Benutzeranleitung / Produktwartung STT61V-35BVAC des Produzenten Scag Power Equipment
Zur Seite of 95
PART NO. 03274 Rev. 2 PRINTED 12/2010 PRINTED IN USA © 2010 Scag Power Equipment Division of Metalcraft of Mayville, Inc. Congratulations on owning a Scag mower! This manual contains the operating instructions and safety information for your Scag mower.
W ARNING F AILURE T O FOLLO W SAFE OPERA TING PRA CTICES MA Y RESUL T IN SERIOUS INJUR Y OR DEA TH. Read this manual completely as well as other man uals that came with y our mower . • DO NO T oper ate on steep slopes. T o check a slope , attempt to bac k up it (with the • cutter deck do wn).
I R T able of Contents T ab le of Contents GENERAL INFORMA TION SECTION 1 - ................................................................................... 1 1.1 INTRODUCTION ........................................................................
II R T able of Contents TROUBLESHOO TING CUTTING CONDITIONS SECTION 5 - ...............................................21 ADJUSTMENTS SECTION 6 - ................................................................................................. 24 6.1 P ARKING BRAKE ADJUSTMENT .
III R T able of Contents BDP-16A HYDRA ULIC PUMP ASSEMBL Y ..................................................................................................... 72 BDP-16A HYDRA ULIC PUMP ASSEMBL Y WITH COOLING F AN(29DFI & 35BV AC)) .............
IV R T able of Contents.
1 R Section 1 INTRODUCTION 1.1 Y our mow er was built to the highest standards in the industr y . Howe v er , the prolonged life and maximum efficiency of your mower depends on you f ollowing the operating, maintenance and adjustment instructions in this manual.
2 R Section 1 SYMBOLS 1.4 SYMBOL DESCRIPTION SYMBOL DESCRIPTION Choke T ransmission P arking Brake 48071S Spinning Blade On/Star t Spring T ension on Idler Off/Stop Oil F alling Hazard Thrown Object H.
3 R Section 2 INTRODUCTION 2.1 Y our mow er is only as saf e as the operator . Carelessness or operator error ma y result in serious bodily injur y or death.
4 R Section 2 DO NO T allow children to ride or pla y on the 3. machine, it is not a to y . Clear the area to be mow ed of objects that could be 4. pick ed up and thrown b y the cutter b lades. DO NO T carry passengers. 5. DO NO T operate the machine under the influence of 6.
5 R Section 2 Reduce speed and e x ercise extreme caution on 2. slopes and in shar p turns to prev ent tipping or loss of control. Be especially cautious when changing directions on slopes. Sta y two cut widths a wa y from slopes, drop offs , 3. ditches and retaining walls .
6 R Section 2 Low er the roll bar only when absolutely necessar y . T o lower the roll bar , remove the hairpin cotter pins 1. and remov e the two (2) loc k pins. See Figure 2-2. Lower the roll bar to the do wn position. 2. T o raise the roll bar , lift the bar to the upright 3.
7 R Section 2 W ARNING Failure to pr operly inspect and maintain the seat belt can cause serious injury or loss of life. Check the full length of the seat belt w ebbing f or 1. cuts, w ear , fra ying, dirt and stiffness. See Figure 2-3. Check the seat belt w ebbing in areas e xposed to 2.
8 R Section 2 MAINTENANCE CONSIDERA TIONS & 2.6 ST ORA GE Ne ver mak e adjustments to the machine with the 1. engine running unless specifically instr ucted to do so . If the engine is r unning, k eep hands, f eet, and clothing aw a y from moving par ts .
9 R Section 2 SAFETY AND INSTRUCTIONAL DECALS 2.9 W ARNING INST ALL BEL T CO VER BEFORE OPERA TING MA CHINE READ OPERA TOR'S MANU AL 483402 390S0150i 481568 FOR W ARD REVERSE F R 483397 483406 48.
10 R Section 3 SPECIFICA TIONS ENGINE 3.1 General T ype ................................................................................................Hea vy Duty Industrial/Commercial Gasoline Model: Scag Model STT52V -27CH, STT61V -27CH ...........
11 R Section 3 PO WER HEAD 3.3 Drive System ............... Hydraulic Drive with T wo V ariable Displacement Pumps and T wo Cast-Iron High T orque Motors Hydrostatic Pumps ..................................................................... T wo Hydro-Gear™ 16 cc/re v .
12 R Section 3 HYDRA ULIC SYSTEM 3.5 Hydraulic Oil Filter ........................................................................................................ 10 Micron Spin-on Element T ype Hydraulic Reservoir ....................................
13 R Section 4 CA UTION Do not attempt to operate this mower unless you have read this manual. Learn the location and purpose of all controls and instruments before you operate this mo wer . CONTROLS AND INSTR UMENT 4.1 IDENTIFICA TION Be f or e ope rati ng t he mowe r , f am ili ar ize you rse lf wi th al l mo wer a nd engi ne cont rols .
14 R Section 4 Hourmeter (Figure 4-1). 6. Indicates the number of hours the engine has been operated. It only operates when the engine is running. Has preset maintenance reminders f or engine and h ydraulic system oil changes. Will star t flashing scheduled maintenance 2 hours bef ore preset time and continue flashing until 2 hours after .
15 R Section 4 INITIAL RUN-IN PR OCEDURES 4.3 FIRST D A Y OF USE OR APPRO XIMA TEL Y 20 HOURS Check all belts f or proper alignment and w ear at 2, 4 1. and 8 hours. Change the engine oil and oil filter after the first 20 2. hours of operation. (See Section 7.
16 R Section 4 - IMPORT ANT - Do not tra v el forw ard over a curb . The mow er will hang up on the curb. Raise the dec k and trav el backw ards o ver the curb at a 45 degree angle. (See Section 4.1, items 13 - 15, on page 14 for cutter deck r aising descriptions.
17 R Section 4 HILLSIDE OPERA TION 4.7 W ARNING DO NO T operate on steep slopes. T o c heck a slope, attempt to bac k up it (with the cutter dec k down). If the machine can bac k up the slope without the wheels slipping, reduce speed and use extreme caution.
18 R Section 4 MO VING MO WER WITH ENGINE 4.11 ST OPPED T o “free-wheel” or mov e the mower around without the engine running, rotate the dump v alve lev ers counter- clockwise . See Figure 4-4. Disengage the parking brake and mo ve the mo we r b y hand.
19 R Section 4 Inser t the lany ard pin into the cutting height inde x at 3. the desired cutting height. Push forw ard on the deck lift f oot le ver , hold in place and pull back on the dec k release le ver . See Figure 4-6. Slowly release the f oot pedal.
20 R Section 4 T O WING (OPTIONAL HITCH 4.16 A CCESSOR Y) NEVER allow children or others in or on to wed 1. equipment. T ow only with a machine that has a hitch designed 2. f or towing. Do not attach towed equipment e xcept at the hitch point. F ollow manuf acturer's recommendations f or w eight 3.
21 R Section 5 CONDITION CA USE CURE STRINGERS - OCCASIONAL BLADES OF UNCUT GRASS Width of Deck SGB020 Low engine RPM Run engine at full RPM Ground speed too f ast Slow speed to adjust f or conditions.
22 R Section 5 CONDITION CA USE CURE U N E V E N C U T O N F L A T G ROU N D - W A VY HI G H -L OW APPEARANCE, SCALLOPED CUT , OR R OUGH CONT OUR Width of Deck SGB020 Lift worn from blade Replace blad.
23 R Section 5 CONDITION CA USE CURE SCALPING - BLADES HITTING DI R T OR CUT T IN G VER Y CL OS E T O THE GROUND Width of Deck SGB022 Low tire pressures Check and adjust pressures Ground speed too f a.
24 R Section 6 P ARKING BRAKE ADJUSTMENT 6.1 W ARNING Do not operate the mower if the parking brake is not operable . Possib le severe injury could result. The parking brak e linkage should be adjusted whenev er the parking brake lev er is placed in the “ENGAGE ” position and the parking brak e will allo w the mo wer to mov e.
25 R Section 6 TRA VEL ADJUSTMENTS 6.2 Neutral or trac king adjustments will need to be made if: A. Th e ste eri ng con tro l le v er s are in the neu tr al posi ti on and the machine creeps forw ard or backward. See Neutral Adjustment on page 25 (ne xt procedure).
26 R Section 6 Actuate the steering control lev ers f orward and 6. re verse se v eral times and return them to the neutral position. Check that the driv e wheels remained in neutral and 7. readjust if necessar y . Check that the steering control le v ers hit the stop 8.
27 R Section 6 BEL T ALIGNMENT 6.5 Belt alignment is impor tant for proper performance of your Scag mower . If you experience frequent belt wear or breakage, see your authorized Scag ser vice center for belt adjustment. CUTTER DECK ADJUSTMENTS 6.6 Cutter dec k le v el, pitch and height are set at the f actor y .
28 R Section 6 - NO TE - T o pre vent the cutter deck from teetering, all four (4) cutter deck hanging chains must hav e tension on them. If all f our chains do not ha ve tension on them and the dec k teeters, y ou must readjust the cutter deck as outlined in the procedures abo ve .
29 R Section 6 C . 4-3/ 4" or 5-1/4" P osition - (See Figure 6-9). Placing the baffle in either the 4-3/4" or 5-1/4" setting will enhance f all cutting (leaf pickup) and reduce cutter deck "b low out". T o adjust the Custom-Cut Baffle height: Place the cutter deck in the tr anspor t position.
30 R Section 6 ELECTRIC CLUTCH ADJUSTMENT 6.8 The electr ic clutch ser v es tw o functions in the operation of the mo wer . In addition to star ting and stopping the power flow to the cutter b lades, the clutch also acts as a br ake to assist in stopping blade rotation when the PT O is switched off or the operator presence circuit is interrupted.
31 R Section 7 MAINTENANCE CHART - RECOMMENDED SER VICE INTER V ALS 7.1 HOURS PROCEDURE COMMENTS BREAK-IN (FIRST 10) 8 20 40 100 200 500 X Check all hardw are f or tightness X Check h ydr aulic oil lev el See paragr aph 7.3 X Check all belts f or proper alignment See paragr aph 7.
32 R Section 7 MAINTENANCE CHART - RECOMMENDED SER VICE INTER V ALS (CONT'D) HOURS PROCEDURE COMMENTS BREAK-IN (FIRST 10) 8 40 100 200 500 X Apply grease to fittings See paragr aph 7.2 X Check hardw are f or tightness X Change engine oil filter See paragr aph 7.
33 R Section 7 GREASE FITTING LUBRICATION LUBRICANT / INTERVAL LITHIUM MP WHITE GREASE 2125 ( 40 HOURS / WEEKLY ) CHASSIS GREASE ( 100 HOURS / BI-MONTHLY ) CHASSIS GREASE ( 200 HOURS / MONTHLY ) 4 1 6 3 5 7 2 CHASSIS GREASE ( 500 HOURS / YEARLY ) 390S0145-1 1 8 4 3 9 5 9 2 Lubrication Fitting P oints Figure 7-1.
34 R Section 7 - IMPORT ANT - The h ydraulic oil should be changed if y ou notice the presence of water or a rancid odor to the h ydraulic oil. P ark the mower on a le v el surf ace and stop the 1. engine. Place a suitable container under the h ydr aulic oil 2.
35 R Section 7 STT99CEC ENGINE OIL FILTER DRAIN PLUG Drain Plug and Oil Filter Location Figure 7-5. C. CHANGING ENGINE OIL FIL TER After the first 20 hours of operation, replace the engine oil filter . Thereafter , replace the oil filter after e v er y 200 hours of operation or e very month, whiche v er occurs first.
36 R Section 7 E F 1/4 1/2 3/4 . . . . . FUEL LEVEL FILLER NECK INSERT C.A.R.B. / EP A Phase 3 Fuel Level Figure 7-6. T o av oid personal injur y or proper ty damage, use e xtreme care in handling gasoline. Gasoline is extremely flammable and the v apors are e xplosiv e.
37 R Section 7 - NO TE - In extremely dusty conditions it ma y be necessary to chec k the element once or twice daily to pre ve nt engine damage. Unhook the clamps securing the air cleaner cover to 1. the air filter canister . Remov e the air cleaner cov er and set aside.
38 R Section 7 W ARNING B A TTERIES PRODUCE EXPLOSIVE GASES. Charge the battery in a well ventilated space so gases produced while c harging can dissipate.
39 R Section 7 SGB033 Angle Blade Back Do Not Cut In X Must NOT Exceed 1/3 Blade Width X 30 Blade Sharpening Figure 7-8. Check the balance of the b lade. If the blades are out 2. of balance, vibration and premature w ear can occur . See your authorized Scag dealer f or b lade balancing or special tools, if y ou choose to balance your o wn blades .
40 R Section 7 CUTTER DECK GEARBO X 7.11 A. CHECKING LUBRICANT LEVEL CA UTION The cutter dec k gearbo x can rea ch high operati ng temperatures. Allow the cutter deck g earbo x to cool before servicing. The fluid lev el in the cutter deck gearbo x should be check ed after ev er y 100 hours of operation or bi-weekly , whiche ver occurs first.
41 R Section 7 Replace the radiator cap . Push down on the cap and 3. tur n cloc kwise until it stops. - NO TE - The cooling system should be flushed and the coolant replaced e v er y 500 hours of operation or annually . See y our Scag dealer for proper coolant replacement.
42 R Section 8 NO TES.
43 R Section 8 SCA G APPRO VED A TT A CHMENTS AND A CCESSORIES 8.1 Attachments and accessor ies man uf actured by companies other than Scag P o wer Equipment are not approv ed f or use on this machine .
44 R Section 8 52V CUTTER DECK 44 61 63 69 12 65 64 52 58 54 17 59 24 14 56 28 56 33 3 A A B B 4 14 29 20 53 28 52 24 58 24 52 73 66 32 13 68 55 55 29 58 2 3 23 3 11 50 13 46 60 49 67 24 35 48 9 16 19.
45 R Section 8 52V CUTTER DECK Ref. No. P art No. Description Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39.
46 R Section 8 61V & 72VS CUTTER DECKS 14 15 16 17 23 19 18 5 11 65 66 68 3 4 12 12 64 57 A A B B 1 7 9 8 6 5 3 5 45 62 58 48 56 61 61 7 11 79 57 20 57 84 48 83 2 69 10 26 42 39 21 74 73 23 24 22 .
47 R Section 8 61V & 72VS CUTTER DECKS Ref. No. P art No. Description 61 72 Ref. No. P art No. Description 61 72 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31.
48 R Section 8 CUTTER DECK CONTR OLS STT2006CDC 21 19 37 42 4 6 14 10 42 5 2 3 35 23 41 38 32 34 30 7 27 33 40 41 28 28 24 26 41 40 CUTTER DECK 13 40 39 31 41 40 39 43 9 8 45 20 18 36 16 44 17 41 40 2.
49 R Section 8 CUTTER DECK CONTR OLS Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 461929.
50 R Section 8 SHEET MET AL COMPONENTS STT 2011 SMC 48 50 26 30 25 12 15 19 9 1 23 24 31 32 33 34 29 33 36 37 40 39 38 41 42 43 51 35 44 45 15 27 22 4 20 28 15 14 13 12 11 10 16 17 20 5 8 7 18 18 4 A .
51 R Section 8 SHEET MET AL COMPONENTS Ref. No. P art No. Description Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 .
52 R Section 8 STT R OLL-O VER PRO TECTION SYSTEM 2 3 4 4 2 3 4 3 4 1 1 1 7 8 6 9 5 7 5 11 10 11 6 10 9 2 5 5.
53 R Section 8 STT R OLL-O VER PRO TECTION SYSTEM Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 462210 04001-87 04021-19 04040-13 484168 04001-163 04021-19 484166 484170 484169 484167 STT , ROPS Bolt, He x Head 1/2-13 x 4” Nut, Center Lock 1/2-13 Flatwasher , 1/2-.
54 R Section 8 Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 9292 04001-178 04040-11 483594 482950 482945 482946 482940 482943 482948 482942 482952 482944 482948 482941 04001-12 483440 Suspension Seat Assembly w/seat belt Bolt, He x Head 7/16-20 x 1” Flatwasher , 7/16-.
55 R Section 8 NO TES.
56 R Section 8 DECK DRIVE COMPONENTS STT 2011 DDC B A A B C C Frame 2 1 40 3 47 46 47 43 42 4 41 45 59 53 8 54 72 5 6 64 63 62 7 52 55 9 60 61 10 11 56 52 12 15 65 58 52 14 13 12 20 17 45 18 66 19 67 .
57 R Section 8 DECK DRIVE COMPONENTS Ref. No. P art No. Description Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37.
58 R Section 8 ENGINE AND A TT A CHING P ARTS - K OHLER STT 2005 EAPKH 1 3 7 8 2 5 9 10 9 14 FRAME REF. PUMP MTG. WELDMENT 11 6 15 16 10 12 4 12 10 13.
59 R Section 8 ENGINE AND A TT A CHING P ARTS - K OHLER Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 422593 04017-05 ** 482510 04110-01 424691 483537 ** 484234 04001-19 04030-.
60 R Section 8 ENGINE & A TT A CHING P ARTS - 27HP , 29DFI KA W ASAKI & 35BV A C STT 2009 EAPKA 8 FRAME REF. PUMP MTG. WELDMENT 11 1 3 2 10 12 10 12 10 12 13 14 7 4 A 9 6 10 13 5 A 17 15 16 11.
61 R Section 8 ENGINE & A TT A CHING P ARTS - 27HP , 29DFI KA W ASAKI & 35BV A C Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 451378 4.
62 R Section 8 BRAKE AND STEERING COMPONENTS STT2006B&SC REV 1 A 1 10 11 33 17 9 19 23 41 11 21 34 36 57 73 48 47 46 5 23 53 42 43 44 45 15 56 70 69 71 62 15 65 60 64 67 60 52 41 34 23 51 50 34 35.
63 R Section 8 BRAKE AND STEERING COMPONENTS Ref. No. P art No. Description Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 .
64 R Section 8 STT HYDRA ULIC SYSTEM D D D E F C I H G G F E A A B C DUMP VALVE B 2011 STT HS.eps I H 39 23 24 26 40 34 25 35 21 31 33 9 30 30 11 12 13 7 4 4 3 44 45 17 46 16 14 15 32 5 4 4 5 42 34 25.
65 R Section 8 STT HYDRA ULIC SYSTEM Ref. No. P art No. Description Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37.
66 R Section 8 STT FUEL SYSTEM - EP A PHASE 2 (models pr oduced prior to 1/1/2011) 2011 STT FS - EP A Phase 2.eps Z Z To Injector Fuel Retu rn To Fuel Pump Fuel T ank To Carburetor K ohler Briggs &.
67 R Section 8 STT FUEL SYSTEM - EP A PHASE 2 (models pr oduced prior to 1/1/2011) Ref. No. P art No. Description 1 484251 Fuel Gauge Assembly 2 484242 Seal, Fuel Gauge 3 483792 Fuel Cap 4 04003-02 Bolt, Carriage 1/4-20 x 3/4” 5 462301 Fuel T ank Assembly - STT (incl.
68 R Section 8 STT FUEL SYSTEM - EP A PHASE 3 (models pr oduced after 1/1/2011) 2011 STT FS - EP A Phase 3.eps Z Z 1 2 3 4 5 6 7 8 9 10 10 10 10 11 11 12 To Injector Fuel Retu rn Fuel Ta nk Kawasaki -.
69 R Section 8 STT FUEL SYSTEM - EP A PHASE 3 (models pr oduced after 1/1/2011) Ref. No. P art No. Description 1 484251 Fuel Gauge Assembly 2 484242 Seal, Fuel Gauge 3 484286 Fuel Cap , T ethered 4 04003-02 Bolt, Carriage 1/4-20 x 3/4” 5 462303 Fuel T ank Assembly - STT - (incl.
70 R Section 8 STT -LE FUEL SYSTEM - C.A.R.B. TIER 3 (LE models only - Pr oduced after 1/1/2010) 2011 STT FS - CARB TEIR 3 Re v2.eps Z Z 1 2 3 4 5 6 7 8 9 10 10 10 10 11 11 12 To Injector Fuel Retu rn.
71 R Section 8 STT -LE FUEL SYSTEM - C.A.R.B. TIER 3 (LE models only - Pr oduced after 1/1/2010) Ref. No. P art No. Description 1 484251 Fuel Gauge Assembly 2 484242 Seal, Fuel Gauge 3 484297 Fuel Cap , T ethered (C.A.R.B .) 4 04003-02 Bolt, Carriage 1/4-20 x 3/4” 5 462303 Fuel T ank Assembly - STT - (incl.
72 R Section 8 BDP-16A HYDRA ULIC PUMP ASSEMBL Y OR OR POR T "A" SIDE POR T "B" SIDE Overhaul Seal Kit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 17 18 19 20 20 21 21 22 23 24 25 26.
73 R Section 8 BDP-16A HYDRA ULIC PUMP ASSEMBL Y Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 HG70740 HG51455 HG70735 HG51462 HG51436.
74 R Section 8 BDP-16A HYDRA ULIC PUMP ASSEMBL Y with COOLING F AN (29DFI & 35BV A C)) OR OR POR T "A" SIDE POR T "B" SIDE Overhaul Seal Kit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15.
75 R Section 8 BDP-16A HYDRA ULIC PUMP ASSEMBL Y with COOLING F AN (29DFI & 35BV A C)) Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 .
76 R Section 8 ELECTRICAL SYSTEM (K OHLER & Briggs & Stratton) SCAG POW ER EQUIPME NT 21 1 3 4 5 6 12 13 17 STT 2008 ESKH 10 10 11 17 18 15 14 19 20 22 23 24 25 1 28 27 14 15 9 10 11 8 B B 7 1.
77 R Section 8 ELECTRICAL SYSTEM (K OHLER & Briggs & Stratton) Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 483623 4840.
78 R Section 8 ELECTRICAL SYSTEM - 27HP KA W ASAKI 21 28 27 1 3 4 5 6 13 17 STT2008 ESKA 10 10 11 17 18 15 14 19 20 22 23 24 25 26 28 29 30 14 15 9 10 11 8 B B 7 15 14 16 A 31 18 A C C 12 32 33 2 20 2.
79 R Section 8 ELECTRICAL SYSTEM - 27HP KA W ASAKI Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 481755 48298 483366.
80 R Section 8 ELECTRICAL SYSTEM - 29DFI KA W ASAKI SCAG POW ER EQUIPME NT 21 28 27 1 3 4 5 6 13 17 STT2008 ESKA-DFI 10 11 17 18 15 14 19 20 22 23 24 25 26 28 29 30 14 15 9 10 11 8 B B 7 15 14 16 A 31.
81 R Section 8 ELECTRICAL SYSTEM - 29DFI KA W ASAKI Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 481755 48.
82 R Section 8 REPLA CEMENT DECALS AND INFORMA TION PLA TES 1 2 3 5 8 6 4 9 12 13 7 CHOKE SLO W F AST 482983 48404 STT 2011 Decals 1 W ARNING INST ALL BEL T CO VER BEFORE OPERA TING MA CHINE READ OPER.
83 R Section 8 REPLA CEMENT DECALS AND INFORMA TION PLA TES 481569 R 16 2011 STT Decals Page2 17 19 18 15 481663 481664 20 21 27 14 Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1.
84 R Section 8 STT ELECTRICAL SCHEMA TIC (K OHLER) Kohler STT Schematic Serial No . 7700001 & Higher RELA Y MODULE PLUG POS AMPMETER NEG AMPMETER PT O SWITCH KEY SWITCH ENGINE CLUTCH NEG POS HOURMETER GROUND R.H. NEUTRAL SWITCH 20 AMP FUSE 20 AMP FUSE BRAKE INTERLOCK SWITCH SEA T SWITCH L.
85 R Section 8 STT ELECTRICAL SCHEMA TIC (27HP KA W ASAKI) RELA Y WA TER TEMP GA UGE MODULE PLUG POS AMPMETER NEG AMPMETER PT O SWITCH KEY SWITCH ENGINE CLUTCH NEG POS HOURMETER ST ARTER SOLENOID ST ARTER GROUND FUEL PUMP R.H. NEUTRAL SWITCH 20 AMP FUSE 20 AMP FUSE BRAKE INTERLOCK SWITCH SEA T SWITCH L.
86 R Section 8 ELECTRICAL SCHEMA TIC - 29DFI KA W ASAKI RELA Y WA TER TEMP GA UGE MODULE PLUG POS AMPMETER NEG AMPMETER PT O SWITCH KEY SWITCH CHECK ENGINE LIGHT ENGINE ENGINE ENGINE 20 AMP FUSE CLUTCH NEG POS HOURMETER ST ARTER SOLENOID ST ARTER GROUND FUEL PUMP FUEL PUMP RELA Y MAIN RELA Y R.
87 R Section 8 STT ELECTRICAL SCHEMA TIC (35BV A C Brig gs & Stratton) 31BV Briggs & Stratton STT Schematic RELA Y MODULE PLUG POS AMPMETER NEG AMPMETER PT O SWITCH KEY SWITCH ENGINE AD APTER CLUTCH NEG POS HOURMETER GROUND R.H. NEUTRAL SWITCH 20 AMP FUSE 20 AMP FUSE BRAKE INTERLOCK SWITCH SEA T SWITCH L.
LIMITED W ARRANTY - COMMERCIAL EQUIPMENT Any part of the Scag commercial mower manuf actured by Scag P ower Equipment and f ound, in the reasonable judgment of Scag, to be def ective in materials or w.
© 201 0 Scag Power Equipment Division of Metalcraft of Mayville, Inc..
Ein wichtiger Punkt beim Kauf des Geräts Scag Power Equipment STT61V-35BVAC (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Scag Power Equipment STT61V-35BVAC noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Scag Power Equipment STT61V-35BVAC - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Scag Power Equipment STT61V-35BVAC reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Scag Power Equipment STT61V-35BVAC erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Scag Power Equipment STT61V-35BVAC besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Scag Power Equipment STT61V-35BVAC verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Scag Power Equipment STT61V-35BVAC. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Scag Power Equipment STT61V-35BVAC gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
