Benutzeranleitung / Produktwartung EB3004 MD des Produzenten AVerMedia Technologies
Zur Seite of 50
AVerMedia ® AVerDiGi EB3004 MD User Manual June 2009.
FCC NOTICE (Class A) This device complies w it h Part 15 of the FCC Rules. Op eration is subjec t to the following two conditions: (1) this device may not cause h armful interference, and (2 ) this device must accept an y interference received, including interference that ma y cause undesi r ed op eration.
WARNING TO REDUCE RISK OF FIRE OR ELEC TRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION IF THERE IS ANY DAMAGE, SHORTAGE OR INAPPROPRIATE ITEM IN THE PACKAGE, PLEASE CONTACT WITH YOUR LOCAL DEALE R. WARRANTY VOID FOR ANY UNAUTHORIZED PRODUCT MODIFICATION NOTICE - INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANG E WITHOUT NOTICE.
T able of Content s Chapter 1 Introduction ................................................................................ 1 1.1 Package Cont ent ............................................................................................
1 Chapter 1 Introduction 1.1 Package Content (1) (2) (3) (4) (5) (6) (7) (8) (1) A V erDiGi EB3004 MD unit (2) Remote Control (batteries included) (3) Quick User Guide (4) Power Cord * The power cord varies depending on the standard power outlet of the country where it is sold.
2 Scheduled recording (00:00~23:00 set by hour ) Search for recorded video files by date/time/event Input/Output: 4 sensor input s and 1 relay output control Audio In/Out: 4 audio in and 1 audio out 1.3 Front Panel Name Function (1) DVR Power LED Light when the unit is power on (2) HDD LED Indicate the hard disk runnin g state.
3 Name Function (5) Audio Out Output the audio signal to a audio out device such as speaker i The audio output device ha s it s own power supply is necessary .
4 3. Secure the brackets on the hard disk 4. Connect the the SATA cable and the power connector to the hard disk 5. Secure the hard disk insid e the unit then place unit cover 6. Push the cover forward and secure the cover 7. You may now connect all the cables.
5 1.5.2 Connecting Devices The back panel of the DVR unit, user can connec t up to 4 video cameras, 4 sensor devices, 1 alarm device and output video to a TV or CRT/LCD monitor. Connecting the unit to the PC, then use the bundled software enables user to transfer, playback and segment the video.
6 1.5.3 Connecting the Audio, Sensor and Relay device The Sensor, Alarm, and audio port enable you to connect 4 sensor inputs, 1 relay outputs, and 4 audio in and 1 audi o out device. Just connect the exte rnal sensor, relay, and audio in/out device pin directly to the pinhole.
7 Sensor in and Alarm pinhole: Pin # Definition 11 Sensor 1 signal 12 Sensor 1 Ground signal 13 Sensor 2 signal 14 Sensor 2 Ground signal 15 Sensor 3 signal 16 Sensor 3 Ground signal 17 Sensor 4 signa.
8 Chapter 2 Operating the DVR unit 2.1 Familiarizing the Remote Control Buttons Use the Remote control to operate the OSD menu on surveillance screen. Button Function (1) FN A functional key for multi.
9 Button Function (16) ▼ T o move the sele ction to the left and right ▼ ▲ T o go up and down and select the items in the menu list or change the settings ▼ (17) ZOOM+ T o zoom in view of PTZ camera ZOOM- T o zoom out view of PTZ camera (18) PTZ PTZ camera control button.
10 2.1.1 Using AB Repeat Function AB Repeat function allow user to set a video s egment from A to B point and play on the surveillance screen until user stop. 1. Press ▲ (play button) to call out the SEARCH MODE menu to find the recorded video that user wants to playback.
11 2.1.2 Controlling PTZ Camera Using remote control, user can easily control PTZ camera at local site. Before starting, make sure the PTZ camera is connected with the DVR unit. And then, please go to OSD menu to enable PTZ control (see also 3.1 Menu Function: PTZ Setup ).
12 2.1.2.2 T o Set Preset Position User can set 9 preset positions for PTZ camera. Using 1 to 9 button to set the preset position. 1. Press PT Z and camera channel number button ( 1 2 3 4 ) to enter PTZ mode. 2. Using ▲ , ▼ , ▼ and ▼ to adjust the lens of the PTZ camera to the position that user wants.
13 2.2 Using the DVR for the First Time 1. Make sure all devices and pow er cables are well connected. 2. Turn on the DVR unit by connecting the power cable into the power plug. 3. User should see the SYSTEM INITIALIZE windows appear on the surveillance screen.
14 2.3 Surveillance Screen This chapter will describe the symbols on the surveillance screen and screen display mode. While DVR is playback, the record action will keep working and the surveillanc e screen will playback the recorded video.
15 Playback Mode Symbol Description Playback the recorded video Audio is enabled AB segment is set and playing Recorded video is playback at backwar d speed(2x, 4x, 8x, 16x, 32x, or 64x) Recorded .
16 2.3.1 Setup the Time S t amp Current date and time could be displa yed on each channel screen by enabling TIME STAMP function. Please follow the below steps to enable TIME STAMP . 1. Press to call out OSD menu. 2. Using ▲ and ▼ move the highlight to CAMERA/RECORD and press to make a selection.
17 2.4 Playback the Video If the unit is recording the video, you may have to stop video recording in order to do video playback. To stop video recording, press . 1. Press ▲ (play). 2. Use the ▲ and ▼ buttons to go up and down and select TIME SEARCH , FILE LIST , or SMART MOTION SEARCH .
18 SMART MOTION SEARCH (search by motion event): 1. In SMART MOTION SEARCH window , the ST ART TIME and END TIME show the date and time from when the recording begins and ends. 2. Use the ▲ and ▼ press to set SEA RCH ST ART TIME and SEARCH END TIME for searching period.
19 Chapter 3 OSD Navigation T ree The follow figure is an OSD menu tree m ap. To call out th e OSD menu, press on the remote control..
20.
21 3.1 Menu Function Use remote control to navigate in the OSD menu. The red frame turns yellow when you are making a selection. Each time you change the video display output or video system (NTSC/PAL), the power must be turned off and on to reset the DVR unit.
22 OSD MENU Description GENERAL SETUP RECORD M ODE TIME STA MP DVR NAM E WATERM ARK AUTO RECORD CIF COMPANY W A TERM ARK Enable/disable the reco rded imag e authenticates protection. User can use ImageVerificiation application to identify the image that has been watermark protected.
23 OSD MENU Description CAMERA NAME SETUP CH3 CH2 CH1 CH4 CAMERA1 CAMERA2 CAMERA3 CAMERA4 CHANNEL NAME Give a name for the channel 1 ~ 4. Maximum is 12 characters and can enter A~Z, 0~9, !, “, #, $, %, &, ‘, (, ), *, +, -, /, :, ;, <. >, ?, @, and space.
24 OSD MENU Description MA IN MENU CAMERA/RECORD SCHEDULE EVENT SET UP DISPLA Y STORAGE SYSTEM DISPLAY Configure the parameters of video and setting of sp ot monitor.
25 OSD MENU Description VIDEO OUT SETUP COLOR ENHANCEMENT SHARPNESS VGA MO DE RESOUL TION VGA T V MODE1 - SVGA - 00 00 00 00 VIDEO SHIELD Select the channel and set an area that will be blocking for particular security issue when DV R unit is recording such as enter password for entranc e guard.
26 OSD MENU Description MA IN MENU CAMERA/RECORD SCHEDULE EVENT SET UP DISPLA Y STORAGE SYSTEM RECORD SCHEDULE By default, in 24 hours, the recording schedule is set to always record every hour. Refer to the table below to customize the recording condition.
27 OSD MENU Description MA IN MENU CAMERA/RECORD SCHEDULE EVENT SET UP DISPLA Y STORAGE SYSTEM EVENT SETUP Configure alarm, sensor, a nd motion. EVENT SETUP ALARM SET TING SENSOR SETTING MOTION DET ECTION ALARM SETTING Configure parameters of alarm.
28 OSD MENU Description SENSOR SET UP TYPE ENABLE SENSOR1 SENSOR 2 SENSOR3 SEN SOR4 NO NO NO NO SENSOR Customize the initial state of the attached sensor. ENABLE Active/deactivate the sensor. TYPE Select the state of the sensor. - NO: Indicates that the initial state of the sen s or i s normal open.
29 OSD MENU Description MA IN MENU CAMERA/RECORD SCHEDULE EVENT SET UP DISPLA Y STORAGE SYSTEM STORAGE SETUP To format hard disk an d enable/disable hard disk spaces recycle.
30 OSD MENU Description STOR AGE SETUP HDD SIZE HDD OVERWRITE HDD USED HDD FORMAT 953 , 849MB 279MB 0% 4. After entering the last number, the “ PASSWORD CORRECT ” a ppea rs, you are now authorized to format the hard disk. 5. It is done when the “ FORMAT DISK SUCCESS ” appears.
31 OSD MENU Description SYSTEM SETUP PASSWORD CHAN GE DATE / TIME SYSTEM IN F O AUDIO SETUP INSTANT PLAYBACK LANGUAGE LOG 060 SEC ENGLI SH DATE FORMAT Select the display format of the date -- YYYY/MM/DD, MM/DD/YYYY, or DD/MM/YYYY DATE Set the current date TIME Set the current time Display the latest time synchronization date and time.
32 OSD MENU Description SYSTEM SETUP PASSWORD CHAN GE DATE / TIME SYSTEM IN F O AUDIO SETUP INSTANT PLAYBACK LANGUAGE LOG 060 SEC ENGLI SH PASSWORD CHANGE PASSWORD CHANGE SET UP PASSWORD SE TUP ADMINIST RATOR Enable/disable full system passw ord protection.
33 OSD MENU Description SYSTEM SETUP PASSWORD CHAN GE DATE / TIME SYSTEM IN F O AUDIO SETUP INSTANT PLAYBACK LANGUAGE LOG 060 SEC ENGLI SH AUDIO SETUP AUDIO SETUP AUDIO OUT @ QUAD MUTE CH1 RESET TO DEFAULT 12 3 4 MUTE Enable/disable to hear au dio sound while playback.
34 C h a p t e r 4 Using the USB Playback Console 4.1 Recommended system requirements Pentium®4 2.4GHZ or above Windows®2000/ XP DDR 256 MB Graphic function must support DirectDraw Audio card or built-in S peaker 1 available USB2.0 port 4.2 Installing the USB Playback Console T o install the USB Playback Console: 1.
35 4.3 Running the USB Playback Console To run the application, click the ic on on the PC desktop Name Function (1) Exit T o close the appli cation. (2) Progress bar Show the progress of the file being play ed. Y ou may move the bar to seek at any location of the track.
36 Name Function (4) Open File T o select the video file sou rce fo r playin g. - DVR Recorded File (HD): T o playback the reco rded video from the hard disk which was recording video on the DVR syste m. (see aslo Chapter 4.3.2 ) - Backup File(.dvr): The file is backup and save in *.
37 Name Function (11) Event List Select the ev ent you want to playback. The event list only available when user select to playback in DVR Record ed File(HD) . (12) Camera ID Show the number of camera s that are being viewe d. When you are in single screen mode, click the camera ID nu mber to switch and view other camera.
38 4.3.2 Playback DVR Recorded File from Hard Disk 1. Please hav e the hard disk which containi ng of recorded video data install on your PC or using external USB enclosure to connect to your PC. 2. Click Open File button 3. Select DVR Recorded File(HD) and click OK .
39 4.3.3 Playback Backup File(*.dvr) 1. Click Open File button. 2. Select Backup File(*.dvr) and click OK . 3. Locate the backup file folder and click OK . i When open the backup video file, just loca te the where backup file folder is. 4. And then, Playback Date/T ime Selection window appears.
40 C h a p t e r 5 Backup Recorded Video File HDD Backup application provides user an interfac e to view recorded video from hard disk and backup it. 5.1 Familiarizing with HDD Backup Application Name Function (1) Date Select the date for event s (2) Hour and Channel User can select the hour and channel for events.
41 Name Function (7) Video display Display first frame of each recorded video channel from 4 sele cted. (8) Progress bar Show the progress of the event being played.
42 9. Locate on where user want s to save the backup file 10. Click Star t to process backup 11. T o stop the backup progress, click Sto p 12. T o play the backup file, see 4.
43 Chapter 6 ImageV erification Image V erification is a watermark-checking program to identify the auth enticity of a saved image (e.g. by snapshot). This program can only verify uncompressed bmp image files.
44 Chapter 7 iEnhance The bundled iEnhance is a video editing tool and can only be used with *.dvr video file. It allows you to adjust the video picture quality , segment and save the selected portion of the video, zoom in and out the image, and print or save the screen shot.
45 Name Function (8) Full Screen Use the entire screen to only display the video. (9) Default Set the video back to original st ate and delete all the changes in the history box. (10) History Box List all the act ions. (1 1) Undo Delete the last action.
W arranty Notice LIMITED WARR A NTY AVerMedia TECHNOLOGIES, Inc. warrants this product to be free of defects resu lting from faulty manufactur e or components under the following terms: WARRANTY LENGT.
Ein wichtiger Punkt beim Kauf des Geräts AVerMedia Technologies EB3004 MD (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie AVerMedia Technologies EB3004 MD noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für AVerMedia Technologies EB3004 MD - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von AVerMedia Technologies EB3004 MD reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über AVerMedia Technologies EB3004 MD erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon AVerMedia Technologies EB3004 MD besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von AVerMedia Technologies EB3004 MD verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit AVerMedia Technologies EB3004 MD. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei AVerMedia Technologies EB3004 MD gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
