Benutzeranleitung / Produktwartung STC75 des Produzenten Smeg
Zur Seite of 36
INSTRUCTION MANUAL DISHWASHER.
Contents 37 1. Safety and operating instructions __________________________ 3 8 2. Installation and hook-up__________________________________ 41 3. Description of the controls ________________________________ 4 5 4. Operating instructions ___________________________________ 5 6 5.
Safety instructions 38 1. Safety and operating instructions THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULL Y READ ALL THE INSTRU CTIONS CONTAINED IN THIS MANUAL.
Safety instructions 39 THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT ( WEEE ). BY ENSURING THIS PRODUCT IS DISPOSED OF CORREC TLY.
Safety instructions 40 DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHI NG PROGRAM AND BEFORE THE DRYING CYCLE. KNIVES AND OTHER SHARP-POINTED KITCHEN UTENSILS MUST BE PLACED IN THE CUTLERY BASKET WITH THEIR TIPS FACING DOWNWARD.
Installation instructions 41 2. Inst allation and hook-up Remove the polystyrene basket retainers. Position the appliance in the desired place of installatio n. The back or sides of the dishwasher may be placed up against walls or other furniture units.
Installation instructions 42 2.1 Water supply connection Preventing the risk of clogging or damage: if the w ater pipe is new or has not been used for a long time, before connecti ng to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance.
Installation instructions 43 IF THE APPLIA NCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD: IT IS NECESSARY TO INSTALL IN THE FIXED WIRING AN ALL-POLE DISCONNECTION DEVICE HAVING A GAP BETWEEN CONTA CTS OF AT LEAST 3.5MM . AFTER INSTALLATION THE DISCONNE CTION DEVICE HAS TO BE EASY TO REACH.
Installation instructions 44 FOR UK ONLY: THIS APPLIANCE MUST BE E ARTHED. Fuse replacemen t If the mains lead of this appliance is fitted with a BS 1363 A 13amp fused plug, to change a fuse in this type of plug use a n A.S.T.A. approved fuse to BS 1362 type and proceed as follows: 1.
User instructions 45 3. Description of the controls 3.1 Upper panel All the dishwasher controls are gr ouped on the upper panel. S witch-on, programming, switch-off etc. procedures are only possible when the door is open. 1 ON/OFF BUTTON Pressing this button energises the appliance.
User instructions 46 8 "3/1" OPTION BUTTON Press this button to activate the option for use of 3/1 products. 9 "3/1" OPTION LIGHT Illuminates to indicate that the function is activated. 10 PROGRAM DELAY BUTTON Press this button to delay the start of the program by up to 9 hours.
User instructions 47 After using the table to identify the most appropriate washing program: x press the ON/OFF button (1) and wait for the PROGR AM INDICATOR LIGHT (2) to illuminate; x keep pressing .
User instructions 48 PROGRAMME DURATION CONSUMPTION (3 ) NR SYMBOL NA ME TYPE OF DISHES AND DI RT PROGRAM DESCRIPTION MINUTES (2) WAT ER ( LITRES) (1) POWER (KWh) (2) DETERGENT GRAMS 6 DISH WAR M E R .
User instructions 49 After using the table to identify the most appropriate washing program: x press the ON/OFF button (1) and wait for the PROGRAM INDICATOR LIGHT (2) to illuminate; x keep pressing t.
User instructions 50 PROGRAMME DURATION CONSUMPTION (3 ) NR SYMBOL NAME TYPE OF DISHES AND DI RT PROGRAM DESCRIPTION MINUTES (2) WATER (L I T R E S ) (1) POWER (KWh) (2) DETERGENT GRAMS 6 DISH WAR M E.
User instructions 51 The washing cycle will not take place if the dishwasher door is left open or not properly closed. TABLE FOR CERTIFICATION BODIES Reference sta ndard EN 50242 Reference program BIO Load 7 place-sett ings Type of detergent B Amount of detergent 21 g Rinse aid setting 5/6 3.
User instructions 52 CHANGING THE PROGRAM To change the program in pr ogress, simply open the door and select a new program. When the door is closed the dish washer will automatically select the new program.
User instructions 53 DELAYING THE PROGRAM (available in all programs except the soak program) The PROGRAM DELAY button (10) can be pressed to delay the start of the program by up to 9 hours . This means that the dishwasher can be operated at the time of day of your choice.
User instructions 54 ADJUSTING THE WATER SOFTENING SYSTEM N.B.: for the setting belo w to be possible, a washing program other than the soak program must be set. Press the PROGRAM DELA Y button (10) and keep it pressed until the preset value appears followed by a full stop (normally 3.
User instructions 55 If the door has to be opened while washing is in pr ogress, the progr am will be interrupted. The relativ e light will keep flashi ng and a beeper will signal that the cycle has not been comp leted. When the door is closed the program will continue from w here it was interr upted.
User instructions 56 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: x Adjust the water softening system; x Add the regenerating salt; x Add the rinse aid and deter gent.
User instructions 57 x Do not use t able sal t as it contains insoluble substances w hich, over time, may damage the water softening system. x When necessary, refill the regenerating salt container before starting the washing program .
User instructions 58 ADDING THE RINSE AID The rinse aid helps the dishes dr y faster and prevents the formation of scale deposits and staining; it is automatically added to the water during the final rinse cycle, from the container situated on the inner side of the door.
User instructions 59 ADDING THE DETERGENT After adding the detergent, to close the lid slide it i n the direction sho wn by the arrow as far as it will go then press gently to lock. During washing, the dispenser will be opened automatically. x Use only detergents specially formulated for dis hwashers.
User instructions 60 x "3/1" Products If you wish to use detergents which already contain salt and rins e aid, check whether your dishwasher is fitted with the " 3/1 o ption button " on the " Controls description " page and then refer to the section which explains how to use this function.
User instructions 61 WARNING! x Make sure that the dishes are securely in place so that they cannot tip over or obstruct the rotation of the spray arms during the washing cycle. x Do not place very small objects in the bask ets as these could fall and obstruct the spray arms or the wash pump.
User instructions 62 4.4 Using the baskets The dishwasher has a capacit y of 7 place-settings , including serving dishes. CAUTION: do not place items in positions where they pr event the detergent dispenser hatch from opening properly.
User instructions 63 The basket is fi tted with plate racks which can be stowed horizontal if required. CUTLERY BASKET Cutlery must be placed with the tips facing downward .
User instructions 64 5. Cleaning and maintenance Before carrying out any work, always disconnect the appliance from the electrical power supply. 5.1 General warnings and recommendations Avoid the use of acidic or abrasive detergents.
User instructions 65 To remove the top spray arm, take off the retainer ring-nut. Wash it in a jet of water and fit it into place correctly, checking that there are no impediments of any kind prev enting it from turning freely. CLEANING THE FILTER UNIT x The central filter C should be insp ected regularly and cl eaned if necessary.
User instructions 66 GENERAL WARNINGS AND RECOM MENDATIONS FOR CO RRECT MAINTENANCE: x The filters shou ld be cleaned under running wate r using a stiff brush. x When removing the filter , take care that there are no food residues on it. If any residues fall into the washing pit they might block hydraulic components, or foul the spray arm nozzles.
User instructions 67 If the dishes do not come out clean, check that: x the correct amount of detergent has been added; x there is regenerating salt inside the special container; x the dishes are bein.
User instructions 68 6. T roubleshooting The dishwasher is capable of signalling a n umber of faults through the simultaneous illumination of several indicator lights, with the following meanings: FAULT DE SCRIPTI ON E3 Water heating malfunction The water is not heated or the heating parameters are not correct.
User instructions 69 If an alarm occurs the appliance interrupts the program in progress and signals a fault. x Alarms E3 , E4 and E9 interrupt the current program immediately. x The E5 , E6 alarms interrupts the running program once the cause is resolved, it will bring bach the ex ecution of the program.
.
898 898 896 896 894 894 0 5 10 10 15 15 20 20 25 25 30 30 35 35 40 40 45 45 50 50 55 55 MAX MAX MIN MIN SX SX DX DX SX SX DX DX 55 55 50 50 898 898 896 896 894 894 0 5 10 10 15 15 20 20 25 25 30 30 35.
Ein wichtiger Punkt beim Kauf des Geräts Smeg STC75 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Smeg STC75 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Smeg STC75 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Smeg STC75 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Smeg STC75 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Smeg STC75 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Smeg STC75 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Smeg STC75. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Smeg STC75 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
