Benutzeranleitung / Produktwartung Switch Cubes des Produzenten Signal Dynamics
Zur Seite of 23
1 Contents Introduction Page 2 Instrumentation Page 7 Operation / Function Page 9 Programming Page 18 Appendix Page 21 All Rights Reserved. Reprodu ction by any means , electronic or mech anical inclu.
2 LINX ™ Network Bus Electrical System System Overview: Simpler, easier installation and comprehensive rider information; these are the some of t he basic advantages of the LINX™ Net work Bus Wiring System.
3 Locating Rear Module The rear module is identified by its’ Black Connect or, and should be located in an area that is close t o the battery and Starter Solenoid, and also central to all of the devices it connects to. Th e module is splash proof, but sh ould be mount ed in an area t hat has some pr otection from water and heat.
4 Installing switch cubes The switch cubes a re designed to fit a 1” handlebar, a nd connect to the front brake swi tch, and clut ch switc h (optional). Installing the switch cubes involves drilling a hole in the handleb ar where the switch cube will be located, and another where the wires will connect to the d isplay module.
5 Installing the Display Module The display m odule can be mount ed either above or below the ha ndlebar by attaching the backing plate moun ting tab to a handle bar clamp (not included). The wires from the switch cubes will come out of the handlebars, into the disp lay housing, and plug into the ap propriate connector.
6 To Replace the Connector End on a Cable. 1. Strip about 1” of the outer insulation with an RJ-45 stripper/crim ping tool, the inner i nsulation does not need t o be stripped. These t ools are com monly used to crim p computer network cables, an d are avalible at m ost electronic stores.
7 Display Module: When the system is powered-on, a self-test will run and if any faults are noted, they will be displayed. After this, the logo will be displayed for 3 seconds, and then the module will enter the operational m ode.
8 • Temperature and Voltage. • System Alert text message. (If Present ) Indicators: The indicator icons are located to th e left and right sides of the LCD display screen.
9 Front (Tank) Module The following outputs and op erations are controlled by th e Front Module: • Ignition • Compression Release • NOS solenoid (optional) • Left & Right Fro nt Turns Sign.
10 Switches: The handlebar switches are designed for easy installation or removal with plug-in connector. They are also LED ba ck-lit for easier button identification during night time condition s. They provide a positive tactile click when depressed.
11 Right Handlebar Switch Module Functions Operation / Function R ight Turn Starts or cancels right turn signal function. (See tur n signal functi on below) Start Will activate the engine starter soleno id circuit if: the Run/Kill switch is set to Run, the bike i s in neutral, and the engine is not running (RPM =0).
12 Initial LINX™ Power-UP & Starting Key Switch Operation: When the key switch is turned on, power is applied to the LINX™ system and a self-test will run.
13 the start button on the right handlebar switch to initiate the eng ine starter. The starter motor can not be acci dentally engaged if the LINX™ system recognizes that the motor is already running.
14 Information & Alert Conditions Text information window: The Text information wi ndow is located at the bottom of the LCD screen. To toggles between the following items, press the (#) key on the right handlebar switch.
15 Lighting Marker Lights: Turn Signal Lights also function as marker lights. This function enables single intensity in candescent or LED bulbs to have a marker light feature. Headlight Features & Operation: Low Beam When the key switch is first turned on, the headligh t is automatically selected to lo w beam to conserve battery power.
16 Turn Signal Function: The turn signal selection buttons are lo cated on the left and right handle bar switch cubes. The t urn signals are activat ed by pressing the appropriate button. The turn signals will flash for 7 seconds then automatically cancel.
17 • Brake Lights: When the brakes are applied and the motorcycle is stopped, the brakes remain on until the bike accelerates. This will also cause the turn signals to continue to flash 10 seconds after th e bike accelerates. Circuit Protection The LINX™ system does not re quir e external fuses for circu it protection.
18 Program Mode: To enter the program mode, the bike’s run/kill switch must be in “kill” position. After selecting “kill”, the press ( * ) and ( # ) together for 5 seconds.
19 • Vehicle Identification Number - Set or V iew VIN# (Vin # may only be set once on some bikes). • View Logs - This will display a history of “events” and “faults” encountered by the system. This lo g erases the oldest message when the amount of space for storage is m axed out.
20 Voltage/Temperature are displayed) This will take you to a screen prompti ng you to press the # button at the be ginning of a measured mile . When you pass the begi nning mi le marker press the # button. The screen will then pro mpt you to press the # button at the end of the ending m ile marker.
21 System Specification: System Power 12VDC 30Amps Operating Temperatures 32 ° F to 122 ° F (0 ° C to 50 ° C) Physical Size Fron t / Rear Module 2.
.
24 One Year Limited Warranty Signal Dynamics Corporation warranties this product at time of purchase to be free from defects i n materials or w orkmanship to t he original purchaser.
Ein wichtiger Punkt beim Kauf des Geräts Signal Dynamics Switch Cubes (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Signal Dynamics Switch Cubes noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Signal Dynamics Switch Cubes - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Signal Dynamics Switch Cubes reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Signal Dynamics Switch Cubes erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Signal Dynamics Switch Cubes besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Signal Dynamics Switch Cubes verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Signal Dynamics Switch Cubes. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Signal Dynamics Switch Cubes gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
