Benutzeranleitung / Produktwartung GC-STT-CS des Produzenten Scag Power Equipment
Zur Seite of 28
MODEL GC-STT-CS THIS MANUAL CONT AINS THE OPERA TING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG ACCESSOR Y . READ- ING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSOR Y PERFORMING T O MAXIMUM EFFICIENCY .
F AILURE TO FOLLOW SAFE OPERA TING PRACTICES MA Y RESUL T IN SERIOUS INJURY . * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning.
1 1.1 INTRODUCTION This manual has been prepared to provide the information you need to correctly assemble, operate, and maintain this grass catcher. Read it carefully and keep it for future reference.
2 3. When dumping the hopper into a disposal area: A . Disengage the deck drive, apply the parking brake and allow all moving parts to come to a complete stop. B . Pull downward on the hopper door handle to allow the hopper sweeper to remove the material from inside the hopper .
3 3.1 ASSEMBLY INSTRUCTIONS FOR 52" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
4 RIGHT SIDE OF 52" CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) BLOWER ASSEMBLY MOUNTING POST PIN CARRIAGE BOLTS CATCH PLATE LOCK WASHERS HEX HEAD BOL T ELASTIC STOP NUTS.
5 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 3-3, Page 3. Do not fully tighten the hardware at this time.
6 WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install Art 3-5 18 . Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine.
7 4.1 ASSEMBLY INSTRUCTIONS FOR 61" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
8 RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) BLOWER ASSEMBLY MOUNTING POST PIN CARRIAGE BOLTS CATCH PLATE LOCK WASHERS ELASTIC STOP NUTS AND LOCK WASHERS HEX HEAD BOL TS ELASTIC STOP NUTS GC-STT install art 3 HAIR PIN P R O P E R L Y S E R V I C E E N G I N E W I T H O I L A N D F U E L .
9 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 4-3, Page 8. Do not fully tighten the hardware at this time.
10 WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install Art 3-5 16 . Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine.
11 5.1 ASSEMBLY INSTRUCTIONS FOR 72" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
12 P R O P E R L Y S E R V I C E E N G I N E W I T H O I L A N D F U E L . BLOWER ASSEMBLY MOUNTING POST PIN CARRIAGE BOLTS CATCH PLATE LOCK WASHERS ELASTIC STOP NUTS AND LOCK WASHERS HEX HEAD BOL TS ELASTIC STOP NUTS GC-STT install art 3 HAIR PIN RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.
13 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 5-3, Page 12. Do not fully tighten the hardware at this time.
14 WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install Art 3-5 17 . Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine.
15 FIGURE 5-6 Liquid Cooled Only Note: Illustration is for reference only. Some parts have been removed for visual purposes and may vary depending on model.
16 1. Prepare the work area making sure that it is a clean, safe environment. 2. Remove the rubber strap holding the adapter to the blower assembly. See Figure 5-1. 3. Remove the belt from the spindle pulley. 4. Remove the pin holding the blower assembly to the mounting bracket on the cutter deck and remove the blower assembly.
17 Notes.
18 GC-STT BLO WER HOUSING ASSEMBL Y W A R N IN G INSTALL BEL T COVER BEFORE OPERATING M ACHINE R E A D O P E R A T O R ' S M A N U A L 390STT0200A 1 2 3 3 45 47 45 4 5 6 7 8 9 9 10 10 11 11 12 12.
19 GC-STT BLO WER HOUSING ASSEMBL Y Ref. Pa r t No . Number Description 1 04067-07 Pin, Ring 2-1/4" Long 2 481547 Lanyard, Deck Height Pin 3 04019-02 Nut, Serr .
20 GC-STT BLO WER MOUNTING COMPONENTS 1 2 3 4 5 6 6 7 8 9 10 10 11 12 13 14 15 15 19 20 21 16 17 18 390STT0203 RIGHT SIDE OF 61" CUTTER DECK SHOWN Note: Parts for 52"cutter deck may vary slightly from illustration. Some parts not shown for viewing purposes.
21 GC-STT BLO WER MOUNTING COMPONENTS Ref. Part No. Number Description 1 482406 Belt Cov er , GC-STT - 52" 482378 B e lt C ov e r , GC-STT - 61" & 72" 2 04029-04 Wingnut, Plastic 3/8 Small 3 482300 C ap , Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461419 Adapter , Blow er GC-STT 6 04040-14 Flatwasher , 1/4-.
22 GC-STT -CS HOPPER COMPONENTS A A B B C C CSHOPPEREXPLODE2-STT 1 16 45 15 14 45 43 56 55 6 17 41 50 5 4 3 49 31 51 11 40 58 59 25 12 8 9 34 49 50 24 34 29 42 27 48 38 53 10 33 61 60 37 19 36 20 4 9 .
23 GC-STT -CS HOPPER COMPONENTS Ref. Pa r t No . Number Description 1 461627 Hopper , GC-STT -CS 2 482732 Door , GC-CS 3 461626 Sweeper Weldment, GC-CS 4 482777 Pad, Rubber 5 04090-02 P op Ri v et, 3/16 x .652 6 423834 Plate, Stiffener 7 423831 Suppor t F rame, Hopper 8 423849 Hinge Bracket, L.
24 GC-STT DECALS 481039 482275 482733 482293.
LIMITED W ARRANTY- COMMERCIAL A CCESSOR Y Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor.
P ART NO. 03140 PRINTED 8-2003 PRINTED IN USA © 2003 SCAG POWER EQUIPMENT DIVISION OF MET ALCRAFT OF MA YVILLE, INC www .scag.com.
Ein wichtiger Punkt beim Kauf des Geräts Scag Power Equipment GC-STT-CS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Scag Power Equipment GC-STT-CS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Scag Power Equipment GC-STT-CS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Scag Power Equipment GC-STT-CS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Scag Power Equipment GC-STT-CS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Scag Power Equipment GC-STT-CS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Scag Power Equipment GC-STT-CS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Scag Power Equipment GC-STT-CS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Scag Power Equipment GC-STT-CS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
