Benutzeranleitung / Produktwartung ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M des Produzenten Snapper
Zur Seite of 28
Safety Instructions & Operator’s Manual for OUT FRONT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 0 POWER UNIT MODELS ZF2200K ZF2500K ZF2500KH MOWER UNIT MODELS ZF5200M ZF6100M MODEL NUMBER EXPLA NA.
2 IMPORTA NT SA FETY INSTRUCTIONS WARNING: This powerfu l cutting mach ine is capable of amput ating hands and f eet and can throw objects that can cause in jury and damage! Failure to comply wi th the follo wing SAFETY inst ructions coul d result in serious injury or death to the ope rator or other persons.
3 IMPORTA NT SA FETY INSTRUCTIONS PREPA RA TION (Continued From Pre vious Page) 5. Practice operatio n of machine w ith BLA DES OFF to learn controls and develop skills. 6. Check th e area to be mowed and remo ve all objects such as toys, wire, rocks, limbs and other objects that could cau se injury if thrown by blades or interfere with mowing.
4 TABLE OF CONTENTS SECTION 1 - IMPORTA NT SA FETY INSTRUCTIONS .......................... 2-3 TA BLE OF CO NTENTS ............................................................................ 4 SECTION 1 – FA MILIA RIZA TION ........................
5 Section 1 - FA MILIA RIZA TION FIGURE 1.1 1. 1 INT RODUCTION This manual has been prepar ed for the operator’s of the SNAPPER O UT FR ONT Z-R IDER. Its purpose, as ide from recom mending s tandard operating procedures and routine s ervice requirem ents, is to prom ote SAFET Y through the use of accepted oper ating practices.
6 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-STA RT CHECK LIST Make the following chec ks and perf orm the service required bef ore each start-up. 2.1.1. Check tires and add or releas e air as needed to bring pressure in dr ive tires to: 12 psi (T urf T y pe Tires ), 5 psi ( All Terr ain Type Tires) and 25 ps i in rear caster tire.
7 Section 2 - OPERA TING INSTRUCTIONS 2.2 STA RT ING & STOPPING – ENGINE, BLA DES & PA RKING BRA KE This mac hine is equipped with dual hy dros tatic wheel drive transm issions. Each trans mission is controlled by a single motion c ontrol lever or joystick.
8 Section 2 - OPERA TING INSTRUCTIONS 2.2. STO PPING ENGINE 2.2.1. ENGINE 1. Stop engine by turning k ey to the “OFF” position. Move engine speed control to turtle “SLOW ” position and key to “STOP” position. See Figure 2.6. WA RNING DO NOT leave machine with engine running.
9 Section 2 - OPERA TING INSTRUCTIONS 2.3 OPERA TION – M OTION CONT ROL 2.3.1 DRIVING MACHINE IMPO RTA NT : The joystick lever has to be m anually mo ved to propel machine. Always return the j oy stick with hand assistance to the neutral pos ition to stop ma chine.
10 Section 3 – MA INTENA NCE 3.1 INTRODUCT ION To retain the quality of the SN APPER Out Front Z- Rider, use genuine SNAPPER replacem ent parts only . Contact a loc al SNAPPER dealer for parts and service assistance. For the correct part or inform ation for a par ticular SNAPPER Out Front Z- Rider, alway s m ention the model and serial number.
11 Section 3 – MA INTENA NCE 3.2.3. CHECK MOWER DRIVE BELT 1. Drive Belt Cover Removal a. Lower deck to lowest s etting. b. Rem ove four knobs that s ecure the deck cover. See Figure 3.3. c. Remove cover to gain ac c es s to deck belt. FIGURE 3.3 2.
12 Section 3 - MA INTENA NCE 3.3.3. RIDING MOWER - LUBRICATION 1. Front & Rear Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, f rom a gr ease gun. See Figure 3.5. FIGURE 3.5 2. Transaxle Check the level of fluid in both of the fluid reservoir s.
13 Section 3 – MA INTENA NCE 3.5 A NNUALLY (END OF EA CH SEA SON) (Continued from previous P age) 3.5.2. FUEL FIL TER Service f uel filter as instr ucted below. Turn k ey to “OFF ” pos ition. Engine MUST be stopped and MUST be cold befor e removing f ilter.
14 Section 4 - A DJUSTMENTS & REPA IR DA NGER Exercise EXT REME CAUTION w hen making this adjustment, due to clos e proximity of moving parts. 4.1 NEUTRA L POSITION ADJUS T MENTS The j oy stick controls the movem ent and stopping of the mac hine. Move the joy stic k to the center or neutral position to stop m achine.
15 Section 4 - A DJUSTMENTS & REPA IR 4.2.1. M OWER DECK A DJUSTM ENT (Continued) 7. Turn ball joint in or out until ball joint anchor hole aligns with mounting hole. Reinstall bolt and tighten s ecurely . Us e sam e procedure on other cas ter w heel.
16 Section 4 - A DJUSTMENTS & REPA IR 4.5 MOW ER BLA DE REPAIR/REPLA CEM ENT 4.5.1. BLA DE WEAR LIMIT S 1. Inspect blade frequently for signs of excess ive wear or damage. See Figure 4.5. FIGURE 4.5 WA RNING DO NOT use a cut ting blade that sh ows signs of excessive w ear or d amage.
17 Section 4 - A DJUSTMENTS & REPA IR 4.6.2. ENG INE BELT REPLACEMENT 1. Route belt around blade pulleys and idler pulley in sam e the position as old belt was rem oved. It may be necessary to use a pry bar to pull idler pulley back to ins tall belt.
18 Section 4 - A DJUSTMENTS & REPA IR 4.7.4. BA T TERY TEST ING There ar e two ty pes of battery tests : Unloaded and Loaded. T he unloaded tes t is the procedure that will be disc us sed. It’s the sim plest and mos t comm only used. An unloaded test is m ade on a battery w ithout discharging current.
19 Section 4 - A DJUSTMENTS & REPA IR 4.8 MO WER SPINDLES (Field Serviceable Spindles) BEA RING REPLACEMENT In the event that a spindle bearing requir es replacem ent, the SNAPPER Field Serviceable Spindles have been designed so that no special tools or pres ses are required.
20 TROUBLESHOOTING PROBL EM PROBA BLE CA USE CORRECTIVE A CTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. C l ean and check connections for good contact.
21 TROUBLESHOOTING PROBLEM PROBA BLE CA USE CORRECTIVE A CTION Tractor Will Not Move Or 1. Joystick in the neutral “N” position. 1. Place joystick in desired speed position. Loss Of Traction 2. Ro ll r el e as e lever is in “ RO LL ” po s it io n .
22 SERVICE SCHEDULE ITEM SERVICE PERFO RMED REF. EA CH USE 5 HRS 25 HRS 50 HRS 100 HRS EA CH SEA SON Engine Oil Check Oil Level Page 6 X Initial Oil Change Page 10 X Periodic Oil Change Page 11 X* A ir Pre-Cleaner Clean Sponge Elem ent Engine Manual X** A ir Cleaner Clean or Replace Engine Manual.
23 2 YEA R LIMITED WARRA NTY For two (2) y ear s from purchase date f or the original purchaser 's use, SNA PPER , thr ough any author iz ed SNA PPER dealer will replace, f ree of charge ( except.
24 PRIMA RY MA INTENA NCE.
25 PRIMA RY MA INTENA NCE.
26 PRIMA RY MA INTENA NCE.
27 PRIMA RY MA INTENA NCE.
28 Safety Instructions & Operator’s Manual for OUT FRONT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 0 IMPORTANT Snapper products are built using engines that meet or exceed all a pplicable emissions requirements on the date manufactured. The labels on thos e engines contain very important emissions infor mation and critical safety warnings.
Ein wichtiger Punkt beim Kauf des Geräts Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
