Benutzeranleitung / Produktwartung ADC732 des Produzenten Sensormatic
Zur Seite of 52
S E RVICE MANU AL RT330C3/RT330C3-1/ADC732/ADC732X RT470C3/RT470C3-1/ADC762/ADC762X COLOR VIDEO CAMERA No. 6690SEN Aug. 2000 COPYRIGHT © 2000 VICTOR COMPANY OF JAPAN, LTD.
Section T itle Page Section T itle Page T ABLE OF CONTENTS INSTRUCTIONS 1. DISASSEMBL Y 1.1 REPLACING THE FUSE ............................................. 1-1 1.2 REMOV AL OF CIRCUIT BOARDS ............................. 1-1 1.3 REPLACING THE CCD IMAGE SENSOR .
1-1 SECTION 1 DISASSEMBL Y Fig. 1-1 Fig. 1-2-2 Fig. 1-2-4 Fig. 1-2-1 1.1 REPLA CING THE FUSE CAUTION Before replacing the fuse, check the cause of the fuse blow in order to prevent a recurrence of the problem, repair and confirm its normal operation.
1-2 (6) T urn over the main unit, remove the two screws 4 , and then detach the heat sink Ç and the chassis Î . (7) In order to remove the EE board, bring it down, level it and then pull it out in the direction of the arrow mark.
1-3 Note: Before installation, take notes of the code of the CCD im- age sensor . It needs to refer to this code for adjustment. 1st. pin Index V RGL code V SUB code ICX0***K- A Fig. 1-3-2 1.4 SER VICING OF CIRCUIT BO ARDS (1) As a consequence of 1.2, disassemble the board as shown in fig.
2-1 SECTION 2 ELECTRICAL ADJUSTMENTS T o change the setting of adjustment items, use a computer with the adjustment software to change the set value of the EVR for each adjustment item as well as to store the changed data into the memory of the camera.
2-2 2.1.3 Required system for adjustments 2.1.4 Required instruments for adjustment Note: Equipments marked with asterisk are not handled by parts department. Equipments Specifications Computer 486DX4/100MHz or higher micro processor (Recommended Pentium Processor) Operating system Windows 95 or Windows 98 Memory 16M Byte or more FDD 3.
2-3 2.2 ST ANDARD SETUP 2.3 SWITCH SETTING FOR ADJUSTMENT RB DC12V AC24V 2 1 VIDEO OUT SEE INSTRUCTION MANUAL POWER RESET OFF OFF OFF AUTO LL PHASE WHT.
2-4 2.4.3 What is “Initial Data” The initial data loaded at “ 2.5 INITIALIZE ” consists of preset adjustment values. Therefore, once the adjustment procedure is started, all adjustment should be done from beginning to the end. Otherwise, the preset adjustment values would be written as the adjustment data.
2-5 Item Mode Adjustment procedure Measuring instrument & Input signals No. Measuring point ( * ) Adjustment parts ( - ) Adjustment level ( + ) 2.5 INITIALIZE 1) Select either “ TK-C700U.cor ” for RT330C3, ADC732 or “ TK-C700E.cor ” for RT330C3-1, ADC732X to on Scenario file define adjust- ment.
2-6 Item Mode Adjustment procedure Measuring instrument & Input signals No. Measuring point ( * ) Adjustment parts ( - ) Adjustment level ( + ) 2.7 ADJUSTMENT OF CCD 1) Select the “ NEXT ” button to display “ V SUB voltage ” on the title bar .
2-7 Item Mode Adjustment procedure Measuring instrument & Input signals No. Measuring point ( * ) Adjustment parts ( - ) Adjustment level ( + ) 2.8 ADJUSTMENT OF VIDEO SIGNAL 1 White clip adjustme.
2-8 Item Mode Adjustment procedure Measuring instrument & Input signals No. Measuring point ( * ) Adjustment parts ( - ) Adjustment level ( + ) 3 Setup level adjustment Oscilloscope (H-rate: 10:1) or W .F .M. 1) Select the “ NEXT ” button to display “ Setup level ” on the title bar .
2-9 Item Mode Adjustment procedure Measuring instrument & Input signals No. Measuring point ( * ) Adjustment parts ( - ) Adjustment level ( + ) 2.9 ADJUSTMENT OF WHITE BALANCE 1 White balance adjustment(1) * VIDEO OUT (75 ohm T ermination) - LENS IRIS 1) Select the “ NEXT ” button to display “ White balance (1) ” on the title bar .
2-10 Item Mode Adjustment procedure Measuring instrument & Input signals No. Measuring point ( * ) Adjustment parts ( - ) Adjustment level ( + ) 3 White balance adjustment filter (No. 80D+82A) * VIDEO OUT (75 ohm T ermination) - LENS IRIS 1) Press the “ NEXT ” button.
2-11 Item Mode Adjustment procedure Measuring instrument & Input signals No. Measuring point ( * ) Adjustment parts ( - ) Adjustment level ( + ) 5 White balance adjustment (2) filter (No.80B+80B) White balance chart Oscilloscope (H-rate, 10:1) or W .
2-12 Item Mode Adjustment procedure Measuring instrument & Input signals No. Measuring point ( * ) Adjustment parts ( - ) Adjustment level ( + ) 2.10 ADJUSTMENT OF CHROMA SIGNAL 1 Color level and hue adjustment Oscilloscope (H-rote, 10:1) or W .F .
2-13 Focus chart.
SECTION 3 CHAR TS AND DIAGRAMS 䡵 REPLACING SUBMINIA TURE “CHIP” P ARTS • Some resistors, shorting jumpers (0 ohm resistance), ceramic capacitors, transistors, and diodes are chip parts. These chip parts cannot be reused after they are once removed.
VCO 26 DD Amp Sense Pulse Generator Auto Calibration IC203 MODE SWITCHING CENTER BIAS CENTER BIAS LIN CLP COSCLP2 COSCLP1 SH1 1 CAM/VIDEO PBRFC RFCONT 32 31 GND2 LIN/CH N.
3.3 3.4 CCD CIRCUIT BOARD SIDE A FROM/TO PRO CN1 CCD R108 R109 R110 C103 R111 180k 27k 680 1500p OPEN 100k 39k 820 2200p 0 SC93524 -7.9 -0.3 -0.3 4.1 2.9 7.7 2.4 2.7 0 5.2 -8.3 12.6 14.5 7.7 7.0 CCD SCHEMA TIC DIAGRAM ( Page 3-4 ) 1 8 16 9 CCD TP101 -7.
1/2 V DRIVER TIMING DRIVER DRIVER DRIVER DRIVER CHARGE PUMP LATCH MODE SET CDS CDS LPF S&H BLK AGC CLP DAC X8 FINE LATCH COMPARATE ENCODE & LATCH CORRECTION COARSE & COMPARATE & FINE E.
1 2 25 24 8 5 1 4 1 8 16 9 5 8 4 1 1 8 16 9 8 5 1 4 4 1 5 8 5 8 4 1 8 5 1 4 1 2 3 4 5 1 4 25 1 26 100 50 51 75 76 8 1 32 25 9 16 24 17 25 36 37 48 1 12 13 24 1 12 13 24 48 37 36 25 3.6 PRO CIRCUIT BOARD ADDRESS T ABLE OF BO ARD P ARTS Each address may ha ve an address error b y one inter val.
3.7 FROM/TO PRO CN2 SC93523 1.4 2.0 2.0 5.6 1.5 8.1 1.5 0.2 0 5.14 1.3 9.3 0 0.2 1.2 0 2.2 5.6 1.6 0.6 0.6 2.2 0 1.5 2.8 0 3.3 0.6 2.2 0 1.5 3.2 EE SCHEMATIC DIAGRAM FROM/TO TER CN100 ( Page 3-7 ) ( P.
VR500 TB500 8 5 1 4 3.8 EE CIRCUIT BOARD 3.9 3.10 TER CIRCUIT BOARD 54321 A B C SIDE B SIDE B ADDRESS TABLE OF BOARD PARTS Each address may have an address error by one interval.
D501 D503 D500 D540 1 2 11 12 3.11 3.12 POW CIRCUIT BOARD 654321 A B C D SIDE B ADDRESS TABLE OF BOARD PARTS Each address may have an address error by one interval.
3-9 3-9 3.13 BLOCK DIAGRAMS of IC'S 䡵 AK6420AM-X [ASAHIKASEI] (2048 bits (128 Words X 16 bits) EEPROM) 䡵 AN8085M-X [MA TSUSHIT A] (REG Servo) 䡵 BA10358F-XE [ROHM] (Dual Ground Sense Op.
3-10 3-10 䡵 CXD2163AR [SONY] (Digital signal processor for single chip CCD color video camera).
3-11 3-11.
3-12 3-12 䡵 CXD2480R [SONY] (T iming Control with CCD Drivers).
3-13 3-13.
3-14 3-14.
3-15 3-15 䡵 ICX054BK [SONY] (1/3 Inch CCD Image Sensor for NTSC Color Camera).
3-16 3-16 䡵 ICX055BK [SONY] (1/3 Inch CCD Image Sensor for P AL Color Camera).
3-17 3-17.
3-18 3-18 䡵 ICX058CK [SONY] (1/3 Inch CCD Image Sensor for NTSC Color Camera).
3-19 3-19 䡵 ICX059CK [SONY] (1/3 Inch CCD Image Sensor for P AL Color Camera).
3-20 3-20 䡵 MB88347PFV -X [FUJITSU] (D/A Convertor) 䡵 NJM2267V -W [JRC] (Dual 6dB Video Amplifier including 75 Ω Driver) 䡵 NJM2509V -W [JRC] (Super Imposer including Y/C MIX Circuit) 䡵 NJM43.
3-21 3-21 䡵 TC4W53F-X [TOSHIBA] (2-Channel Multiplexer) 䡵 TC74HC08AF-X [TOSHIBA] (Quad 2-Input AND Gates) 䡵 TC7S32FU-X [TOSHIBA] (2 Input Single OR Gate) 䡵 TC7W02F-X [TOSHIBA] (2 Input Dual NOR Gate) 䡵 TK11333BMC-X [TOKO] (Regulator) 䡵 TK11650U-X [TOKO] (3-T erminal Positive V oltage Regulator) 䡵 UPC358G2-WE [NEC] (Dual Op.
25 24 23 27 26 FUSE See Sec1.1 *2 *2 The Ground lug is for R T470C3, RT470C3-1, ADC762, ADC762X only . *1 *2 POW BOARD Q504 EE BOARD 03 PRO BOARD 02 POW BO ARD 05 CCD BOARD 01 1PIN 19 18 28 *1 P erform the FFC cable wiring as shown in the diag ram below .
1 SC32036H-001 CAP 2 SC40286H-001 SHEET 3 SC20733H-001 FRONT FRAME 4 SC46597H-001 COIL SPRING 5 SC20730H-001 SENSOR BASE 6 SC32334H-001 ADJUST RING 7 SC46598-001 LEAF SPRING 8 SC46599H-001 HOLDER PLA TE 9 QAJ0004-001 OP L.P .F RT470C3, R T470C3-1, ADC762, ADC762X 9 QAJ0003-001 OP L.
SECTION 5 ELECTRICAL P ARTS LIST SAFETY PRECAUTION: Parts identified by the ! symbol are criticaI for safety . Replace only with specified parts numbers. For maximum reliability and performance, all other replacement parts should be identical to those specified.
Symbol No. Part No. Part Name Description Symbol No. Part No. Part Name Description Q101 2SC4618(PQ)-X TRANSISTOR ROHM R101 NRSA63J-0R0X M.G.RESISTOR 0 1/16W R102 NRSA63J-0R0X M.G.RESISTOR 0 1/16W R103 NRSA63J-0R0X M.G.RESISTOR 0 1/16W R104 NRSA63J-0R0X M.
Symbol No. Part No. Part Name Description Symbol No. Part No. Part Name Description IC200 NJM79L08UA-X I.C.(M) JRC IC201 NJM78L15UA-X I.C.(M) JRC IC202 CXD2480R I.C.(M) SONY IC203 CXA2006Q I.C.(M) SONY IC204 CXD2312R I.C.(M) SONY IC205 AK6420AM-X I.C.
Symbol No. Part No. Part Name Description Symbol No. Part No. Part Name Description R283 NRSA63J-104X M.G.RESISTOR 100k 1/16W R284 NRSA63J-333X M.G.RESISTOR 33k 1/16W R285 NRSA63J-333X M.G.RESISTOR 33k 1/16W R286 NRSA63J-472X M.G.RESISTOR 4.7k 1/16W R287 NRSA63J-333X M.
Symbol No. Part No. Part Name Description Symbol No. Part No. Part Name Description C284 NEN71HM-224X N.P .CAP ACITOR 0.22 50V C285 NCF31CZ-104X CER.CAP ACITOR 0.1 16V C286 NCF31CZ-104X CER.CAP ACITOR 0.1 16V C287 NCF31CZ-104X CER.CAP ACITOR 0.1 16V C288 NCF31CZ-104X CER.
Symbol No. Part No. Part Name Description Symbol No. Part No. Part Name Description Q221 MSD1819A/R/-X TRANSISTOR MOTOROLA Q222 MSB1218A/R/-X TRANSISTOR MOTOROLA D200 1SS357-X DIODE D201 1SS357-X DIODE D202 1SS357-X DIODE D203 1SS357-X DIODE D204 1SS357-X DIODE D205 HVU306A5-W V .
Symbol No. Part No. Part Name Description Symbol No. Part No. Part Name Description R326 NRSA63J-682X M.G.RESISTOR 6.8k 1/16W R327 NRSA63J-472X M.G.RESISTOR 4.7k 1/16W R328 NRSA63J-333X M.G.RESISTOR 33k 1/16W R329 NRSA63J-103X M.G.RESISTOR 10k 1/16W R330 NRSA63J-821X M.
Symbol No. Part No. Part Name Description Symbol No. Part No. Part Name Description 5-8 R506 NRSA02J-470X M.G.RESISTOR 47 1/10W R507 NRSA02J-273X M.G.RESISTOR 27k 1/10W R508 NRSA02J-223X M.G.RESISTOR 22k 1/10W R509 NRSA02J-823X M.G.RESISTOR 82k 1/10W R510 NRSA02J-223X M.
Symbol No. Part No. Part Name Description Symbol No. Part No. Part Name Description IC530 NJM431U-X I.C.(M) JRC Q500 2SC3311A/RS/-T TRANSISTOR MA TSUSHIT A Q501 2SC3311A/RS/-T TRANSISTOR MA TSUSHIT A .
SECTION 6 P ACKING INSTR UCTIONS • R T330C3, RT330C3-1, R T470C3, R T470C3-1 SC96936H (English, F rench, Spanish) SC96937H (Germany , Italian, Chinese) • ADC732, ADC732X, ADC762, ADC762X SC96965H .
S E RVICE MANU AL RT330C3/RT330C3-1/ADC732/ADC732X RT470C3/RT470C3-1/ADC762/ADC762X COLOR VIDEO CAMERA No. 6690SEN Aug. 2000 COPYRIGHT © 2000 VICTOR COMPANY OF JAPAN, LTD.
Ein wichtiger Punkt beim Kauf des Geräts Sensormatic ADC732 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sensormatic ADC732 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sensormatic ADC732 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sensormatic ADC732 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sensormatic ADC732 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sensormatic ADC732 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sensormatic ADC732 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sensormatic ADC732. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sensormatic ADC732 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
