Benutzeranleitung / Produktwartung FlexPWR LAN8720 des Produzenten SMSC
Zur Seite of 79
SMSC LAN8720/LAN8720i Revision 1.0 (05-28-09) DA T ASHEET Datasheet PRODUCT FEA TURES LAN8720/LAN8720i Small Footprint RMII 10/100 Ethernet T ransceiver with HP Auto-MDIX Support Highlight s Singl.
ORDER NUMBER(S): LAN8720A-CP-TR FOR 24-PIN, QFN LEAD -FREE RO HS COMPLIANT P ACKAGE (0 TO +85°C TEMP) LAN8720Ai-CP-TR FOR 24-PIN, QFN LEAD-FREE RO HS COMPLIANT P ACKAGE (-4 0 TO +85°C TEMP) Reel Size is 4000 Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 3 Revision 1.0 (05-28-09) DA T ASHEET T able of Content s Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 4 SMSC LAN8720/LAN8720i DA T ASHEET 4.8 Auto-negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 5 Revision 1.0 (05-28-09) DA T ASHEET Chapter 9 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 6 SMSC LAN8720/LAN8720i DA T ASHEET List of Figures Figure 1.1 LAN8720/LAN8720i System Block Diagram . . . . . . . . . . . . . . . . . . . .
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 7 Revision 1.0 (05-28-09) DA T ASHEET List of T ables Table 2.1 LAN8720/L AN8 72 0i 24 -P IN QFN Pinout . . . . . . . . . . . . . . . . . .
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 8 SMSC LAN8720/LAN8720i DA T ASHEET Table 6.2 100M RMII Receive Timing Valu es (50MHz REF_CLK IN ) . . . . . . . . . . . . . . . . . . . . .
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 9 Revision 1.0 (05-28-09) DA T ASHEET Chapter 1 Introduction 1.1 General T erms and Conventions The following is list o f the general terms used in this docume nt: 1.
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 10 SMSC LAN8720/LAN8720i DA T ASHEET 1.3 Architectural Overview The LAN8720/LAN8720i is compl iant with IEEE 802.3-2005 standards (RMII Pins tolerant to 3.
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 1 1 Revision 1.0 (05-28-09) DA T ASHEET Figure 1.
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 12 SMSC LAN8720/LAN8720i DA T ASHEET Chapter 2 Pin Configuration 2.
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 13 Revision 1.0 (05-28-09) DA T ASHEET T able 2.
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 14 SMSC LAN8720/LAN8720i DA T ASHEET Chapter 3 Pin Description This chapter describes the signals on each pin. When a lower case “n” is used at the beginning of the signal name, it indicates that the signa l is active lo w .
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 15 Revision 1.0 (05-28-09) DA T ASHEET 3.
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 16 SMSC LAN8720/LAN8720i DA T ASHEET 3.3 Management Signals 3.4 General Signals LED2/ nINTSEL 2I O P U LED2 – Link speed LED Indication. See Sect ion 5.
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 17 Revision 1.0 (05-28-09) DA T ASHEET 3.
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 18 SMSC LAN8720/LAN8720i DA T ASHEET Chapter 4 Architecture Det ails 4.
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 19 Revision 1.0 (05-28-09) DA T ASHEET 4.
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 20 SMSC LAN8720/LAN8720i DA T ASHEET 4.2.3 Scrambling Repeated data patterns (especially the IDLE code-grou p) can have power spectral den sities with large narrow-band peaks.
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 21 Revision 1.0 (05-28-09) DA T ASHEET 4.2.6 100M Phase Lock Loop (PLL) The 100M PLL locks on to reference clock and g enera t es the 125MHz clock used to drive the 125 MHz logic and the 100Base-Tx Tr ansmitter .
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 22 SMSC LAN8720/LAN8720i DA T ASHEET 4.3.3 NRZI and ML T -3 Decoding The DSP generates the ML T -3 recovered levels that are fed to th e ML T -3 converter .
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 23 Revision 1.0 (05-28-09) DA T ASHEET Figure 4.3 Relatio nship Between Recei ved Data and Specific MII Signals 4.3.8 Receiver Errors During a frame, unexpected co de-groups are consid ered receive errors.
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 24 SMSC LAN8720/LAN8720i DA T ASHEET In order to comply with legacy 10Ba se-T MAC/Controllers, in Half-duplex mode th e transceiver loops back the transmitted data, on the receive path.
Small Foot print RMII 10/10 0 Ethernet T ransceive r with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 25 Revision 1.0 (05-28-09) DA T ASHEET 4.5.3 10M Receive Dat a Across the MII/RMII Interface For MII, the 4 bit data nibbles are sent to the MII block.
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 26 SMSC LAN8720/LAN8720i DA T ASHEET CRS_DV toggles at 25 MHz in 100Mb/s mode and 2.5 MHz in 10Mb/s mode when CRS en ds before RXDV (i.e. the FIFO still has bits to transfer wh en the carrier event ends.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP A uto-MDIX Suppo rt Datasheet SMSC LAN8720/LAN8720i 27 Revision 1.0 (05-28-09) DA T ASHEET 4.7.1 REF_CLK In Mode A 50MHz source of REF_ CLK must be available ex ternal to the LAN8720 when using this mode.
Small Footprint RM II 10/100 Ethernet Transceive r with HP Auto-MDIX Supp ort Datasheet Revision 1.0 (05-28-09) 28 SMSC LAN8720/LAN8720i DA T ASHEET In some system architectures, a 25MHz clock source is ava ilable. The LAN8720 can be used to generate the REF_CLK to the MAC as shown in F igure 4.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 29 Revision 1.0 (05-28-09) DA T ASHEET example, only a 25MHz clock ca n be used (clock canno t be 50MHz). Simila r to the 25MHz crystal mode, the nINT function is disabled.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 30 SMSC LAN8720/LAN8720i DA T ASHEET 100M ADC (analog) 100M PLL (analog) 1.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 31 Revision 1.0 (05-28-09) DA T ASHEET 4.8.1 Parallel Detection If the LAN8720/LAN8720i is connecte d to a devic e lacking the ability to auto-negotiate (i.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 32 SMSC LAN8720/LAN8720i DA T ASHEET 4.10 nINTSEL S trapping and LED Polarity Selecti on The LED2/nINTSEL pin is used to select be tween one of two available modes: REF_CLK In Mode and REF_CLK Out Mode.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 33 Revision 1.0 (05-28-09) DA T ASHEET 4.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 34 SMSC LAN8720/LAN8720i DA T ASHEET 4.12 PHY Address S trapping The PHY ADDRESS bit is latched into an inte rnal regi ster at the end of a hardware rese t.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 35 Revision 1.0 (05-28-09) DA T ASHEET Figure 4.10 MDIO Timing a nd Frame Structure - READ Cycle Figure 4.1 1 MDI O Timing and Frame Structure - WRITE Cycle MDC MDI0 Read Cycle .
Small Foot print RMII 10/100 Ethernet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 36 SMSC LAN8720/LAN8720i DA T ASHEET Chapter 5 SMI Register Mapping T able 5.
SMSC LAN8720/LAN8720i 37 Revision 1.0 (05-28-09) DA T ASHEET Small Footprint RMII 10/10 0 Ethernet Transceiver with HP Auto-MDIX Support Datasheet T able 5.
Small Foot print RMII 10/100 Ethernet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 38 SMSC LAN8720/LAN8720i DA T ASHEET RSVD = Reserved T abl e 5.
SMSC LAN8720/LAN8720i 39 Revision 1.0 (05-28-09) DA T ASHEET Small Footprint RMII 10/10 0 Ethernet Transceiver with HP Auto-MDIX Support Datasheet T able 5.15 Special Control/St atus In dicatio ns Register 27: V endor-Specific 1 5 1 4 1 3 1 2 1 1 1 0 98765 4 3 2 1 0 AMDIXCTRL Reserved CH_SELECT Reser ved SQEOFF Reserved XPOL Reserved T able 5.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 40 SMSC LAN8720/LAN8720i DA T ASHEET The following registers a re supported (registe r numbers are in decima l): 5.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 41 Revision 1.0 (05-28-09) DA T ASHEET T able 5.21 Regis te r 0 - Ba sic Control ADDRESS NAME DESCRIPTION MODE DEFAULT 0.15 Reset 1 = sof tware reset.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 42 SMSC LAN8720/LAN8720i DA T ASHEET 1.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 43 Revision 1.0 (05-28-09) DA T ASHEET 4.9 100Base-T4 1 = T4 ab le, 0 = no T4 ability This Phy does not support 100Base-T4. RO 0 4.8 100Base-TX Full Duplex 1 = TX with full dup lex, 0 = no TX full duplex a bility RW Set by MODE[2:0] bus 4.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 44 SMSC LAN8720/LAN8720i DA T ASHEET T able 5.27 Register 6 - Auto Negotiation Expansion ADDRESS NAME DESCRIPT IO N MODE DEFAULT 6.15:5 Reserved RO 0 6.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 45 Revision 1.0 (05-28-09) DA T ASHEET 17.6 AL TINT Alternate Interrupt Mode. 0 = Primary interrupt syst em enabled (Default). 1 = Alternate interr upt system enabled.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 46 SMSC LAN8720/LAN8720i DA T ASHEET T abl e 5.3 2 Register 2 7 - Speci al Control/St atus Indications ADDRESS NAME DESCRIPTION MODE DEFAULT 27.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 47 Revision 1.0 (05-28-09) DA T ASHEET 29.1 INT 1 1 = Auto-Negotiation Page Re ceived 0 = not source of interrupt RO/ LH X 29.0 Reserved Ignore on re ad.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 48 SMSC LAN8720/LAN8720i DA T ASHEET 5.2 Interrupt Management The Management interface supports an interrupt cap ability that is not a pa rt of the IEEE 802.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 49 Revision 1.0 (05-28-09) DA T ASHEET Note: The ENERGYON bit 17.1 is defau lted to a ‘1’ at the start of the signal a cquisition process, therefore the Interrupt source fl ag 29.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 50 SMSC LAN8720/LAN8720i DA T ASHEET in repeater mode or full -duplex mode. Otherwise th e transceiver asserts CRS based on either transmit or receive activity .
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 51 Revision 1.0 (05-28-09) DA T ASHEET 5.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 52 SMSC LAN8720/LAN8720i DA T ASHEET 5.3.8.1 Near-end Loopback Near-end loopback is a mo de that sends the digital tr ansmit data back out the receive data signals for testing purpose s as indi cate d by th e blue arrows in Figure 5.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 53 Revision 1.0 (05-28-09) DA T ASHEET transmit signals an the output of the transfo rmer back to the receiver inpu ts, and this loopback will work at both 10 and 100.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 54 SMSC LAN8720/LAN8720i DA T ASHEET The MODE[2:0] hardware configuration pins are multiplexed with other signals as shown in Ta b l e 5 .
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 55 Revision 1.0 (05-28-09) DA T ASHEET Chapter 6 AC Electrical Characteristics The timing dia grams and limits in this section define th e requirements placed on the external signals of the Phy .
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 56 SMSC LAN8720/LAN8720i DA T ASHEET 6.2 RMII 10/100Base-TX/RX Ti mings (50MHz REF_CLK IN) The 50MHz REF_CLK IN timing ap plies to the case when n INTSEL is floated or pu lled-high on the LAN8720.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 57 Revision 1.0 (05-28-09) DA T ASHEET 6.2.1.2 100M RMII T ransmit Timing (5 0MHz REF_CLK IN) Figure 6 .3 100M RMII T ransm it Timing Diagram (50MHz REF_CLK IN) T able 6.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 58 SMSC LAN8720/LAN8720i DA T ASHEET 6.2.2 RMII 10Base-T TX/RX Ti mings (50MHz REF_CLK IN) 6.2.2.1 10M RMII Receive Timing (50MHz REF_CLK IN) Figure 6.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 59 Revision 1.0 (05-28-09) DA T ASHEET 6.2.2.2 10M RMII T ransmit T iming (50MHz REF_CLK IN) Figure 6.5 10M RMII T r ansmit Timing Diagram (50MHz REF_CLK IN) T abl e 6.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 60 SMSC LAN8720/LAN8720i DA T ASHEET 6.3 RMII 10/100Base-TX/RX Ti mings (50MHz REF_CLK OUT) The 50MHz REF_CLK OUT timing app lies to the case when LED/nINTSEL is pulled-low on the LAN8720.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 61 Revision 1.0 (05-28-09) DA T ASHEET 6.3.1.2 100M RMII T ransmit Timing (5 0MHz REF_CLK OUT) Figure 6.7 100M RMII T ransmit Ti ming Diagram (50MHz R EF_CLK OUT) T able 6.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 62 SMSC LAN8720/LAN8720i DA T ASHEET 6.3.2 RMII 10Base-T TX/RX Timings (50MHz REF_CLK OUT) 6.3.2.1 10M RMII Receive Timing (50MHz REF_CLK OUT) Figure 6.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 63 Revision 1.0 (05-28-09) DA T ASHEET 6.3.2.2 10M RMII T ransmit T iming (50MHz REF_CLK OUT) 6.4 RMII CLKIN Requirement s Figure 6.9 10M RMII T ransmit Timi ng Diagram (50MHz REF_CLK OUT) T able 6.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 64 SMSC LAN8720/LAN8720i DA T ASHEET 6.5 Reset T iming Figure 6.10 Reset Timing Diagram T able 6.1 1 Reset Tim ing V alues PARAMETER DESCRIPTION MIN T YP MAX UNITS NOTES T1 1.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 65 Revision 1.0 (05-28-09) DA T ASHEET 6.6 Clock Circuit LAN8720/LAN8720i can accept either a 2 5MHz cr ystal or a 25MHz single-ended clock oscillator (±50ppm) input.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 66 SMSC LAN8720/LAN8720i DA T ASHEET Chapter 7 DC Electrical Characteristics 7.1 DC Characteristics 7.1.1 Maximum Guaranteed Ratings S tresses beyond those listed in may cause permanent damage to the device.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 67 Revision 1.0 (05-28-09) DA T ASHEET no change in operation or performanc e due to the event. All pins on the LAN8720 provid e +/-5kV HBM protection.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 68 SMSC LAN8720/LAN8720i DA T ASHEET Note: The current at VDDCR is either suppl ied by th e internal regul ator from current entering at VDD2A, or fro m an external 1 .
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 69 Revision 1.0 (05-28-09) DA T ASHEET Note: The current at VDDCR is either suppl ied by th e internal regul ator from current entering at VDD2A, or fro m an external 1 .
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 70 SMSC LAN8720/LAN8720i DA T ASHEET 7.1.4 DC Characteristics - I nput and Output Buffers T able 7.6 RMII Bus Interface Signals NAME V IH (V) V IL (V) I OH I OL V OL (V) V OH (V) TXD0 0.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 71 Revision 1.0 (05-28-09) DA T ASHEET Note 7.5 These levels apply when a 0-3.3V Clock is driven into XT AL1/CL KIN and XT AL2 is floating. The maximum input voltage on XT AL1/CLKIN is VDD2A + 0.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 72 SMSC LAN8720/LAN8720i DA T ASHEET Note 7.6 Measured at the lin e side of the transformer , line replaced by 100 Ω (± 1%) resistor . Note 7.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 73 Revision 1.0 (05-28-09) DA T ASHEET Chapter 8 Application Notes 8.1 Application Diagram The LAN8720 requires few ex ternal components. T he voltage on the magnetics center tap can range from 2.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 74 SMSC LAN8720/LAN8720i DA T ASHEET 8.1.2 Power Supply Diagram 8.1.3 T wisted-Pair Interface Diagram Figure 8.3 High-Level System Diagram fo r Power Figure 8.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 75 Revision 1.0 (05-28-09) DA T ASHEET 8.2 Magnetics Selection For a list of magnetics selecte d to operate with the SMSC LAN8 720, please refer to the Ap plication note “AN 8-13 Suggested Magne tics”.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 76 SMSC LAN8720/LAN8720i DA T ASHEET Chapter 9 Package Outline Notes: 1. Controlling Unit: millimeter . 2. Dimension b applies to plated termina ls and is measured between 0.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 77 Revision 1.0 (05-28-09) DA T ASHEET Figure 9.
Small Footprint R MII 10/100 Ethe rnet T ransceiver with HP A uto-MDIX Suppor t Datasheet Revision 1.0 (05-28-09) 78 SMSC LAN8720/LAN8720i DA T ASHEET Note: S tandard reel size is 4000 pieces per reel.
Small Foot print RMII 10/10 0 Ethernet T ransceiver with HP Auto-M DIX Support Datasheet SMSC LAN8720/LAN8720i 79 Revision 1.0 (05-28-09) DA T ASHEET Chapter 10 Revision History T able 10.1 Customer R evision Hi story REVISION LEVEL & DATE SECTI ON/FIGURE /ENTRY CORRECTION Rev .
Ein wichtiger Punkt beim Kauf des Geräts SMSC FlexPWR LAN8720 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie SMSC FlexPWR LAN8720 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für SMSC FlexPWR LAN8720 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von SMSC FlexPWR LAN8720 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über SMSC FlexPWR LAN8720 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon SMSC FlexPWR LAN8720 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von SMSC FlexPWR LAN8720 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit SMSC FlexPWR LAN8720. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei SMSC FlexPWR LAN8720 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
