Benutzeranleitung / Produktwartung HMEC 26-2 des Produzenten Sennheiser
Zur Seite of 32
Instruction manual HMEC 26-2.
Important safety information HMEC 26-2 | 1 Important safety information 왘 Please read this i nstruction manual carefully and completely befo re using the product. 왘 Always include this instruction manual when passing the product on to third pa rties.
Important safety information 2 | HMEC 26-2 NoiseGard TM switched on, you can hear and recognize these sounds. Set the volume to safe levels that do not interfere with your ability to hear informational sounds and warning alarms. 왘 The product is capable of producing sound pressure exceeding 85 dB(A).
Important safety information HMEC 26-2 | 3 Intended use Intended use of the product includes • having read and und erstood this instructio n manual, especially the chapter “Importa n t s a fe ty in fo rm a ti on ” o n page 1, • using the product wi thin the operating conditions and limitations descri bed in this instru ction manual.
The HMEC 26-2 headset 4 | HMEC 26-2 The HMEC 26-2 headset The HMEC 26-2 headset with NoiseGard™ profess ional active noise compensation features dynamic, closed headphones. The noise-compensating cond enser microphone ensures excellent speech transmission even in noisy environments.
Package contents HMEC 26-2 | 5 • With NoiseGard™ switched off, th e headset can be used as a conventional headset • Power supply for NoiseGard™ from aircraf t DC power supply system (on suitab.
Operation 6 | HMEC 26-2 Operation Putting on the headset When putting on the headset, the patented two-piece headband adjusts automatically. Flipping away one earcup The headset features a “flip-away” earcup for single-sided listening.
Operation HMEC 26-2 | 7 Positioning the mi crophone Bend the flexible microphone boom so that the microphone is placed at the corner of the mouth. Maintain a di stance of 2 cm between microphone and mouth. Alw ays use the supplied wind and pop screen.
Operation 8 | HMEC 26-2 Adjusting the volume direct ly on the audio system Connect the headset to the corresponding soc kets of your audio system. Adjust the volu me directly on the audio system. Adjusting the microph one sensitivity T urn a small screwdriver in the direction of the arrow to change the microphone sensitivity.
The control units of the HMEC 26-2 HMEC 26-2 | 9 The control units of the HMEC 26-2 Control unit I 1 Volume controls 2 LED 3 NoiseGard™ ON / OFF switch 4 Mono/stereo switch / 5 BOOM switch L / R 6 3.5 mm jack socket 7 Battery compartment 8 2.
The control units of the HMEC 26-2 10 | HMEC 26-2 Control unit II 2 LED 3 NoiseGard™ ON / OFF switch Headset with control unit II Operating element 12345678 Cable -CP Cable -CP-2 Cable -KP Cable -KP.
Using the headset HMEC 26-2 | 11 Using the headset Switching Nois eGard™ on/off The NoiseGard™ ON / OFF switch 3 allows you to switch the NoiseGard™ active noise comp ensation on or off. With NoiseGard™ switched off, the headset can be used as a conventional headset.
Using the headset 12 | HMEC 26-2 Adjusting the volume The two slide volume controls 1 allow you to adjust the volume for the lef t and right channel separately. Switching between mono and stereo mode The mono/stereo switch 4 allows you to switch between mono ( ) and stereo ( ) mode, depending on the audio system.
Using the headset HMEC 26-2 | 13 Poweri ng Nois eGard™ via tw o (rechargeable) batteries 왘 Insert two 1.5 V AA alk aline batteries (IEC LR 6) or two 1.2 V AA rechargeable batteries (IEC LR 6). Observe correct polarity when in serting the batteries.
Using the headset 14 | HMEC 26-2 왘 Set the switch to the positio n ASO . Switching the T alkThrough function on/off (HMEC 26-2-T only) The headse t provide s excell ent attenuation of ambient noise. In order to allow you to communicate undisturb ed with your surroundings whil e wearing the headset, the HMEC 26-2-T features a TalkThrough function.
Using the headset HMEC 26-2 | 15 Connecting a mobile telephone The 2.5 mm jack socket 8 allows you to connect a mobil e telephone. For this purpose, the NoiseGard™ active noise compensation must be switch ed on and the m icrophone connector must be connected to th e aircraf t radio/audio.
Using the headset 16 | HMEC 26-2 왘 Connect the audio cable to the 2.5 mm jack socket 8 on the control unit I and to the corresponding jac k socket on your mobile telephone. You can adjust the volume of the mobile telephone via the headset’s contro l unit.
Using the headset HMEC 26-2 | 17 왘 Connect the audio cable to the 3.5 mm jack socket 6 on the control unit I and to the corresponding jack socket on your audio player. Attaching the belt clip The belt clip a llows you to atta ch the control un it to the seat belt so th at the cont rol unit d oesn’t hinder yo u.
Using the headset 18 | HMEC 26-2 Attaching the cable clip The cable clip allows you to attach the headphone cable to your clothing so that the cabl e doesn’t hinder or distr act you. 왘 Loop the cable through the cli p so that the headphone cable doesn‘t hinder you.
Care and maintenance HMEC 26-2 | 19 Care and maintenance Cleaning and maintain ing the headset 왘 Before cleaning, pull out the plugs of the p roduct from the connections in the aircraf t. 왘 Only use a sof t , dry cloth to clean the product. Replacing the ear pads For reasons of hygiene, you should re place the ear pads annually.
Care and main tenance 20 | HMEC 26-2 Replacing the headband paddings For reasons of hygiene, you should replace the headband paddings an nually. 왘 Pull the Ziploc ty pe fastenin g strips of the old headband paddings ap art. If necessary , use a pointed tool.
Accessories and spare parts HMEC 26-2 | 21 Accessories and spare parts By changing the cables, you ca n simply retrofit different control units (see page 9 and 10 ) or connectors (see page 23 ) to your headset . Accessories • Cable -CP Cat. No. 500852 •C a b l e -CP-2 Cat.
Accessories and spare parts 22 | HMEC 26-2 Spare parts • Audio cable, len gth 0.6 m, 2 x 3.5 mm stereo jack plug • Audio cable, len gth 0.6 m, 2 x 2.
Product and cable variants HMEC 26-2 | 23 Product and cable variants The following cables, connectors , control units and features are available for the HMEC 26-2 variants (see table on the following pages): 1 Headphhones with +6 dB charac teristic SPL 2 Microphone with 60 mV ou tput voltag e 3 Single-sided round cabl e, 1.
Product and cable variants 24 | HMEC 26-2 * Each -2-1 model is also avai lable as a 2-T model (headphones with +6 dB characteristic SPL and microphone with 60 mV output voltage) Model Cat.
Product and cable variants HMEC 26-2 | 25 123456789<ABCDE FG These headsets can be combined with a ll cables (see page 21).
Specifications 26 | HMEC 26-2 Specifications Headphones Transduce r principle dynami c, closed Ear cou pling supr a-aural Frequency response 20 - 14,000 Hz Impedance HMEC 26-2: 600 Ω mono/1,200 Ω st.
Specifications HMEC 26-2 | 27 Microphon e incl. preamplifier Type HMEC 26-2: BKE 46 HMEC 26-2-1/T: BKE 46-1 Transducer principle pre-polar ized condenser micro phone, noise-compensating Frequency resp.
Connector assignment 28 | HMEC 26-2 Connector assignment Cable -V-KX-2 Cable -CP , -CP-2, -B-CP-2 Cable -NP ¼" (6.3 mm) jack plug P J-068 equivalent 1 2 3 Audio Hi left Audio Hi right Audio Lo 1.
Connector assignment HMEC 26-2 | 29 Cable -RP-2 Cable -DP-2 Cable -KP , -KP-2, -B-K-2 , -B-KP-2, -BV -K-2 Cable -KP / -KP-2 / - B-KP-2 1A u d i o H i 1 N o i s e G a r d ™ ( D C + ) 2 not assigned 2.
Manufacturer Declarations 30 | HMEC 26-2 Manufacturer Declarations W arranty Sennheiser GmbH & Co . KG gives a warranty of 5 yea rs on this product. For the current warranty conditions, please visit our website at www.sennheiser-avi ation.com or www.
Sennheiser electronic GmbH & Co. KG Am Labor 1, 30900 Wedemark, Germany www.sennheiser-aviation.com | www.sennheiser.com Printed in Germany, Publ. 08/12, 548043/A01.
Ein wichtiger Punkt beim Kauf des Geräts Sennheiser HMEC 26-2 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sennheiser HMEC 26-2 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sennheiser HMEC 26-2 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sennheiser HMEC 26-2 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sennheiser HMEC 26-2 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sennheiser HMEC 26-2 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sennheiser HMEC 26-2 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sennheiser HMEC 26-2. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sennheiser HMEC 26-2 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
