Benutzeranleitung / Produktwartung ID250 des Produzenten Smart Technologies
Zur Seite of 31
Sympodium TM ID250 Installation and User's Guide Interactive Pen Display.
FCC Warning This equipment has been tested and found to comply with the limits for a “Class B” digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi- dential installation.
Important Inform ation i Import ant Information Please read this manual carefully before setting up and using your Symp odium® ID250 interactive pen display . Other Precautions For proper in stallation, ob serve the following precautions. The Interactive Pen Display • Don’t place sharp or heavy objects on the ID250.
ii Important Inform ation • The refresh rate is 45 Hz to 70 Hz in XGA mode, and 45 Hz to 75 Hz in other modes. If you set the vertical refresh rate s to greater than the recommended va lues, your screen can overheat. • If you move the ID250, lift it using the fin ger indentations on the underside of the un it.
Table of Co ntents iii T abl e of Content s Important Information ................................................... .......................................... i Other Precautions ..................... ................. ................... ..........
iv Table of Co ntents Customer Support .............................................................................. .................. 21 Contacti ng SMART Techni cal Sup port .............. .................... ................ ....................
Overview 1 Overview The Sympodium® ID250 interactive pen display works with your computer and SMAR T Board™ software to create an intera ctive presentation environ ment. The ID250 inc ludes dynamic and interactive tools for cre ating presentations an d le ssons.
2 Overview Power The Sympodium ID250 intera ctive pen display uses a single 12V DC power supply , which comes with your unit, and a country-specific power cable to con nect to a power outlet. NOTE: The power input is designed for both 120V AC and 220V AC operati on.
Installing the ID250 3 Inst alling the ID250 This chapter tells you how to: • determine the best loca tion for the ID250 (this page) • connect the ID250 (p age 4) • integrate a monito r or a pro.
4 Installing the ID250 T o alleviate glare, you can use the att ached tilt stand to angle the ID250 from 8° to 73° from the horizontal. Alte rnatively , you can use a tilt stand that conforms to the st andard sizes set by the Video Electronics S tandards As sociation (VESA).
Installing the ID250 5 3. Insert the SMART Board software CD into the CD drive . For most systems, the CD is self-starting. If the CD doesn’t start automatically: – (Windows operating systems) select Star t > Run , and enter x:autorun.exe (where x: is your CD drive).
6 Installing the ID250 Matching the Resolution For the image output of the computer to display p roperly on the interactive screen, set the computer ’ s resolution to the screen’ s native resolution of 1024 x 768 pixels (XGA) and set the refresh rate to between 45 Hz an d 70 Hz.
Installing the ID250 7 The available display option s are described below . 3. With the opt ion highlighted, p ress the Enter button. 4. Use the – and + b uttons to alter the settings for the chosen option. 5. Press the Enter button to save your changes.
8 Installing the ID250 1. Press the Menu bu tton. The On Screen Display Menu opens. 2. Use the – and + buttons to select the Pitch option, and then press the Enter button. The Pitch screen appe ars. 3. Use the – and + buttons to evenly disp lay the pattern of ve rtical stripes on the screen.
Using the ID250 9 Using the ID250 The Sympodium ID250 intera ctive pen display is as easy to use as a pen on pap er . By touching the tether ed pen to the s creen, you can interact wit h computer applications intuitively . In addition, you can access ad ditional tools and features using the pen tool buttons and functio n buttons.
10 Using the ID250 Press the Lef t-Click button and then press the tip of the tether ed pen on the interactive screen to activate an object. T o double-click, press twice wi th the pen. T o drag an object, press and hold it with the tip of the pen, and drag it to it s new location.
Using the ID250 11 Using the Eraser When you press the Eraser pen tool button, you can touch the screen to remove your notes. 1. Press the Eraser button on the ID250.
12 Using the ID250.
Maintaining the ID250 13 Maint aining the ID250 Keep the unit clean, a nd replac e the pen tip when it wears down so that it doesn’t scratch the interactive screen. Cleaning the Screen Y ou should clean a heav ily used screen once a we ek because dirt and dust can stick to the screen and the pen tip.
14 Maintaining the ID250 2. Insert a new tip straight into the barrel of the pen. Push the tip firmly until it stops..
Troubleshooting 15 T roubleshooting Use this section to solve any problems that occur wit h your ID250. However , if you can’t solve your problem using these suggestions, cont act T echnical Support (p age 21). The ID250 has two light-emitting diodes (LEDs) th at indicate the system’s st atus.
16 Troubleshooting If the status light still doesn’t turn blue and your interactive pen display isn’ t responding to a touch with the pen, call T echnical Supp ort.
Troubleshooting 17 T roubleshooting Summary T able Use the following t able to solve a problem with the ID 25 0. Keep in mind that any computer tha t you use with the ID250 must be running the SMART Boar d tools for the screen to be touch sensitive.
18 Troubleshooting The white in an image doesn’t appear to be white on the screen Vide o image problem Check the video connection. Return the scr een to the factor y default s (page 6).
Waste Electrical and Electron ic Equipment (WEEE) Regulations 19 W aste Electrical and Electronic Equipment (WEEE) Regulations W aste Electrical and El ectronic Equipment (WEEE) regulati ons apply to all electrical and electronic equip ment sold within the European Union.
20 Waste Electrical and Electronic Equipment (WEEE) Regulations.
Customer Suppor t 21 Customer Support Cont acting SMART T echnical Support SMART’ s T echnical Support tea m welcomes your call. However , you may first want to contact your local reseller if you experienc e any difficulty with your SM ART product, as they may be able to solve the problem without delay .
22 Customer Suppor t General Inquiries Main Switch board: 1.888.42.SMAR T (toll-free in Canada/U.S.) or +1.403.245.0333 (all o ther countries) Fax: +1.
Index 23 Index B Backlight Setting Adjustment 7 Brightness 7 C Cable USB Length 3 Video Length 3 Care and Cleaning 13 Changing the Pen Tips 13 Color Adjustment 7 Connecting 1 , 4 Contacting Customer S.
24 Index Screen Adjusting 6 Image Problems 16 Orienting 5 Resolution 6 Troubleshooting 17 Security 8 SMART Board Software 4 SMART Board Tools 5 Status o f ID250 15 Support 21 T Temperature Ranges 3 Te.
SMART T echnologies Inc. 1207 – 1 1 Avenue SW, Suite 300 Calgary , AB T3C 0M5 CANADA Support +1.403.228.5940 or T oll Free 1.866.518.6791 (Canada/U.S.
Ein wichtiger Punkt beim Kauf des Geräts Smart Technologies ID250 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Smart Technologies ID250 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Smart Technologies ID250 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Smart Technologies ID250 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Smart Technologies ID250 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Smart Technologies ID250 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Smart Technologies ID250 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Smart Technologies ID250. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Smart Technologies ID250 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
