Benutzeranleitung / Produktwartung LC-40LE731E des Produzenten Sharp
Zur Seite of 48
TINS-F204WJZZ LC-40LE730E LC-46LE730E LC-40LE731E LC-46LE731E LC-40LE732E LC-46LE732E LCD COLOUR TELEVISION LCD-F ARBFERNSEHGERÄT TÉLÉVISEUR COULEUR À ÉCRAN CRIST AUX LIQUIDES (LCD) TELEVISORE A .
LC-40LE730E LC-40LE731E LC-40LE732E LC-46LE730E LC-46LE731E LC-46LE732E 40”: ( ) 46”: [ ] 40”/46”: ([ ]) SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse.
OPERA TION MANUAL Contents ....................................................................... 1 Introduction ................................................................ 2 Dear SHARP customer ................................................. 2 Important Safety Precautions .
• Cleaning—Unplug the AC cord fr om the AC outlet before cleaning the product. Use a damp cloth to clean the pr oduct. Do not use liquid cleaners or aerosol cleaners. • Use a soft damp cloth to gently wipe the panel when it is dirty . T o protect the panel, do not use a chemical cloth to clean it.
Introduction Remote control unit AV F USB REC V S U T 6 7 5 4 3 8 9 10 12 13 14 11 2 11 6 15 17 18 19 20 21 22 23 24 1 >a (Standby/On) (Page 10) 2 AT V Access conventional analogue TV mode. DTV Access digital TV mode. SA T Access satellite mode. RADIO DTV/SA T : Switch between radio and data mode.
TV (Front view) TV (Side and rear view) Illumination led* Introduction WARNING • Excessive sound pressur e from earphones and headphones can cause hearing loss. • Do not set the volume at a high level. Hearing experts advise against extended listening at high volume levels.
Inserting the stand Insert the stand into the openings on the bottom of the TV (Hold the stand so it will not drop from the edge of the base area). Insert and tighten the four screws into the four holes on the r ear of the TV . NOTE • T o detach the stand unit, perform the above steps in reverse or der .
Preparation Inserting the batteries Before using the TV for the first time, insert the two supplied “AAA” size batteries. When the batteries become depleted and the remote contr ol unit fails to operate, replace the batteries with new “AAA” size batteries.
Quick guide 1 2 3 Initial installation overview Follow the steps below one by one when using the TV for the first time. Some steps may not be necessary depending on your TV installation and connection. Connect an antenna cable to the antenna terminal (Page 8).
Quick guide Before turning on the power In order to r eceive coded digital stations, a Common Interface Module (CI Module) and a CA Card must be inserted in the CI slot of the TV . The CI Module and the CA Card ar e not supplied accessories. They are usually available fr om your dealers.
Initial auto installation When the TV is powered on for the first time after pur chase, the initial auto installation wizard appears. Follow the menus and make the necessary settings one after another . 1 Press a on the TV . • The initial auto installation wizard appears.
W atching TV Selecting audio language E DTV/CADTV/SA T mode: Each time you press 2 the audio language switches between audio sources available. NOTE • The audio mode screen disappears in three seconds. • Selectable items vary depending on the received broadcasts.
E Select a program 1 Select the time span -Press c / d to select the time span you want to sear ch, p ress OK. • Continue to press d to display pr ograms in the next time span. 2 Select the desired program -Press a / b to select the desir ed program, p r ess OK .
Buttons for teletext operations Buttons Description P r / s Increase or decr ease the page number . Colour (R/G/ Y/B) Select a group or block of pages displayed in the coloured brackets at the bottom of the screen by pr essing the corresponding Colour (R/G/Y/B) on the remote contr ol unit.
Connecting exter nal devices E Before connecting ... • Be sure to turn off the TV and any devices before making any connections. • Firmly connect a cable to a terminal or terminals. • Carefully read the operation manual of each external device for possible connection types.
Connecting external devices The HDMI connections permit digital video and audio transmission via a connection cable from a player/ recor der . The digital picture and sound data are transmitted without data compression and ther efore lose none of their quality .
Connecting external devices NOTE • In cases when the decoder needs to receive a signal fr om the TV , make sur e to select the appropriate input terminal to which the decoder is connected in “Source List” (Page 10).
HDMI (DVI) Connection ø 3,5 mm stereo mini jack cable HDMI 1, 2, 3 or 4 HDMI-certified cable DVI/HDMI Cable PC connection Connecting a PC Analogue Connection ø 3,5 mm stereo mini jack cable VGA cable Y ou can select the picture size. 1 Press MENU on the remote contr ol,then press OK .
Resolution Horizontal Frequency V ertical Frequency VGA 640 g 480 31,5 kHz 60 Hz VGA 720 g 400 31,47 kHz 70 Hz SVGA 800 g 600 37,9 kHz 60 Hz XGA 1.024 g 768 48,4 kHz 60 Hz WXGA 1.360 g 768 47,7 kHz 60 Hz SXGA 1.280 g 1.024 64,0 kHz 60 Hz SXGA+ 1.400 g 1.
A V A A F US B RE C V S U T NOTE • "MENU" options differ in the selected input modes, but the operating procedur es are the same. • The screens in the operation manual are for explanation purposes (some ar e enlarged, others cropped) and may vary slightly from the actual screens.
Basic adjustment Picture settings When the Picture Mode is set to “User” , the pictur e can be adjusted according to your pr eferences. See the following setting table.
Audio settings When the Sound Mode is set to “User” , the sound can be adjusted according to your pr eferences. See the following setting table. Adjustments options Selected setting ◄ Button ►.
T ime settings This adjustment allows you to set or to display the following functions: Clock, Off/On Timer and Sleep T imer . ● ● Clock This function allows you to display the clock information (day / month / year / hour/ minute). The time and the date can’t be modified in this option.
Channel settings Channel Channel adjustments Allows to reconfigur e the channels after initial auto installation has been completed. ● ● Auto tuning This function allows you to select the country and automatically adjusts the channels for digital, cable, satellite (Only LE732 model series) or analogue individually .
Searching for satellite broadcasts (Only for LE732 model series) Basic adjustment ● SADTV Auto tuning Allows you to tune satellite services. 1 Press MENU on the r emote control. With ◄ / ► keys select Channel , then select Auto T uning and pr ess OK .
● Language Language Allows you to select the screens language and the audio language. ● OSD Language Press a / b/c/d to select the "Menu" language, then press OK .
Y ou can display the channel information that you are watching at this moment by pressing p on the remote control unit. Information that appears on the screen: Program number Program name .
For selecting the input type of external equipment. • If no (colour) image is displayed, try changing to another signal type. • Check the operations manual of the external equipment for the signal type. Connect an USB device to the TV as shown below .
Buttons for full screen display operation Viewing pictures on full screen Buttons Description ▲ / ▼ Cursor Go to the previous/next photo in the same directory . 6 button Go back to the previous scr een. Blue button Zoom: ▲ / ▼ / ◄ / ► allow to move through the pictures when zoom is activated.
USB / HOME MEDIA device compatibility NOTE • Progressive format jpeg files ar e not supported. • Music files in USB 1.1 devices may not be played properly . • Operation using USB hubs is not guaranteed. • The exter nal hard disc with capacity exceeding 1TB cannot be detected correctly .
HDMI devices Controlling HDMI devices using HDMI CEC E What is HDMI CEC? Using the HDMI CEC protocol, you can interactively operate compatible system devices (A V amplifier , DVD player/recor der , Blu-ray player/recorder) using a single remote contr ol unit.
HDMI devices Connecting a player/recorder only Player/Recorder HDMI-certified cable (commercially available) HDMI CEC (Consumer Electronics Control) menu Go to “Menu” > “Settings” > "Input Settings" > “HDMI CEC” and select the menu you want to set.
Connected TV What is Connected TV? Internet setup Connected TV set to play easily digital media contents coming from the Network (Internet or Home). Connected TV offers up to two dif ferent modes: E Inter net services support (BBC iPlayer (Only LE731 for UK), Y ouT ube, and HbbTV).
Connected TV Use the SHARP (AN-WUD630) USB adapter (sold separately) with the TV . ● Wireless connection overview PC (Home Media Server) Wireless LAN router/access point Wireless AN-WUD6.
Connected TV The illustrations on this page are for explanation purposes. They are subject to change without notice. E Display the start page Press NET . NOTE • When connect TV to the Inter net, a message which requests a softwar e update may display in some cases.
USB REC function USB REC function allows you to recor d a TV programme and watch it later . Also allows you to temporize one or more r ecording and they will be available for a later on view . These recor dings will not be lost when the TV is turned off.
● ● Recordings and timings 1. The timings will be stored in the USB REC Programmed r ecording list in the USB REC menu, pending to be executed. 2. All the fi nished recor dings are available on the “ USB REC Recorded list ” in the USB REC menu.
Enjoying 3D image viewing V iewing 3D images 1 Select the 3D source (HDMI). 2 Press "3D" button on Remote Contr ol. NOTE • The TV screen may temporarily become black when the TV is trying to detect a 3D image signal and when switching from 3D to 2D mode.
Enjoying 3D image viewing Configuring the TV settings to enhance 3D image viewing Y ou can adjust the brightness of the TV for 3D image viewing. 1 Press 3D button while you ar e viewing 3D image. 2 Press b to select 3D Brightness and pr ess OK. 3 T o adjust de brightness press a/b to choose between the options.
Enjoying 3D image viewing T roubleshooting - 3D Images Problem Possible solution • 3D images are not displayed. • Is “3D auto change” set to “No”? Press 3D to switch to 3D mode. • If “3D auto change” is set to “Y es” but no 3D images are displayed, check the display format of the content being viewed.
Appendix Information on the software license for this pr oduct Software composition The software included in this pr oduct is comprised of various software components whose individual copyrights ar e held by SHARP or by third parties.
Appendix T roubleshooting Problem Possible Solution • No power . • Check if you pressed TV a on the r emote control unit. If the indicator on the TV lights up red, pr ess TV a . • Is the AC cord disconnected? • Check if you pressed a on the TV .
Appendix Specifications Item 40” LCD COLOUR TV , Models: LC-40LE730E, LC-40LE731E, LC-40LE732E 46” LCD COLOUR TV , Models: LC-46LE730E, LC-46LE731E, LC-46LE732E LCD Panel 40” BLACK TFT LCD LED TV 46” BLACK TFT LCD LED TV Resolution 6.220.800 dots (1.
Appendix EU Energy Label for T elevisions On 30 November , 2010 the European Commission adopted the Commission Delegated Regulation (EU) No 1062/2010 with regard to energy labelling of televisions. The Regulation entered into force on 20 December 2010 and applies in all Member States.
Sharp LCD-TV with an EU Eco-label This product has of fi cially been awarded the Eco-label of the European Union, “The Flower” (for details see EU Commission Decision 2009/300/EC - OJ L 82/3 dated 28.3.2009). Sharp is the fi rst company to achieve this Eco-label for TVs thus demonstrating its commitment to improving our environment.
A. Information on Disposal for Users (private households) 1. In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and ele.
LC-40LE730E LC-40LE731E LC-40LE732E LC-46LE730E LC-46LE731E LC-46LE732E 40”: ( ) 46”: [ ] 40”/46”: ([ ]) SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse.
TINS-F204WJZZ LC-40LE730E LC-46LE730E LC-40LE731E LC-46LE731E LC-40LE732E LC-46LE732E LCD COLOUR TELEVISION LCD-F ARBFERNSEHGERÄT TÉLÉVISEUR COULEUR À ÉCRAN CRIST AUX LIQUIDES (LCD) TELEVISORE A .
Ein wichtiger Punkt beim Kauf des Geräts Sharp LC-40LE731E (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sharp LC-40LE731E noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sharp LC-40LE731E - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sharp LC-40LE731E reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sharp LC-40LE731E erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sharp LC-40LE731E besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sharp LC-40LE731E verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sharp LC-40LE731E. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sharp LC-40LE731E gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
