Benutzeranleitung / Produktwartung LC-13S2U, LC-15S2U, LC-20S2U des Produzenten Sharp
Zur Seite of 57
LC-13S2U LC-15S2U LC-20S2U LIQUID CR YST AL TELEVISION OPERA TION MANU AL ENGLISH ENGLISH IMPOR T ANT INFORMA TION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
2 IMPOR T ANT INFORMA TION (Contin ued) WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
3 Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years of trouble-free operation of your product, please read the Important Safety Precautions carefully before using this product.
4 ■ The Liquid Crystal panel is a very high technology product with 921,600 thin film transistors, giving you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not affect the performance of your product.
5 IMPOR T ANT SAFETY PRECA UTIONS (Continued) ■ Outdoor Antenna Grounding – If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.
6 CONTENTS Page IMPORTANT INFORMATION ....................................................................................................... 1, 2 DEAR SHARP CUSTOMER ....................................................................................
7 Make sure the following accessories are provided with the product. SUPPLIED A CCESSORIES AC Cord Antenna Cable “ AAA ” size (UM/SUM-4) Dry Battery ( × 2) AC Adapter UBATU0026GEZZ QCNWG0003CEPA .
8 PREP ARA TION Batteries for the Remote Control Before using the LCD TV set for the first time, install two ( “ AAA ” size, UM/SUM-4) batteries (supplied). When the batteries become depleted and the remote control fails to operate, replace the batteries with new ( “ AAA ” size, UM/SUM-4) batteries.
9 PREP ARA TION (Continued) ■ Before connecting cables and cords to the rear terminals, remove the terminal cover. Push in the tab and pull out the terminal cover carefully.
10 75-ohm coaxial cable 300-ohm twin-lead VHF/UHF antenna VHF/UHF antenna 300/75-ohm adapter (not supplied) 300-ohm twin-lead 300-ohm twin-lead 75-ohm coaxial cable OUT IN VHF antenna UHF antenna Combiner (not supplied) or or PREP ARA TION (Continued) A.
11 Power Connection A • Use a commercially available AC plug adapter, if necessary, depending on the design of the wall outlet. • Always turn the MAIN POWER switch of the LCD TV set to off when connecting the AC adapter. • Unplug the AC adapter from the product and power outlet when not using for a long period of time.
12 A • TV/VIDEO , CH ( )/( ) , VOL (–)/(+) , and MENU on the main unit have the same functions as the same buttons on the remote control. Basically, this operation manual provides a description based on operation with the remote control.
13 DISPLA Y AND CONTR OL O VER VIEW (Continued) S-VIDEO P R AUDIO (L) P B VIDEO AUDIO (R) AUDIO (L) COMPONENT AUDIO (L) AUDIO (R) VIDEO Y AV-IN1 Carrying handle Terminals AUDIO (R) S-VIDEO ANT. (Antenna terminal) POWER INPUT (DC12V) AV-IN2/OUT AV-OUT Hold the carrying handle and tilt the screen while steadying the stand with your other hand.
14 CH VOL POWER ENTER BRIGHT MUTE SLEEP PIC. FLIP AUDIO ONLY CC TV/VIDEO FLASH- BACK DISPLAY MENU REMO TE CONTROL 1 PO WER (p. 21) Switch the Liquid Cr ystal T ele vision power on or off . 2 SLEEP (p. 26) Set the sleep timer . 3 ENTER Ex ecute a command.
15 EZ SETUP (WITH A UT O CLOCK SETTING) Control section of main unit S ELECT LA N G U A G E EN GL I SH E S P A ÑO L FRANCA I S SE L EC T : E N T E R: E XIT: ENTER MENU EZ SETUP during the First Power On CH VOL POWER ENTER BRIGHT MUTE SLEEP PIC.
16 EZ SETUP during the First Power On (Continued) EZ SETUP (WITH A UT O CLOCK SETTING) (Continued) START EZ SE TU P? CONN E C T A N T E NNA O R C A B L E .
17 AUTO CLOCK Setting M EN U SL E E P T I M ER PRE S E T CLOSED CAPT I ON V – CH I P BLO CK SE T U P SE L EC T : E XIT: AV AD J U S T ENTER : ENTER MENU BLUE SC RE EN [ OF F ] LANG UAGE SE L EC T : .
18 AUTO CLOCK Setting (Continued) SETTING THE CLOCK (Continued) 5 Press a / b to move the cursor to EDS CH SET, and press ENTER . 6 Press c / d to select AUTO or MANUAL.
19 MANUAL CLOCK Setting M EN U SL E E P T I M ER PRE S E T CLOSED CAPT I ON V –CH I P BLOC K SE T U P AV AD J U S T CLO CK AUTO C LOCK M ANUA L C L O C K OF F SE L EC T : E N T E R: E XIT: RE TUR N .
20 B ASIC OPERA TION Country TV broadcasting Factory setting of color system User setting system TV Video TV U.S.A. Color: NTSC NTSC (N358) World Multi TV ch: US ch US ch Auto System Not required or N.
21 B ASIC OPERA TION (Continued) Control section of main unit 1 Press MAIN POWER , located on the upper side of the main unit, to on. 2 The POWER indicator instantane- ously changes from red to green and the main unit turns on.
22 AV 2 C O MP O N E N T 12 AV 1 STER EO < ON A I R SAP M ONO Switching TV/VIDEO [AV1/AV2/COMPONENT/TV] Modes AV1 mode AV2 mode TV mode 1 Turn on the power of the con- nected video equipment. 2 Press TV/VIDEO and select the applicable input source.
23 Sound Volume CH VOL POWER ENTER BRIGHT MUTE SLEEP PIC. FLIP AUDIO ONLY CC TV/VIDEO FLASH- BACK DISPLAY MENU To mute the sound B ASIC OPERA TION (Continued) 1 Press VOL (+) to increase the sound volume. The bar indicator shifts right. 2 Press VOL (–) to decrease the sound volume.
24 1 Press the button. 2 Press the 5 button. B ASIC OPERA TION (Continued) Changing Channels Changing channels by using Channel Select on the remote control. To select a 1- or 2-digit channel number (e.g., Channel 5): Complete the following procedure within 4 seconds.
25 M EN U SL E E P T I M ER PRE S E T CLOSED CAPT I ON V – CH I P BLO CK SE T U P SE L EC T : E XIT: AV AD J U S T ENTER : ENTER MENU E XIT : PRE S E T ENTER : ENTER SEL E C T : MENU BR I G H TNE SS.
26 Directly setting the SLEEP TIMER 1 Press SLEEP to display the SLEEP TIMER screen. 2 Press SLEEP to set the sleep timer (in minutes). The SLEEP TIMER is turned off when --- is displayed.
27 ADJUSTMENTS (Continued) Adjusting BRIGHTNESS Settings You can adjust the brightness of the screen. Directly setting the BRIGHTNESS 1 Press BRIGHT to display the BRIGHTNESS screen. 2 Press BRIGHT to change the setting. CH VOL POWER ENTER BRIGHT MUTE SLEEP PIC.
28 ADJUSTMENTS (Continued) Adjusting PICTURE FLIP Settings You can set the orientation of the picture. Directly setting the PICTURE FLIP 1 Press PIC. FLIP to display the PICTURE FLIP screen. 2 Press PIC. FLIP to change the setting. CH VOL POWER ENTER BRIGHT MUTE SLEEP PIC.
29 ADJUSTMENTS (Continued) Adjusting AUDIO ONLY Settings When listening to music from a music program, you can set the Liquid Crystal display off and enjoy audio only.
30 1 Press MENU to display the MENU screen. ADJUSTMENTS (Continued) Adjusting PRESET Settings ABC 2 Press a / b to move the cursor to PRESET, and press ENTER . 3 Press a / b to move the cursor to the desired item, and press ENTER . 4 Press c / d to change the setting, and press ENTER .
31 Adjusting LANGUAGE Settings ADJUSTMENTS (Continued) CH VOL POWER ENTER BRIGHT MUTE SLEEP PIC. FLIP AUDIO ONLY CC TV/VIDEO FLASH- BACK DISPLAY MENU ENTER/ a / b M EN U SL E E P T I M ER PRE S E T CL.
32 ADJUSTMENTS (Continued) Adjusting VIDEO ADJUST Settings 1 Press MENU to display the MENU screen. 2 Press a / b to move the cursor to AV ADJUST, and press ENTER .
33 ADJUSTMENTS (Continued) TV mode AV/COMPONENT mode Adjusting VIDEO ADJUST Settings (Continued) N358 P AL-M P AL-N Selected item Press c Press d PICTURE Decrease contrast Increase contrast TINT Towar.
34 ADJUSTMENTS (Continued) Adjusting AUDIO ADJUST Settings 1 Press MENU to display the MENU screen. 2 Press a / b to move the cursor to AV ADJUST, and press ENTER . 3 Press a / b to move the cursor to AUDIO ADJUST, and press ENTER . 4 Press a / b to move the cursor to the desired item, and press ENTER .
35 ADJUSTMENTS (Continued) SET UP ■ EZ SETUP When you move to an area with different broadcasting signals the set will automatically memorize the channel number and time by executing EZ SETUP again. Follow steps 1-3 below, select EZ SETUP, and then go to step 3 on page 15.
36 SET UP (Continued) ■ Saving broadcast TV channels in the memory 1 Press MENU to display the MENU screen, press a / b to move the cursor to SET UP, and press ENTER . 2 Press a / b to move the cursor to CH-SETTING, and press ENTER . 3 Press a / b to move the cursor to CH SEARCH, and press ENTER .
37 ADJUSTMENTS (Continued) ■ BLUE SCREEN Automatically turns the screen blue if no broadcast signal is received. 1 Press MENU to display the MENU screen. 2 Press a / b to move the cursor to SET UP, and press ENTER . Adjusting BLUE SCREEN Settings 3 Press a / b to move the cursor to BLUE SCREEN, and press ENTER .
38 ADJUSTMENTS (Continued) Adjusting CLOSED CAPTION Settings A • If a broadcast contains Closed Caption data and MUTE is pressed, the set enters CAPTION mode automatically. Pressing MUTE again will return the set to its previous condition. • Closed Caption may malfunction (white blocks, strange characters, etc.
39 Adjusting CLOSED CAPTION Settings (Continued) ■ SETTING CLOSED CAPTION ADJUSTMENTS (Continued) 1 Press MENU to display the MENU screen. 2 Press a / b to move the cursor to CLOSED CAPTION, and press ENTER . 3 Press ENTER to change the CLOSED CAPTION setting.
40 Adjusting V-CHIP Settings ■ V-CHIP • This function allows TV programs to be restricted and TV usage to be controlled based on FCC data. It prevents children from watching violent or sexual scenes that may be harmful.
41 ⇐ content based ⇒ FV V S L D (F antasy (Violence) (Se xual (Adult (Sexually Violence) Situation) Language) Suggestive Dialog) TV -Y (All children) TV -Y7 (Direct to Older Children) ✕ TV -G (G.
42 [1] MPAA RATING ■ SETTING V-CHIP Adjusting V-CHIP Settings (Continued) 2 Press a / b to move the cursor to V-CHIP BLOCK, and press ENTER . 4 Press a / b to move the cursor to MPAA, and press ENTER . 5 Press a / b to move the cursor to PG, and press ENTER .
43 [2] TV GUIDELINES ● Setting TV GUIDELINES P arent Control (V -CHIP Operation Continued) Adjusting V-CHIP Settings (Continued) 1 Repeat steps 1 to 3 of [1] MPAA RATING . (See page 42.) 2 Press a / b to move the cursor to TV GUIDELINES, and press ENTER .
44 2 Press a / b to move the cursor to TV GUIDELINES, and press ENTER . 3 Press a / b to move the cursor to BLOCK CONTENT, and press ENTER . 4 Press a / b to move the cursor to the desired item, and press ENTER . A • If you set TV-14 to BLOCK, TV-MA is automatically blocked.
45 [3] A CTIV A TING V -CHIP BLOCK ● Setting ST A TUS Adjusting V-CHIP Settings (Continued) 1 Repeat steps 1 to 3 of [1] MPAA RATING . (See page 42.) 2 Press a / b to move the cursor to STATUS, and press ENTER . 3 Press c / d to set STATUS to ON, and press ENTER .
46 [5] CHANGING V-CHIP BLOCK SETTINGS Adjusting V-CHIP Settings (Continued) 1 Repeat steps 1 to 2 of [1] MPAA RATING , then INPUT SECRET NO. will be displayed. 2 Input the 4-digit secret number by using Channel Select ; the V- CHIP select mode will be dis- played.
47 CONNECTING EXTERNAL DEVICES You can enjoy picture and sound by connecting a VCR or a home video game system to the terminals located on the rear of the TV set. When connecting an external device, turn off the power of the main unit first to prevent any possible damage.
48 CONNECTING EXTERNAL DEVICES (Continued) Connecting a VCR, DVD player or a video camera (AV-IN1/2/COMPONENT) A • If your VCR (or other external devices) has an S-video terminal, S-VIDEO connection is recommended.
49 CONNECTING EXTERNAL DEVICES (Continued) Outputting video and audio (video output) You can output video and audio signals from the TV set through the AV output terminals (AV-OUT). • When using AV2 as an output terminal, select PRESET in the MENU and set AV2 IN/OUT to OUT.
50 TR OUBLESHOO TING ■ Before calling for repair services, make the following checks for possible remedies to the encountered symptoms. TV set Problem Check item Reference Pages There is no picture. There is no picture from AV-IN1/2. 11 – 22 21 Sound Picture • Make sure the AC adapter is properly inserted in the power outlet.
51 Antenna Problem Check item • The reception may be weak. • The quality of the broadcast may also be bad. • Make sure the antenna is facing the right direction. • Make sure the outside antenna is connected. The picture is not sharp. TR OUBLESHOO TING (Continued) The picture moves.
52 SPECIFICA TIONS Items LCD panel Number of dots 921,600 dots VGA Video color systems N358, N443, PAL, PAL-M, PAL-N, SECAM, PAL-60 TV Standard (CCIR) NTSC/PAL-M/PAL-N TV function TV Tuning System PLL 181 ch.
53 DIMENSIONAL DRA WINGS Unit: inch (mm) ■ LC-13S2U 12 23 / 32 (323) 10 33 / 64 (267) 11 17 / 32 (293) 6 41 / 64 (168.7) 7 29 / 32 (200.8) 17 / 64 (7) 3 13 / 16 (97) 2 21 / 64 (59) 1 1 / 2 (38) 8 1 .
54 DIMENSIONAL DRA WINGS (Contin ued) ■ LC-15S2U Unit: inch (mm) 8 1 / 16 (205) 9 1 / 8 (232) 14 19 / 64 (363) 12 5 / 64 (307) 12 3 / 4 (324) 7 7 / 32 (183.
55 DIMENSIONAL DRA WINGS (Contin ued) 4 3 / 64 (103) 5 5 / 32 (131) 8 21 / 32 (220) 2 43 / 64 (68) 7 3 / 16 (182.5) 18 5 / 8 (473) 18 21 / 32 (474) 15 7 / 8 (403.
56 SHARP ELECTRONICS CORPORA TION Shar p Plaza, Mahwah, Ne w Jersey 07430-2135 SHARP CORPORA TION LIMITED W ARRANTY CONSUMER LIMITED W ARRANTY SHARP ELECTRONICS CORPORA TION w arrants to the first con.
57 LIMITED W ARRANTY Consumer Electronics Products Congratulations on y our purchase! Sharp Electronics of Canada Ltd. (hereinafter called “ Sharp ” ) gives the following express warranty to the f.
Ein wichtiger Punkt beim Kauf des Geräts Sharp LC-13S2U, LC-15S2U, LC-20S2U (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sharp LC-13S2U, LC-15S2U, LC-20S2U noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sharp LC-13S2U, LC-15S2U, LC-20S2U - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sharp LC-13S2U, LC-15S2U, LC-20S2U reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sharp LC-13S2U, LC-15S2U, LC-20S2U erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sharp LC-13S2U, LC-15S2U, LC-20S2U besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sharp LC-13S2U, LC-15S2U, LC-20S2U verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sharp LC-13S2U, LC-15S2U, LC-20S2U. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sharp LC-13S2U, LC-15S2U, LC-20S2U gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
