Benutzeranleitung / Produktwartung SI4734/35-B20 des Produzenten Silicon Laboratories
Zur Seite of 38
Rev. 1.0 4/08 Copyright © 2008 by Silicon Laborato ries Si4734/35-B20 Si4734/35-B20 B ROADCAST AM/FM/SW/L W R ADIO R ECEIVER Features Applications Description The Si4734/35 is the first digital CMOS AM/FM/SW/L W radio receiver IC that integrates the complete tuner function from antenna input to audio outpu t.
Si4734/35-B20 2 Rev. 1.0.
Si4734/35-B20 Rev. 1.0 3 T ABLE OF C ONTENT S Section Page 1. Electrical Specificat ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Typical Application Schematic . . . . . . . . . . . . .
Si4734/35-B20 4 Rev. 1.0 1. Electrical S pecifications T able 1. Recommended Operating Conditions Parameter Symbol T est Condition Min T yp Max Unit Supply V oltage V DD 2.
Si4734/35-B20 Rev. 1.0 5 T able 3. DC Characteristics (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition Min T yp Max Unit FM Mode Supply Current I FM —1 9 . 2 2 2 m A Supply Current 1 I FM Low SNR level — 19.
Si4734/35-B20 6 Rev. 1.0 Figure 1. Reset Timing Parameters for Busmode Select T able 4. Reset Timing Ch aracteristics 1,2,3 (V DD = 2.7 to 5.5 V , V IO = 1.
Si4734/35-B20 Rev. 1.0 7 T able 5. 2-Wire Control Interface Characteristics 1,2,3 (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition M in T yp Max Unit SCLK Frequency f SCL 0— 4 0 0 k H z SCLK Low Time t LOW 1.
Si4734/35-B20 8 Rev. 1.0 Figure 2. 2-Wire Control Interface Read and W rite Timing Parameters Figure 3. 2-Wire Control Interface Read and W rite Timing Diagram SCLK 70% 30% SDIO 70% 30% START START ST.
Si4734/35-B20 Rev. 1.0 9 Figure 4. 3-Wire Control Interface W rite T iming Parameters Figure 5. 3-Wire Control Interface Rea d Tim ing Parameters T able 6. 3-Wire Control Interface Characteristics (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Cond it ion Min T yp Max Uni t SCLK Frequency f CLK 0— 2 .
Si4734/35-B20 10 Rev. 1.0 Figure 6. SPI Control Interface Write T iming Parameters Figure 7. SPI Control Interface Read T iming Parameters T able 7. SPI Control Interface Characteristics (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Cond it ion Min T yp Max Uni t SCLK Frequency f CLK 0— 2 .
Si4734/35-B20 Rev. 1.0 11 Figure 8. Digit al Audio Interface T iming Parameters, I 2 S Mode T able 8. Digital Audio Int erface Characteristics (V DD = 2.
Si4734/35-B20 12 Rev. 1.0 T able 9. FM Receiver Characteristics 1,2 (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition Min T yp Max Unit Input Frequency f RF 76 — 108 MHz Sensitivity with Headphone Network 3,4,5 (S+N)/N = 26 dB — 2.
Si4734/35-B20 Rev. 1.0 13 Seek/Tune Time 6 RCLK to lerance =1 0 0p p m — — 80 ms/channel Powerup Time 6 From powerdown — — 1 10 ms RSSI Offset 12 Input levels of 8 and 60 dBµV at RF Input –3 — 3 dB T able 9. FM Receiver Characteristics 1,2 (Continued) (V DD = 2.
Si4734/35-B20 14 Rev. 1.0 T able 10. 64–75.9 MHz Input Frequency FM Receiver Characteristics 1 (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition Min T yp Max Unit Input Frequency f RF 64 — 75.9 MHz Sensitivity with Headphone Network 2,3,4,5 (S+N)/N = 26 dB — 4.
Si4734/35-B20 Rev. 1.0 15 T able 1 1. AM/SW/L W Receiver Characteristics 1 (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condition Min T yp Ma x Unit Input Frequency f RF Long Wave (L W) 153 — 279 kHz Medium Wave (AM) 520 — 1710 kHz Short Wa ve (SW) 2.
Si4734/35-B20 16 Rev. 1.0 T able 12. Reference Clock and Cryst al Characteristics (V DD = 2.7 to 5.5 V , V IO = 1.5 to 3.6 V , T A = –20 to 85 °C) Parameter Symbol T est Condit ion Min T yp Max Unit Reference Clo ck RCLK Supported F requencies * 31.
Si4734/35-B20 Rev. 1.0 17 2. T ypical Application Schematic Notes: 1. Place C1 close to V DD pin. 2. All grounds connect directly to GND pl ane on PCB. 3. Pins 1 and 20 are no connects, leave floating. 4. T o ensure proper operation and receiver performance, follow the guidelines in “AN383: Antenna Sele ction and Universal Layout Guide.
Si4734/35-B20 18 Rev. 1.0 3. Bill of Materials Component(s) V alue/Description Supplier C1 Supply bypass capacitor, 22 nF, ±20%, Z5U/X7R Murata C4 Capacitor, 18 pF, ±20%, Z5U/X7R Murata C5 Coupling capacitor, 0.47 µF, ±20%, Z5U/X7R Murata L1 Ferrite loop stick, 180 – 450 µH Jiaxin L2 4.
Si4734/35-B20 Rev. 1.0 19 4. Functional Description 4.1. Overview Figure 9. Functional Block Diagram The Si4734/35 is the indu stry's first fully integrated, 100% CMOS AM/FM/SW/L W radio receiver I C.
Si4734/35-B20 20 Rev. 1.0 4.2. Operating Modes The Si4734/35 ope rates in e ither an FM receive or an AM/SW/L W receive mode. In FM mode, radio signals are received on FMI (pin 2) an d processed by the FM front-end circuitry . In AM/SW/L W mode, radio signals are received on AMI (pin 4) an d processed by the AM front-end circuitry .
Si4734/35-B20 Rev. 1.0 21 4.7. Digit al Audio Interface (Si4735 Only) The digit al audio interface opera tes in slave mode and supports three different aud io da ta formats: I 2 S Left-Justified DSP Mode 4.
Si4734/35-B20 22 Rev. 1.0 Figure 10. I 2 S Digita l Audio Format Figure 1 1. Lef t-Justified Digit al Audio Format Figure 12. DSP Digit al Audio Format LEFT CHANNEL RIGHT CHAN NEL 1 DCLK 1 DCLK 13 2n .
Si4734/35-B20 Rev. 1.0 23 4.8. Stereo Audio Processing The output of the FM demod ulator is a stereo multiplexed (MPX) signal. The MPX st andard was developed in 1961, and is used worldwide.
Si4734/35-B20 24 Rev. 1.0 4.13. T uning The frequency synt hesizer uses Silic on Laboratories’ proven tech nology , including a com pletely integrat ed VCO. The frequency synthesizer g enerates the quadrature local os cillator signal used to downconvert the RF input to a lo w intermediate frequen cy .
Si4734/35-B20 Rev. 1.0 25 word by driving SDIO low on the next falling edge of SCLK. Although the Si4734/35 will respond to only a single device address, th is address can b e changed with the SEN pin (note that the SEN pin is n ot used for signaling in 2-wire mode).
Si4734/35-B20 26 Rev. 1.0 will be ignored by the devic e if the transaction is aborted. For details on timing specifications and dia grams, refer to Figure 6 and Figure 7 on page 10. 4.17. GPO Output s The Si4734/35 provides fi ve general-purpo se output pins.
Si4734/35-B20 Rev. 1.0 27 5. Commands and Properties T able 14. Si473x Command Summary Cmd Name Description 0x01 POWER_UP Power up device and mode selection. Modes include AM/SW/L W or FM receive, ana log or dig ital output , and re fe re nc e c loc k or cry stal suppo rt.
Si4734/35-B20 28 Rev. 1.0 T able 15. Si473x Property Summary Prop Name Description Default 0x0001 GPO_IEN Enables inte rr upt sources. 0x0000 0x0102 DIGIT AL_OUTPUT_FORMA T Co nfigures the digit al output format (Si4735 only). 0x0000 0x0104 DIGIT AL_O UTPUT_ SAMPLE_RA TE Configures th e digital outpu t sample rate in 100 Hz steps.
Si4734/35-B20 Rev. 1.0 29 0x1502 RDS_CONFIG Configures RDS setting. 0x0000 0x3100 AM_DEEMPHASIS Sets de-emphasis time const a nt. Can be set to 50 us. De- emphasis is disabled by default. 0x0000 0x3102 AM_CHANNEL_FIL TER Select s the bandwid th of the chan nel filter for AM/SW/L W recep- tion.
Si4734/35-B20 30 Rev. 1.0 6. Pin Descriptions: Si4734/35-GM Pin Number(s) Name Description 1, 20 NC No connect. L eave floating. 2F M I F M R F i n p u t s . 3 RFGND RF ground. Connect to ground plane on PCB. 4 AMI AM/SW/L W RF input. 5R S T Device reset (active low) input.
Si4734/35-B20 Rev. 1.0 31 7. Ordering Guide Part Number* Description Package Ty p e Operating Te m p e r a t u r e Si4734-B20-GM AM/FM/SW/L W Broad cast Radio Receiver QFN Pb-free –20 to 85 °C Si47.
Si4734/35-B20 32 Rev. 1.0 8. Package Markings (T op Marks) 8.1. Si4734/35 T op Mark 8.2. T op Mark Explanation Mark Method: YAG Laser Line 1 Marking: Part Number 34 = Si4734, 35 = Si4735 Firmware Revision 20 = Firmware Revision 2. 0 Line 2 Marking: Die Revisi o n B = Revision B Die TTT = Internal Code Internal tracking code.
Si4734/35-B20 Rev. 1.0 33 9. Package Outlin e: Si4734/35 QFN Figure 14 illustrates the package details for the Si4734/35. T able 1 6 lists the values for the dimensio ns shown in the illustration. Figure 14. 20-Pin Quad Flat No-Lead (QFN) T able 16. Package Dimensions Symbol Millimeters Symbol Millimeters Min Nom Max Min Nom Max A 0.
Si4734/35-B20 34 Rev. 1.0 10. PCB Land Pattern: Si4734/35 QFN Figure 15 illustrates the PCB land pattern det ails for the Si4734/35-GM. T able 17 lists t he values for the dimensions shown in the illustration.
Si4734/35-B20 Rev. 1.0 35 T able 17. PCB Land Pattern Dimensions Symbol Millimeters Symbol Millimeters Min Max Min Max D 2.71 REF GE 2.10 — D2 1.60 1.80 W — 0.34 e 0.50 BSC X — 0.28 E 2 .71 REF Y 0.61 REF E2 1.60 1.80 ZE — 3.31 f 2.53 BSC ZD — 3 .
Si4734/35-B20 36 Rev. 1.0 1 1. Additional Reference Resources EN55020 Compliance T est Certificate AN231: Si4700/01 Headphon e and Antenna Interface AN332: Universal Programming Guide .
Si4734/35-B20 Rev. 1.0 37 D OCUMENT C HANGE L IST Revision 0.4 to Revision 1.0 Updated T able 1, “Recommended Operating Conditions,” on page 4. Updated T able 3, “ DC Characte ristics,” on page 5. Updated T able 5, “2-Wire Co ntr o l Inte rf ace Characterist ics 1,2,3 ,” on page 7.
Si4734/35-B20 38 Rev. 1.0 C ONT ACT I NFORMATION Silicon Laboratori es Inc. 400 West Cesar Chavez Austin, TX 78701 T el: 1+(512) 416-8500 Fax: 1+(512) 416-9669 T oll Free: 1+(877) 4 44-3032 Email: FMinfo@silabs.com Internet: www .silabs.com Silicon Laboratories and Silicon Labs are trademarks of Silico n Laboratories Inc.
Ein wichtiger Punkt beim Kauf des Geräts Silicon Laboratories SI4734/35-B20 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Silicon Laboratories SI4734/35-B20 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Silicon Laboratories SI4734/35-B20 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Silicon Laboratories SI4734/35-B20 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Silicon Laboratories SI4734/35-B20 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Silicon Laboratories SI4734/35-B20 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Silicon Laboratories SI4734/35-B20 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Silicon Laboratories SI4734/35-B20. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Silicon Laboratories SI4734/35-B20 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
