Benutzeranleitung / Produktwartung MDX-CA680 des Produzenten Sony
Zur Seite of 64
SERVICE MANUAL FM/AM (MW/L W) MINIDISC PLA YER US Model MDX-CA680X AEP Model UK Model MDX-CA680/CA680X SPECIFICA TIONS MDX-CA680/CA680X Photo: MDX-CA680X (US model) V er 1.1 2001.05 9-870-242-12 Sony Corporation 2001E0500-1 e V ehicle Company C 2001.5 Shinagawa T ec Service Manual Production Gr oup U .
2 MDX-CA680/CA680X Notes on chip component replacement • Ne ver reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Flexib le Circuit Boar d Repairing • Kee p the temperature of the soldering iron around 270 ˚C dur- ing repairing.
3 MDX-CA680/CA680X SECTION 1 GENERAL This section is e xtracted from instruction manual. Location of controls Refer t o the page s listed for deta ils.
4 MDX-CA680/CA680X u DISC/PRESET buttons (+/ – ) 9, 11 13, 14, 18 8, 10, 11, 12 , 13, 17, 18, 21 v SEEK buttons ( – /+) 9 13, 14, 16 8, 10, 12, 18 , 20, 21 AF TA OFF D S MENU LIST SOUND ENTER D I S C / P R E S E T SEEK SEEK DISPLA Y O PE N S C R O L L PTY (SEEK) (–):to se lect leftwards/ .
5 MDX-CA680/CA680X TV tuner unit * Syntoniseur de télévision * BUS CONTROL IN BUS AUDIO IN Source selector * Sélecteur de source * * not supplied non fournis Cautions (US model) • This unit is designed for negative ground 12 V DC operation only .
6 MDX-CA680/CA680X Précautions • Cet appareil est exclusivement conçu pour fonctionner sur une tension de 12 V CC avec masse négative. • Evitez de fixer des vis sur les câbles ou de coincer ceux-ci dans des pièces mobiles (par exemple, armature de siège).
7 MDX-CA680/CA680X L R AUDIO OUT FRONT AUDIO OUT REAR BUS AUDIO 13 57 24 68 57 48 3 Cautions • This unit is designed for negative earth 12 V DC operation only . • Do not get the wires under a screw , or caught in moving parts (e.g. seat railing). • Before making connections, turn the car ignition off to avoid short circuits.
8 MDX-CA680/CA680X Precautions • Choose the installation location carefully so that the unit will not interfere with normal driving operations. • A void installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as in direct sunlight or near heater ducts.
9 MDX-CA680/CA680X Power (AEP, UK models) connection diagram Auxiliary power connector may vary depending on the car. Check your car’s auxiliary power connector diagram to make sure the connections match correctly. There are three basic types (illustrated below).
MDX-CA680/CA680X 10 FRONT P ANEL ASSY (Note 3) 2-9. LO MO TOR ASSY (LO ADING) (M903) (P age 14) 2-10. LEVER (LE23) ASSY (P age 14) 2-11. HOLDER ASSY (P age 15) 2-12. CHUCKING ARM ASSY (P age 15) 2-13. OPTICAL PICK-UP (KMS-241C) (P age 16) 2-14. SL MO T OR ASSY (SLED) (M902), SP MO TOR ASSY (SPINDLE) (M901) (P age 16) 2-2.
MDX-CA680/CA680X 11 2-3. MECHANISM DECK (MG-164MA-138) 2-4. MAIN BO ARD 1 screw (PTT2.6 × 4) 5 mechanism deck (MG-164MA-138) 3 two screws (PTT2.6 × 4) 4 brack et (MD) 2 connector (CNP301) 1 screw (PTT2.6 × 4) 1 three ground point screws (PTT2.6 × 6) 2 three screws (PTT2.
MDX-CA680/CA680X 12 2-5. HEA T SINK 2-6. SER V O BO ARD 1 screw (PTT2.6 × 10) 1 two screws (PTT2.6 × 10 ) 2 two screws (PTT2.6 × 16) 3 heat sink 2 two screws (BVTT2 × 4) 1 optical pick-up flexible.
MDX-CA680/CA680X 13 2-7. MD CO VER ASSY 2-8. FLO A T BLOCK 3 MD cover assy 2 Pushing the cassette holder in the direction of the arrow A with a screwdriver, etc., disengage the shaft (MD cover guide) from the slot in the MD cover assy. Note : Take care not to scratch the optiocal pick-up when pushing the cassette holder with a screwdriver.
MDX-CA680/CA680X 14 2-9. LO MO T OR ASSY (LO ADING) (M903) 2-10. LEVER (LE23) ASSY 4 Remove the bracket (LO) in the direction of the arrow A . bracket (LO) 1 Remove solders of motor (M903).
MDX-CA680/CA680X 15 2-11. HOLDER ASSY 2 type-E stop ring 1.5 2 type-E stop ring 1.5 3 lever (lock L) 2 type-E stop ring 1.5 2 type-E stop ring 1.5 4 Remove the holder assy in the direction of the arrow. 1 spring (chucking) 1 spring (chucking ) 3 lever (lock R) 2-12.
MDX-CA680/CA680X 16 2-13. OPTICAL PICK-UP (KMS-241C) 6 bearing (SL) 5 feed screw assy 3 screw (K2 × 3) 2 guide shaft (OPT L) 1 two screws (K2 × 3) 7 optical pick-up (KMS-241C) 4 screw (B2 × 3) 2-14. SL MO T OR ASSY (SLED) (M902), SP MO T OR ASSY (SPINDLE) (M901) 4 screw (P1.
17 MDX-CA680/CA680X SECTION 3 ELECTRICAL ADJUSTMENTS TEST MODE This set hav e the test mode function. <Set the T est Mode> 1. Turn ON the r egulated po wer supply . (The clock is displayed) Note: Press the [OFF] button, if the clock is not displayed.
18 MDX-CA680/CA680X IC101 PCM1718E/2K IC301 CXD2662R SECTION 4 DIA GRAMS • IC Block Diagrams – SER V O Board – INPUT INTERFACE DIGITAL FILTER 5 LEVEL DAC LOWPASS FILTER CMOS AMP 1 XTI 2 DGND 3 V.
19 MDX-CA680/CA680X IC302 CXA2523AR –1 –2 + – IVR BB + – IVR AA + – IVR CC + – IVR DD + – IVR + – EE EE' EFB TESW PTGR 48 MORFO 47 MORFI 46 RFO 45 OPN 44 OPO 43 ADDC 42 COMPP 41 C.
20 MDX-CA680/CA680X IC303 BH6518FS-E2 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 123456789 10 11 12 13 14 15 16 GND VG IN4R IN4F VM4 OUT4F PGND4 OUT4R VM34 OUT3R PGND3 OUT3F VM3 IN3F IN3R PSB CAPA – CAPA+ IN2R IN2F VM2 OUT2F PGND2 OUT2R VM12 OUT1R PGND1 OUT1F VM1 IN1F IN1R V DD CHARGE PUMP.
21 MDX-CA680/CA680X 34 35 36 37 38 39 40 41 42 43 44 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 16 15 14 13 12 1 2 3 4 5 6 7 8 9 10 11 INPUT MULTIPLEXER MAIN SOURCE SELECTOR MIXING SELECTOR SECON.
22 MDX-CA680/CA680X IC51 SAA6588T -118 SCOUT MRO MPTH TCON OSCO OSCI VSSD VDDD DAVN SDA VREF MPX VSSA VDDA AFIN MAD PSWN SCL 2 1 6 15 11 13 16 14 12 INTERFACE REGISTER SIGNAL QUALITY DECODER CLOCKED C.
MDX-CA680/CA680X 23 23 4-1. BLOCK DIA GRAM – SER V O Section – F C B D A E I J J I B A C D E F DETECTOR J I A B C D E F LD PD LASER DIODE ILCC RM OPTICAL PICK-UP BLOCK (KMS-241C) AUTOMATIC POWER CONTROL Q302 APC PD APCREF AT AMP B.
MDX-CA680/CA680X 24 24 4-2. BLOCK DIA GRAM – TUNER Section – 1 2 ANT-FM ANT-AM 2 VSM 14 S-METER 10 MPX 8 AM-DET 9 RDS-DET FM/AM TUNER UNIT TU10 SYSTEM CONTROLLER IC501 (1/3) 17 SDA (EEPROM) J10 (FM/AM ANTENNA IN) 5 VCC (8.5V) TUNER +8.7V 16 VDD (5V) TUNER +5.
MDX-CA680/CA680X 25 25 12 9 5 DATA DADT VOUTL VOUTR DADT, BCK, LRCK, FS256 6 BCK BCK LRCK R-CH R-CH 1 XTI 15 17 16 RSTB DM1 DM0 LRCK FS256 DEEMP AM MPX DATA, CLOCK S-METER 30 29 1 11 20 3 SEL FD1L+ AM.
MDX-CA680/CA680X 26 26 4-4. BLOCK DIA GRAM – BUS CONTROL/PO WER SUPPL Y Section – U-COM +5V RESET SIGNAL GENERATOR IC602 REMOTE CONTROL RECEIVER IC971 BATTERY DETECT Q701 ACCESSORY CHECK Q631 6 8 4 CLK ANT+B TU8.7V AMP+B REGULATOR IC601 COM8V TU5.
27 MDX-CA680/CA680X Note on Printed Wiring Board: • X : par ts extr acted from the component side. • Y : par ts extr acted from the conductor side. • z : Through hole. • f : inter nal component. • : Pattern from the side which enables seeing.
28 MDX-CA680/CA680X • Circuit Boards Location SUB board SENSOR board SER VO boar d MAIN board KEY board.
MDX-CA680/CA680X 29 29 IC301 CN102 IC302 100 26 50 1 1 4 8 5 76 75 51 25 IC303 1 16 32 17 20 13 12 1 25 36 24 48 37 1 IC501 IC401 IC304 IC502 CN101 C308 R320 R318 C305 R319 C306 R324 R327 R328 C310 R3.
MDX-CA680/CA680X 30 30 4-7. SCHEMA TIC DIA GRAM – SER V O Section (1/2) – • See page 40 for W aveforms. • See page 18 f or IC Block Diagrams. • V oltages and wavef or ms are dc with respect to g round under no-signal conditions.
MDX-CA680/CA680X 31 31 4-8. SCHEMA TIC DIA GRAM – SER V O Section (2/2) – • See page 40 for Wa veforms. • See pa ge 18 for IC Block Diagram. • V oltages and wavef or ms are dc with respect to ground under no-signal conditions.
MDX-CA680/CA680X 32 32 4-9. PRINTED WIRING BO ARD – MAIN Board – • See page 28 for Circuit Boar ds Location. • Semiconductor Location Ref. No. Location D1 H-10 D21 K-2 D22 K-2 D23 J-2 D301 I-9.
MDX-CA680/CA680X 33 33 4-10. SCHEMA TIC DIA GRAM – MAIN Board (1/3) – • See page 40 for W aveform. • See page 18 for IC Bloc k Diagrams. • V oltages and wavef or ms are dc with respect to ground under no-signal (detuned) conditions.
MDX-CA680/CA680X 34 34 4-11. SCHEMA TIC DIA GRAM – MAIN Board (2/3) – • See page 40 f or W aveforms. • V oltages and wavef or ms are dc with respect to g round under no-signal (detuned) conditions.
MDX-CA680/CA680X 35 35 4-12. SCHEMA TIC DIA GRAM – MAIN Board (3/3) – • See page 18 for IC Bloc k Diagrams. • V oltages are dc with respect to ground under no-signal (detuned) conditions.
MDX-CA680/CA680X 36 36 4-13. PRINTED WIRING BO ARD – SUB Board – • See page 28 for Cir cuit Boards Location. LED810 LSW810 A1 S1 A2 K1 S2 K2 K1 S2 K2 A1 S1 A2 KA KA (Page 32) (Page 38).
MDX-CA680/CA680X 37 37 4-14. SCHEMA TIC DIA GRAM – SUB Board – (Page 35) (Page 39).
MDX-CA680/CA680X 38 38 4-15. PRINTED WIRING BO ARD – KEY Board – • See page 28 for Circuit Boar ds Location. (CA680X) LED900, 901, 913, 914 (CA680) (CA680X) LSW901-911, 914-919 (CA680) LED902, L.
MDX-CA680/CA680X 39 39 4-16. SCHEMA TIC DIA GRAM – KEY Board – • See page 40 for W aveform. • V oltages and wav eforms are dc with respect to ground under no-signal (detuned) conditions.
MDX-CA680/CA680X 40 40 • W aveforms – SER V O Board – 1 IC302 1 , 2 (I, J) (MD Pla y Mode) 2 IC302 rh (RFO) (MD Play Mode) 3 IC302 ek (RF) (MD Pla y Mode) 7 IC301 wk (XBCK) (MD Play Mode) 8 IC30.
41 MDX-CA680/CA680X 4-17. IC PIN FUNCTION DESCRIPTION • SERVO BOARD IC301 CXD2662R Pin No. Pin Name I/O Description 1 MNT0 (FOK) O Focus OK signal output to the MD mechanism controller (IC501) “H.
42 MDX-CA680/CA680X Pin No. Pin Name I/O Description 46 XRAS O Row address strobe signal output to the D-RAM (IC307) “ L ” active 47 XWE O Write enable signal output to the D-RAM (IC307) “ L ”.
43 MDX-CA680/CA680X Pin No. Pin Name I/O Description 91 SRDR O Sled servo drive PWM signal ( – ) output to the BH6518FS (IC303) 92 SFDR O Sled servo drive PWM signal (+) output to the BH6518FS (IC30.
44 MDX-CA680/CA680X • SERVO BOARD IC302 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP) Pin No. Pin Name I/O Description 1I I I-V converted RF signal I input from the optical pick-up block detector 2J I I-V converted RF signal J input from the optical pick-up block detector 3V C O Middle point voltage (+1.
45 MDX-CA680/CA680X • SERVO BOARD IC501 CXP84340-231Q (MD MECHANISM CONTROLLER) Pin No. Pin Name I/O Description 1 to 5 TIN3 to TIN7 I/O Input of the 4 × 8 matrix test keys ( “ L ” is always ou.
46 MDX-CA680/CA680X Pin No. Pin Name I/O Description 46 LINKOFF O Unilink on/off control signal output for the SONY bus “ L ” : link on, “ H ” : link off 47 UNIREQ O Data request signal output.
47 MDX-CA680/CA680X • MAIN BOARD IC501 MN101C49KTJ (US), MN101C49KTK (AEP, UK) (SYSTEM CONTROLLER) Pin No. Pin Name I/O Description 1 VREF – I Reference voltage (0V) input terminal (for A/D conver.
48 MDX-CA680/CA680X Pin No. Pin Name I/O Description 42 UNISO O Serial data output to the SONY bus interface (IC505) 43 UNISI I Serial data input from the SONY bus interface (IC505) 44 UNICKO O Serial.
49 MDX-CA680/CA680X 5-1. GENERAL SECTION SECTION 5 EXPLODED VIEWS The components identified by mark 0 or dotted line with mark 0 are critical for safety . Replace only with part number specified. • Items marked “*” are not stocked since they are seldom required for routine service.
50 MDX-CA680/CA680X 5-2. FR ONT P ANEL SECTION Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 X-3380-080-1 KNOB (VOL) ASSY (CA680X) 51 X-3380-081-1 KNOB (VOL) ASSY (CA680.
51 MDX-CA680/CA680X 5-3. MECHANISM DECK SECTION-1 (MG-164MA-138) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 101 A-3326-729-A SERVO BOARD, COMPLETE * 102 X-3379-367-1 C.
52 MDX-CA680/CA680X 5-4. MECHANISM DECK SECTION-2 (MG-164MA-138) M902 M901 M903 #13 #13 #14 #15 #15 #14 157 158 159 156 155 161 160 163 165 162 164 166 154 153 151 152 Ref.
53 MDX-CA680/CA680X SECTION 6 ELECTRICAL P ARTS LIST Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark KEY KEY BOARD ********** 1-694-780-11 CONDUCTIVE BOARD, CONNECTION * 3-22.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 54 MDX-CA680/CA680X LSW907 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (S, SCROLL) (CA680X) LSW907 1-786-112-11 SWITCH, KEY BOAR.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 55 MDX-CA680/CA680X R957 1-216-841-11 MET AL CHIP 47K 5% 1/16W R958 1-216-031-00 MET AL CHIP 180 5% 1/10W R959 1-216-031-00 MET AL CHIP 180 5% 1/10W R960 1-216-857-11 MET AL CHIP 1M 5% 1/16W R961 1-216-829-11 MET AL CHIP 4.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 56 MDX-CA680/CA680X C63 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V (AEP , UK) C302 1-124-233-11 ELECT 10uF 20% 16V C305 1-124-589-11 ELECT 47uF 20% 16V C307 1-162-970-11 CERAMIC CHIP 0.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 57 MDX-CA680/CA680X D612 8-719-053-18 DIODE 1SR154-400TE-25 D613 8-719-053-18 DIODE 1SR154-400TE-25 D614 8-719-053-18 DIODE 1S.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 58 MDX-CA680/CA680X R18 1-216-296-11 SHORT 0 R21 1-216-825-11 MET AL CHIP 2.2K 5% 1/16W (AEP , UK) R22 1-216-825-11 MET AL CHIP 2.2K 5% 1/16W (AEP , UK) R23 1-216-825-11 MET AL CHIP 2.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 59 MDX-CA680/CA680X R672 1-216-809-11 MET AL CHIP 100 5% 1/16W R673 1-218-871-11 MET AL CHIP 10K 0.5% 1/16W R700 1-216-809-11 MET AL CHIP 100 5% 1/16W R701 1-218-871-11 MET AL CHIP 10K 0.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 60 MDX-CA680/CA680X C514 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C515 1-107-826-11 CERAMIC CHIP 0.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 61 MDX-CA680/CA680X R519 1-216-809-11 MET AL CHIP 100 5% 1/16W R520 1-216-809-11 MET AL CHIP 100 5% 1/16W R521 1-216-809-11 ME.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 62 MDX-CA680/CA680X PAR TS FOR INSTALLA TION AND CONNECTIONS ************************************** 501 X-3373-602-1 FRAME ASS.
63 MDX-CA680/CA680X MEMO.
MDX-CA680/CA680X REVISION HIST OR Y Clicking the ver sion allows y ou to jump to the revised page. Also, clicking the v ersion at the upper right on the re vised page allows you to jump to the ne xt revised page. V er . Date Description of Revision 1.
Ein wichtiger Punkt beim Kauf des Geräts Sony MDX-CA680 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sony MDX-CA680 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sony MDX-CA680 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sony MDX-CA680 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sony MDX-CA680 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sony MDX-CA680 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sony MDX-CA680 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sony MDX-CA680. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sony MDX-CA680 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
