Benutzeranleitung / Produktwartung AR-164 des Produzenten Sharp
Zur Seite of 80
• GETTING STARTED • MAKING COPIES • SPECIAL FEATURES • STATUS INDICATORS • GENERAL INFORMATION • OPTIONAL EQUIPMENT 2 13 28 38 46 65 DIGITAL LASER COPIER/PRINTER OPERATION MANUAL MODEL AR-.
FOR YOUR RECORDS ... To protect against loss or theft, record and retain for reference the copier’s serial number located on the back of the unit. Model Number Serial Number Date of Purchase Place of Purchase Authorized Sharp Copier Service Department Number CA UTIONS Follow the cautions below when using this copier.
1 GETTING ST ARTED SPECIAL FEA TURES MAKING COPIES GENERAL INFORMA TION OPTIONAL EQUIPMENT CONTENTS Page GETTING ST AR TED ● INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ● MAIN FEATURES . . . . . . . . . . . . .
2 GETTING ST ARTED INTR ODUCTION This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all copier features, be sure to familiarize yourself with this manual and the copier.
GETTING ST ARTED GETTING ST ARTED 3 GETTING ST ARTED Main features MAIN FEA TURES High-speed laser copying ● First-copy time is only 7.2 seconds (e xcept in a power sav e mode or immediately after power on). ● Copying speed is 16 copies/min., which adapts to b usiness use, allo wing improvement of w orking eff iciency .
4 GETTING ST ARTED P AR T NAMES AND FUNCTIONS Overall layout Document feeder cover Open to make copies from the original table. Original table All originals which cannot be copied from the SPF must be copied here. Handles Use to move the copier. Power switch Press to turn copier power on and off.
GETTING ST ARTED GETTING ST ARTED 5 GETTING ST ARTED P ART NAMES AND FUNCTIONS Document feeder tray Holds up to 30 originals. Original guides Adjust to the size of the originals. Feeding roller cover Open to remove misfed originals. Exit area Finished originals are output here.
6 GETTING ST ARTED Operation panel P ART NAMES AND FUNCTIONS INTERRUPT key and indicator (p. 25) Interrupts a copy run. Copy quantity display Displays the specified copy quantity during the ready condition and displays the copy countdown as copies are made.
GETTING ST ARTED GETTING ST ARTED 7 GETTING ST ARTED P ART NAMES AND FUNCTIONS Press and hold down the ke y . 12,345 sheets output 1st display 2nd display Note: 11" x 17" size copies are counted as two copies. CLEAR key Clears the copy quantity display or terminates a copy run.
8 GETTING ST ARTED Copier installation COPIER INST ALLA TION Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is mov ed from a cool place to a war m place, condensation ma y f or m inside the copier .
GETTING ST ARTED GETTING ST ARTED 9 GETTING ST ARTED CA UTIONS ON HANDLING Be careful in handling the copier as follows to maintain the performance of this copier. Do not drop the copier, subject it to shock or strike it against any object. Store spare toner cartridges in a cool dry place without removing from the package before use.
10 GETTING ST ARTED LO ADING COPY P APER To save space, this copier has been designed with an adjustable front-loading tray, which is easily opened for paper loading.
GETTING ST ARTED GETTING ST ARTED 11 GETTING ST ARTED Changing the copy paper size in the tra y 1 Gently lift and pull out the paper tray until it stops. 2 Push the pressure plate down until it locks in place. 3 Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper.
12 GETTING ST ARTED Loading copy paper LO ADING COPY P APER 8 To set the selected paper size, press the PAPER SIZE ENTER key. ● The selected paper feed location indicator will blink and the corresponding paper size (which is currently set) indicator will light up steadily.
13 MAKING COPIES A UDITING A CCOUNTS If this copier has been programmed in the auditing mode, it will not function until an assigned 3-digit account number has been entered.
14 MAKING COPIES NORMAL COPYING Using the SPF Stream feeding mode If the stream feeding mode has been enabled using user program No. 4, the SPF indicator will continue to blink for approximately 5 seconds after feeding of all originals is completed.
15 MAKING COPIES NORMAL COPYING Normal copying 6 Adjust the copy density. ● This copier has three exposure modes to choose from — AUTOMATIC, MANUAL, and PHOTO.
16 MAKING COPIES 1 Turn the power switch on. ● It will take about 35 seconds for the copier to warm up. However, you can make desired settings and press the START key during warm-up.
17 MAKING COPIES ● For manual copy density adjustment, press the AUTO/MANUAL/ PHOTO key to select MANUAL and adjust with the light ( ) and dark ( ) keys as desired. ● For photographs, select PHOTO and then adjust with the light ( ) and dark ( ) keys as desired.
18 MAKING COPIES REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or manually with the PRESET RATIO selector ( , ) keys and/or the zoom ( , ) keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments.
19 MAKING COPIES REDUCTION/ENLARGEMENT/ZOOM Reduction/enlargement/zoom Manual 1 Place the original in the document feeder tray or on the original table. 2 Use the PRESET RATIO selector ( , ) keys and the zoom ( , ) keys to select the desired copy ratio.
20 MAKING COPIES BYP ASS FEED (special paper) The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray. 1 Unfold the bypass tray. ● When feeding 8-1/2" x 14" or 11" x 17" sized paper, extend the feeder tray.
21 MAKING COPIES 4 Press the TRAY SELECT key to select the bypass tray. 5 Leave the copy quantity at 0 if using special papers. Set the number of copies if using standard copy paper or envelopes.
22 MAKING COPIES TW O-SIDED COPYING Two-sided copies can be made on this copier using the bypass tray. 1 Place the first original on the original table and make a copy. ● The first copy can be made using any of the paper feed stations. 2 Replace the first original with the second original and close the platen cover.
23 MAKING COPIES SOR T/GR OUP This copier has two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of the originals and the second groups copies by originals. The sort/group feature cannot be used with the dual page copy feature.
24 MAKING COPIES Sort/group SORT/GR OUP Copying in the sort mode When copying in the sort mode, the original image will be stored in the copier memory each time an original is scanned and copying will start after all originals have been scanned. 1 Set the originals face up in the document feeder tray.
25 MAKING COPIES 1 Press the INTERRUPT key. ● The copier will return to the initial settings. ● If this copier has been programmed in the auditing mode using user program No. 10, “ ––– ” will appear in the copy quantity display. Enter your account number using the numeric keys.
26 MAKING COPIES 1 Press the AUTO/MANUAL/PHOTO key to select the PHOTO mode. 2 Press and hold down the AUTO/MANUAL/PHOTO key for approximately 5 seconds. ● The PHOTO indicator will go out and the AUTO indicator will begin to blink. ● One or two exposure indicators corresponding to the current auto- matic exposure level will light up.
27 MAKING COPIES Toner save mode 1 Press the AUTO/MANUAL/PHOTO key to select the MANUAL mode. 2 Press and hold down the AUTO/MANUAL/PHOTO key for approximately 5 seconds. ● The MANUAL indicator will go out and the PHOTO indicator will begin to blink.
28 SPECIAL FEATURES 1 Place the original in the document feeder tray or on the original table. 2 Press the XY-ZOOM key. ● The current value for the vertical direction will be displayed in the copy quantity display. 3 Use the PRESET RATIO selector ( , ) keys and zoom ( , ) keys to change the copy ratio in the vertical direction.
29 SPECIAL FEA TURES XY zoom XY ZOOM 5 Use the PRESET RATIO selector ( , ) keys and zoom ( , ) keys to change the copy ratio in the horizontal direction in a similar manner as for the vertical direction.
30 SPECIAL FEATURES B/W REVERSE The B/W REVERSE feature is used to reverse black and white areas. ● When the B/W REVERSE feature is selected, the exposure mode will be automatically set to the MANUAL mode. Other exposure modes cannot be selected. Even if this feature is canceled, the MANUAL mode will not automatically be canceled.
31 SPECIAL FEA TURES 1 Place the originals on the original table with the center of the two pages aligned with the paper size index ( 8 1 / 2 ). Close the platen cover. ● Set the page to be copied first to the right of the paper size index mark. 2 Press the DUAL PAGE COPY key.
32 SPECIAL FEATURES R O T A TION COPYING If user program No. 7 is set, the image of the original will rotate when the orientation of the original does not match that of the copy paper. Rotation copying will function only if the AUTO PAPER SELECT mode or AUTO IMAGE mode has been selected.
33 SPECIAL FEA TURES 1 Set the originals face up in the document feeder tray. ● The original table cannot be used for the 2 in 1 or 4 in 1 feature. 2 Use the TRAY SELECT key to select the paper tray with the desired paper size. ● The bypass tray and any tray with non-standard size paper cannot be used with the 2 in 1 or 4 in 1 feature.
34 SPECIAL FEATURES 2 in 1 or 4 in 1 4 Enter the desired pattern number using a numeric key. ● The entered number will blink in the copy quantity display. For layout pattern numbers, see the previous page. 5 Press the START key. ● The entered number will light up steadily.
35 SPECIAL FEA TURES 1 Place the original on the original table and close the platen cover. ● The SPF can also be used for this feature. 2 Press the ERASE key to select the desired erase mode. ● To select the EDGE + CENTER ERASE mode, press the ERASE key until both the EDGE and CENTER indicators light up.
36 SPECIAL FEATURES 4 Set the number of copies. 5 Press the START key. Erase ERASE.
37 SPECIAL FEA TURES Margin shift MARGIN SHIFT The MARGIN SHIFT feature automatically shifts the text or image to the right to increase the left margin by approximately 1/4". ● This feature cannot be used with the 2 in 1 or 4 in 1 feature. 1 Place the original in the document feeder tray or on the original table.
38 ST A TUS INDICA T ORS 1 Open the bypass tray. Lift slightly on the side cover and slide the cover out until it stops. 2 Push gently on both sides of the front cover and open it. 3 Push the toner cartridge lock release lever and pull the toner cartridge out.
39 ST A TUS INDICA T ORS Toner cartridge replacement T ONER CAR TRIDGE REPLA CEMENT 5 Gently insert the toner cartridge along the guides until it locks in place while pushing the lock release lever. If dirt or dust is adhered to the toner cartridge, remove it before installing the cartridge.
40 ST A TUS INDICA T ORS The copier will stop when a misfeed occurs. The misfeed ( ) indicator will blink, and blinking red misfeed location indicators will indicate the approximate misfeed location. If paper is accidentally torn during removal, be sure to remove all pieces.
41 ST A TUS INDICA T ORS Misfeed removal MISFEED REMO V AL Roller 3 If the misfed original cannot be removed in steps 1 and 2, remove the misfed original from the exit area. Open the document feeder cover and rotate the roller in the direction indicated by the arrow if needed.
42 ST A TUS INDICA T ORS MISFEED REMO V AL Misfeed removal If the misfed paper is seen from this side, proceed to “ C. Misfeed in the transport area ” . If paper is misfed here, proceed to “ B. Misfeed in the fusing area ” . If paper is misfed here, proceed to “ A.
43 ST A TUS INDICA T ORS MISFEED REMO V AL Misfeed removal Roller rotating knob Fusing unit release le vers 2 Turn the roller rotating knob in the direction of the arrow. 3 Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal.
44 ST A TUS INDICA T ORS MISFEED REMO V AL Misfeed removal 3 Close the side cover by pressing the handle on the cover. ● The misfeed ( ) indicator will go out.
45 ST A TUS INDICA T ORS Developer required/ Maintenance required MAINTENANCE REQUIRED When the indicator lights up, service by an authorized SHARP service technician is required. Contact your service center as soon as possible. When the indicator lights up, the developer should be replaced.
46 GENERAL INFORMA TION User programs USER PR OGRAMS The user programs allow the parameters of certain functions to be set, changed, or canceled as desired. List of user pr ograms This copier has the following user programs. Program No. Program name Description 1 Auto clear time Sets the auto clear time.
47 GENERAL INFORMA TION Setting the user programs 1 Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and “– –” appears in the copy quantity display. 2 Enter a program number using the numeric keys.
48 GENERAL INFORMA TION USER PR OGRAMS 4 Select the desired parameter using the numeric keys. ● The entered parameter number will blink on the right side of the copy quantity display. ● The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min.
49 GENERAL INFORMA TION USER PR OGRAMS User programs Settings f or auditing accounts Setting of user programs No. 10 to 15 varies with the program number. For settings of all programs, first follow steps 1 to 3 in “ Setting the user programs ” on page 47 to select a program.
50 GENERAL INFORMA TION USER PR OGRAMS User programs Pr ogram No. 12: Account n umber change Program No. 12 is used to change account numbers. When program No. 12 is entered, an account number will appear in the copy quantity display. ● If no account number has been registered, “ 12E ” will appear in the copy quantity display.
51 GENERAL INFORMA TION User programs USER PR OGRAMS Pr ogram No. 14: Number of copies per account Program No. 14 is used to display the total number of copies made against each account number. When program No. 14 is entered, an account number will appear in the copy quantity display.
52 GENERAL INFORMA TION USER PR OGRAMS User programs Pr ogram No. 15: Resetting account Program No. 15 is used to reset all accounts or to reset any desired individual account. When program No. 15 is entered, “ 0 ” will blink on the right side of the copy quantity display.
53 GENERAL INFORMA TION PO WER SA VE MODES The copier has two power save modes to reduce overall power consumption thereby reduce the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode.
54 GENERAL INFORMA TION Setting the power sa ve modes The time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No. 2 for the preheat mode and user program No. 3 for the auto power shut-off mode.
55 GENERAL INFORMA TION USER MAINTENANCE Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Original table and platen co ver Stains or dirt on the original table or platen cover will also be copied.
56 GENERAL INFORMA TION T ransfer char ger cleaning If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. 1 Turn the power switch off. 2 Open the bypass tray. Lift slightly on the side cover and slide the cover out until it stops.
57 GENERAL INFORMA TION Problem Solution ● Copier plugged in? ● Power switch ON? ● Copy density properly adjusted? ● Is the original placed face up in the SPF or face down on the original tabl.
58 GENERAL INFORMA TION Problem Solution Copier trouble? COPIER TR OUBLE? COPY/FAX key The COPY/FAX key is used to switch between the FAX and COPY modes.
59 GENERAL INFORMA TION Copier trouble? Self-diagnostic function An automatic self-diagnostic function is built into the copier. Should the copier malfunction, the self-diagnostic function will locate the problem and stop the copier to prevent damage.
60 GENERAL INFORMA TION SUPPLIES T ypes and sizes of copy paper Size Weight Capacity Special paper (21 lb. bond paper) Paper tray 5-1/2" x 8-1/2"* 15 lbs. to 21 lbs. 250 sheets to 11" x 17" Bypass tray Ordinary paper: 15 lbs. to 34 lbs.
61 GENERAL INFORMA TION SUPPLIES Genuine supplies statement Standard supplies for this copier that are to be replaced by the user are copy paper and toner cartridge. For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered and tested to maximize the life and performance of SHARP copiers.
62 GENERAL INFORMA TION Type Desktop Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. 11" x 17" Copy sizes Max. 11" x 17" Min. 5-1/2" x 8-1/2" Image loss: Max. 5/32" (4 mm) (leading and trailing edges) Max.
63 GENERAL INFORMA TION SPECIFICA TIONS Specifications Overall dimensions 23-15/64" (W) x 20-29/32" (D) (with bypass tray folded) (590 mm (W) x 531 mm (D)) Weight Approx.
64 GENERAL INFORMA TION MEMO.
65 OPTIONAL EQUIPMENT OPTIONAL EQ UIPMENT CONTENTS Page ● SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 ● 250-SHEET PAPER FEED UNIT (AR-DE5)/ 2x250-SHEET PAPER FEED UNIT (AR-DE6) . . . . . . . . . . . . . . 67 ● Loading copy paper .
66 OPTIONAL EQUIPMENT SYSTEM CONFIGURA TION A number of options are available for the copier which allow you to configure a copier system to meet your particular needs.
67 OPTIONAL EQUIPMENT Loading cop y paper The method of loading copy paper for the paper trays of these paper feed units is the same as for the paper tray in the copier. See page 10. The method of changing the copy paper size is also the same for the paper tray in the copier.
68 OPTIONAL EQUIPMENT Misfeed remo val The copier will stop when a misfeed occurs. The misfeed ( ) indicator and the red indicator which indicates the paper feed unit will blink. 1 Open the side cover of the paper feed unit and remove the misfed paper.
69 OPTIONAL EQUIPMENT Specifications Copy paper size 8-1/2" x 11" to 11" x 17" Paper weight 15 lbs. to 21 lbs. Paper capacity One paper tray with capacity for 250 sheets of 21 lb.
70 2 250-sheet paper feed unit . . . . . . . . . . . . . . . . . . . . . . . 67 2 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 2x250-sheet paper feed unit . . . . . . . . . . . . . . . . . . . . . 67 4 4 in 1 .
71 R Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Replacement – toner cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 S Single pass feeder (SPF) . . . . . . . . . . . . . . . . . . . . .
72 Date Issued: No v . 1, 2000 MA TERIAL SAFETY D A T A SHEET MSDS No . F-00991 Section 1. Product Identification Product: AR-201NT/T/FT/ST (Black Toner) Section 2. Supplier ’ s Name and Address Shar p Cor poration 22-22 Nagaike-cho , Abeno-ku, Osaka, Japan Local suppliers are listed below .
73 Section 6. Physical Chemical Characteristics Boiling / Melting P oint: Not applicable Specific Gra vity: 1.1 V apor Pressure: Not applicable Solubility in Water: Negligible V apor Density: Not applicable PH: Not applicab le Ev aporation Rate: Not applicab le Viscosity: Not applicable Appearance: Fine powder Color: Black Odor: Odorless Section 7.
74 Date Issued: No v . 1, 2000 MA TERIAL SAFETY D A T A SHEET MSDS No . F-30991 Section 1. Product Identification Product AR-201ND/DV/SD (Black Developer) Section 2. Supplier ’ s Name and Address Shar p Cor poration 22-22 Nagaike-cho , Abeno-ku, Osaka, Japan Local suppliers are listed below .
75 Section 6. Physical Chemical Characteristics Boiling / Melting P oint: Not applicable Specific Gra vity: about 7.3 V apor Pressure: Not applicable Solubility in Water: Negligible V apor Density: No.
MEMO.
W ARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not e xpressly approved b y the manuf acturer could v oid the user's authority to operate this equipment.
PRINTED IN CHINA 2002B KS TINSE0000QSZZ AR-164 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135. SHARP CORPORATION www .shar p-usa.
Ein wichtiger Punkt beim Kauf des Geräts Sharp AR-164 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sharp AR-164 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sharp AR-164 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sharp AR-164 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sharp AR-164 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sharp AR-164 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sharp AR-164 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sharp AR-164. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sharp AR-164 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
