
IDM Housing vii $ERXWWKLV0DQ XDO Purpose This manual aims to give y ou all the information you need to install the system housing. Conventions The follow ing conventions are used in this manual: NOTE Gives bits and pieces of additional information related to the current topic.
Installation Guide viii.
IDM Housing ix 7DEOHRI&RQ WHQWV 1 Introduction ................................................................................ 1 2 Standalone Sy stem .................................................................... 1 3 Features ........
IDM Housing 1 1 Introduction This installation guide describes the features of the IDM housing and tells you how to install the basic sy stem components such as disk drives, a sy stem board, or ex pansion boards. Descriptive illustrations accompany the installation procedures.
Installation Guide 2 3 Features 3.1 Front Panel Keyloc k Panel Door.
IDM Housing 3 3.2 Rear Panel Power Suppl y Power Socket COM por t slot s Expansi on P or t Slot s Expansi on S lots SCSI E x pansion Slots Housing Fan Syst em Boar d connector s.
Installation Guide 4 3.3 Internal Structure The figure below shows the housing internal structure and some of the basic system components. Power Suppl y Backpl ane B oar d Hot-Sw ap Cag e (SCSI ) 5.25-inch Dri v e B ays Expansi o n Card Slot s Housing Fa n 3.
IDM Housing 5 4 Opening the Housing Panel s 4.1 Front Panel Unlock the housing with the key and then pull the panel to access the drive trays. Keyloc k.
Installation Guide 6 4.2 Left Panel To remove the left panel: 1. Use a screw driver to remove the tw o screw s securing it to the rear panel. 2. Pull the panel handle to slide the left panel open.
IDM Housing 7 5 Installing Disk Drives and Hot-Sw ap Cage Turn off the power switch and unplug the power cord before installing or removing diskette drives. 5.1 3.5-inch Drive 1. Open the front panel and remove the left panel of the housing. See section 4 for more information on opening the housing panels.
Installation Guide 8 4. Insert the drive into the drive bay and secure it with tw o screws. 5. Connect the diskette drive cables. 5.2 5.25-inch Driv es You may install a C D-RO M, digital audio tape (D AT), hard disk, diskette drive or any other 5.25-inch device into the driv e bay.
IDM Housing 9 4. Insert the drive into the drive bay and secure it with tw o screws. 5. Connect the signal and power cables to the driv e. 5.3 Hot-Swa p Cage The hot-sw ap cage box includes the follow.
Installation Guide 10 2. Attach the driv e guides on the sides of the hot-sw ap cage w ith two screws on each side. 3. Insert the hot-swap cage into the housing and secure the hot-swap cage with tw o screws.
IDM Housing 11 4. Attach the power cable, the SCSI term inator, the HDD fault L ED cable , and the system board connector cable to the backplane board and attach the other end of the connector cable to the system board. For the location of the SCSI connector, please refer to the system board manual.
Installation Guide 12 Cascading Hot-swap Cage Configuration The SCSI connector cable and the three- connector HDD fault LED cable is an optional item needed for installing two hot-swap cages.
IDM Housing 13 SCSI Connector Cable 5.4 Hard Disk Driv e Tray 1. Use your finger to release the drive tray as shown below and then pull it out. 2. Place a hard disk on the tray. Secure it with four screws and four metal support braces as shown below .
Installation Guide 14 4. Insert the tray into the hot-swap cage and then close the lever as shown below. 6 Installing a Sy stem Board The housing accommodates various sy stem board sizes. Y ou can rearrange the pegs on the system board plate to fit the board that you w ish to install.
IDM Housing 15 7 Installing an Expansion Board 1. Remove an ex pansion slot bracket cover. Sav e the screw to secure the expansion board. 2. Align an expansion board w ith the open slot and insert the golden fingers into the expansion bus connector. 3.
Installation Guide 16 8 Install i ng a CPU or M emor y Board Follow these steps to install a CPU or memory board if your sy stem board does not include them. 1. Remove a bracket opposite the CPU or memory board slot. 2. Insert the board into the slot.
IDM Housing 17 5. Insert the right end of the bar into the hole near the hard disk driv e frame and the left end into the hole on the rear panel. Left End Right End.
Installation Guide 18 9 LVD SCSI Backplane Board The LVD SCSI hot-sw ap cage includes a hot plug SCA single-ended backplane, LED board, and the hard drive cage itself. It supports three 1-inch SCA-II SCSI hard drives in one channel w ith active terminator built-in.
IDM Housing 19 Connector Description CN7 Slot 2 CN8 SCSI 68-pin connector - Out CN9 Slot 3 JP5 Power connector S1 Slot 1 ID switch S2 Slot 2 ID switch S3 Slot 3 ID switch.
Ein wichtiger Punkt beim Kauf des Geräts Acer IDM2 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Acer IDM2 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Acer IDM2 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Acer IDM2 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Acer IDM2 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Acer IDM2 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Acer IDM2 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Acer IDM2. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Acer IDM2 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
