Benutzeranleitung / Produktwartung CP215518HV, CP216018KWV, CRP216018KWV des Produzenten Snapper
Zur Seite of 32
Safety Instructions & Operator’s Manual for 21” STEEL DECK WALK MOWERS COMMERCIAL MODELS SERIES 18 MODEL NUMBER EXPLANATION C R P 21 60 18 KW V MODEL DESIGNATION ENGINE DESIGNATION RECYCLING M.
2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons.
3 IMPORTANT SAFETY INSTRUCTIONS SAFE HANDLING OF GASOLINE (Continued From Previous Page) 3. DO NOT remove fuel cap or add fuel w ith the engine running.
4 IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE AND STORAGE (Continued From Previous Page) 9. Mow er blades are sharp and can cut. Wrap the blades or w ear heavy leather glov es and use CAUTION w hen handling them. 10. DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.
5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...................................................................... 2 - 4 TABLE OF CO NTENTS ...................................................................................................... 5 SECTION 1 - FAMI LIARIZATI ON.
6 Section 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operators of the SNAPPER WALK BEHIND MOWERS. Its purpose, aside from recommending operating and routine service requirements, is to promote safety through the use of accepted operating practices.
7 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, deflectors, grass bag, adapter and covers to make sure all are in place and securely tightened.
8 Section 2 - OPERATING INSTRUCTIONS FIGURE 2.4 5. After engine starts, turn off choke, reduce engine speed, and allow a brief warm-up until engine runs smooth. NOTE: Stop the engine (and blade) by releasing the blade control. 2.2.3. PROPELLING MOWER 1.
9 Section 2 - OPERATING INSTRUCTIONS 2. Set all wheels at the same cutting height. The highest cutting position is Notch 6. The lowest cutting position is Notch 1. See Figures 2.7 & 2.8. FIGURE 2.8 2.6 INSTALLATION of GRASS BAG ADAPTER WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running.
10 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
11 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
12 Section 3 – MAINTENANCE 3.1 INTRODUCTION To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number.
13 Section 3 – MAINTENANCE WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
14 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
15 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
16 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
17 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
18 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
19 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
20 Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug w ire and secure aw ay from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
21 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start 1. Fuel tank empty. 1. F ill fuel tank w ith fresh fuel. Using Recoil Starter 2. Engine needs choking. 2. C hoke engine by moving Engine Throttle Control fully forw ard into “Choke” position.
22 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 7 X Initial Oil Change Page 12 X Periodic Oil Change Page 13 X* Air Pre.
23 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free o.
24 PRIMARY MAINTENANCE.
25 PRIMARY MAINTENANCE.
26 PRIMARY MAINTENANCE.
27 PRIMARY MAINTENANCE.
28 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number ____________________________.
29 NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________________.
30 NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________________.
31 NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________________.
32 Safety Instructions & Operator’s Manual for 21” STEEL DECK WALK BEHIND MOWERS COMMERCIAL MODELS SERIES 18 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured.
Ein wichtiger Punkt beim Kauf des Geräts Snapper CP215518HV, CP216018KWV, CRP216018KWV (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Snapper CP215518HV, CP216018KWV, CRP216018KWV noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Snapper CP215518HV, CP216018KWV, CRP216018KWV - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Snapper CP215518HV, CP216018KWV, CRP216018KWV reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Snapper CP215518HV, CP216018KWV, CRP216018KWV erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Snapper CP215518HV, CP216018KWV, CRP216018KWV besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Snapper CP215518HV, CP216018KWV, CRP216018KWV verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Snapper CP215518HV, CP216018KWV, CRP216018KWV. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Snapper CP215518HV, CP216018KWV, CRP216018KWV gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
