Benutzeranleitung / Produktwartung PLV-Z2000 des Produzenten Sanyo
Zur Seite of 60
Multimedia Pr oject or MODEL PL V -Z20 0 0 Owner ’ s Manual http://www.pureglare.com.au.
2 This Multimedia P rojector is designed with the most advanced tec hnology for portability , durabilit y , and ease of use. It uses b uilt-in multimedia f eatures, a palet te of 1 .07 billion colors, and matrix liquid cr ystal display (LCD) tec hnology .
3 TRADEMARKS O Eac h name of corporations or products in this owner ’ s manual is either a trademark or a registered trademark of its respective corporation. T able of Cont ents Feat ures and Design ................ 2 T able of Contents ............
4 CA UTION: T O REDUCE THE RISK OF ELECTRIC SHOCK, DO NO T REMO VE CO VER (OR BACK). NO USER-SERVICEABLE P ARTS INSIDE EX CEPT LAMP REPLACEMENT . REFER SERVICING TO QU ALIFIED SERVICE PER SONNEL. THIS S YMBOL INDICA TES THA T DANGER OUS V OL T A GE CONSTI TU TING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT .
5 All the saf ety and operating instructions should be read before the product is operated. Read all of the instr uctions given here and retain them for later use. Unplug this projector from A C pow er supply before cleaning. Do not use liquid or aerosol cleaners.
6 Moving the Projector When moving the projector , make sure that the automatic slide shut ter is closed, retract the adjust able f eet, and loc k the lens with the Lens Shif t Loc k to prev ent damage to the lens and cabinet. When the projector is unused for an e xtended period, put it into a suitable case.
7 AC P ow er Cord for the Unit ed Kingdom: This cord is already fit ted with a moulded plug incorporating a fuse, the value of whic h is indicated on the pin face of the plug. Should the fuse need to be replaced, an A ST A approved BS 1 362 fuse must be used of the same rating , mark ed thus ASA .
8 Bottom Back Adjustable F eet RGB P anel Cleaning Hole Cover T er minals and Connectors Main On/Off S witch P ow er Cord C.
9 D COMPUTER Connect the computer output signal, or RGB Scart 21 -pin video output to this connector (p.1 6). Rear T erminal D J G 8 L VIDEO Connect the composite video output signal from video equipment to this jac k (p.15). 8 COMPONENT 1 or COMPONENT 2 Connect the component video output signal to these jac ks (p.
10 T op Control D J 8 E G L H < < INFO. but ton Display the input source inf ormation (p.43). G INPUT butt on Select an input source (p.24). 8 LAMP REPLACE indicat or Lights yello w light when the projection lamp reac hes its end of lif e (pp.49, 53).
11 Remote Control J 8 B LAMP CONTROL but ton Select a lamp mode (pp.23, 29). 8 LIGHT butt on Light up the remote control but tons for about 1 0 seconds (p.22). COL OR button Adjust the color intensity of a projected image (pp.23, 28). D POWER ON/S T AND-B Y butt on T urn the projector on or off (pp.
12 T o ensure safe operation, please observe the follo wing precautions: O Use two (2) AA or LR6 type alkaline bat teries. O Al ways r epl ace bat teries in sets. O Do not use a new bat ter y with a used bat ter y . O A void contact with water or liquid.
13 Projection angle can be adjusted up to 6.5 degrees with the adjustable feet. Rotate the adjustable feet and tilt the projector to the proper height; to raise the f eet, rotate the both feet cloc kwise. 1 Adjustable F eet T o lower or to retract the adjustable f eet, rotate the both feet countercloc kwise.
14 The projection lens can be mo ved up and do wn or lef t and right manually with the Lens Shif t Rings, enabling you to adjust the position of a projected image.
15 Video Equipment S-video Cable S-VIDEO Output S-VIDEO VIDEO Composite Video Output Video Cable (RCA x 1) Video , S-video Use a video cable or a S-video cable (commercially av ailable). Unplug the pow er cords of both the pr ojector and ext ernal equipment from the AC outlet befor e connecting the cables.
16 Connecting to a Computer RGB Scar t Use a Scart-V GA cable (optional). Video Equipment COMPUTER RGB Scart 21 -pin Output Scart-V GA Cable Video Equipment HDMI HDMI Cable HDMI Use a HDMI cable (optional) for HDMI output.
17 This projector uses nominal input v oltages of 1 0 0 – 1 20 V or 20 0 – 240 V A C and it automatically selects a correct input v oltage. It is designed to work with the single-phase po wer sy stems having a grounded neutral conductor . T o reduce the risk of electrical shoc k, do not plug into any other type of pow er system.
18 Connect the projector’ s A C pow er cord into an A C outlet and turn the Main On/Of f switc h on. The PO WER indicator lights red. Press the PO WER ON/ST AND-B Y but ton on the top control or on the remote control. The PO WER indicator turns green and the cooling f ans start to operate.
19 Press the PO WER ON/ST AND-B Y but ton on the top control or on the remote control. “P ow er of f?” appears on the screen. Press the PO WER ON/ST AND-B Y but ton again to turn of f the projector . When the P ower of f confirmation function is set to “ Of f , ” the projector can be turned of f without the confirmation message.
20 Press the MENU but ton on the top control or on the remote control to display the On-Screen Menu. Use the P oint ! but tons to highlight or select a main menu item. Press the P oint or OK but tons to access the submenu items. (The selected item is highlighted in ORANGE.
21 Menu and its Functions D J 8 E G L H < D Image Select an image mode from among Brilliant cinema, Creative cinema, P ure cinema, Natural, Living, Dynamic, Vivid, and User image 1 – 7 (p.27). J Image adj. Adjust Brightness, Contrast, Color , Tint, Color temp.
22 Rotate the Zoom Lever to z oom in and out. Rotate the F ocus Ring to focus the image. Zoom Lever F ocus Ring F or some frequently used operations, using the remote control is advisable. Just pressing one of the but tons enables you to hav e the desired operation quic kly , and no need for calling up the On-Screen Menu.
23 Remote Contr ol IMAGE AD J. butt on Press the IMA GE AD J . but ton to display the adjustment bar of the Image adj. Menu items one at a time and directly adjust the selected item. F or details, see page 28. IMAGE AD J. butt on COL OR TEMP . butt on Note: • See the previous page for the description of other buttons.
24 Input Source and System Selection Press the INPU T but ton on the top control or the INPU T but tons on the remote control (see below) to c hoose an input source. T op Contr ol INPUT butt on Press the VIDEO, S-VIDEO , C1, C2, H1, H2, or PC but tons on the remote control according to the input source.
25 Syst em Menu (Video/S-V ideo) If the projector cannot reproduce a proper video image, select a specific broadcast signal format from among P AL, SECAM, NTSC, NTSC 4.43, P AL -M, and P AL -N. Video or S-V ideo Component 1 or Component 2 The projector automatically detects the incoming video sy stem and adjusts itself to optimize its perf ormance.
26 HDMI 1 or HDMI 2 When the video signal is connected to the HDMI 1 or HDMI 2 terminals, select HDMI 1 or HDMI 2 respectively . The projector automatically detects the incoming video signal and adjusts itself to optimize its perf ormance.
27 Press the P oint ! but tons to select the Image Menu and press the P oint or OK but tons to access the submenu items. 1 2 Use the P oint ! but tons to select the desired image mode and press the P oint or OK but tons. The selected item is c heck mark ed.
28 Press the P oint ! but tons to select the Image adj. Menu and press the P oint or OK but tons to access the submenu items. 1 2 Use the P oint ! but tons to select the desired item and press the P oint or OK but tons to access the selected item.
29 Press the P oint but ton to decrease the sharpness of the image; press the P oint but ton to increase the sharpness of the image (from -7 to +7). Shar pness Lamp control Use the P oint but tons to adjust the gamma value to obtain a bet ter balance of contrast (from -7 to +7).
30 This function can be selected only when Adv anced menu in the Set ting Menu (see page 37) is set to “ On. ” Y ou can adjust the follo wing items through this function. Adv anced menu Ir is mode Adjust the lamp apert ure. Select from the follo wing options: Normal .
31 3D-Y/C Optimally separates the color and brightness signal to reduce cross-color and dot interf erence. Press the P oint but tons to c hange the 3D-Y/C mode. Of f .... 3 D - Y / C mode is “ Off ” On .... 3 D - Y / C mode is “ On ” Custom g amma Adjust R, G, B to get the desired balance of contrast.
32 COL OR MANAGEMENT LIST Clear the c heck mark if you do not w ant to apply this adjusted color data to the projected image. Select [Y es] to delete the selected color data. Select the DEL box if you w ant to delete the adjusted data. A confirmation box appears.
33 T o store the adjusted dat a, select Store and press the P oint or OK but tons. The User Image Mode Menu appears. Use the P oint ! but tons to choose one of the se ven (7) user image modes and press the OK or P oint but tons. A confirmation bo x appears.
34 1 Press the P oint ! but tons to select the Picture adj. Menu and press the P oint or OK but tons to access the submenu items. 2 Use the P oint ! but tons to select the desired item and press the P oint or OK but tons to access the selected item.
35 This projector has the pict ure screen resize function whic h enables you to customiz e the image size. Press the P oint ! but tons to select the Screen Menu and press the P oint or OK but tons to access the submenu items. Use the P oint ! but tons to select the desired screen size and press the P oint or OK but tons.
36 Note: • When the video signal format is 720p, 1 080i, or 1 080p, the Screen Menu cannot be selected except for Full, Zoom, Caption in, Normal through , and Natural wide 2. • When Normal is selected with a computer input, the image is projected at the inputted resolution.
37 The language used in the On-Screen Menu is a vailable in English, German, F renc h, It alian, Spanish, P ortuguese, Dutc h, Sw edish, Finnish, P olish, Hungarian, Romanian, Russian, Chinese, K orean, or Japanese. Setting Setting Menu Menu position Menu position This function is used to c hange the position of the On-Screen Menu.
38 HDMI 1 setup/ HDMI 2 set up Select Normal or Enhanced according to the output signal of video equipment. Press the P oint or OK but tons to switch between eac h option. N o r m a l .... When the output of video equipment is set to “ST AND ARD .
39 Rename This function is used to c hange the name of the Input or the User image. Select Rename and press the P oint or OK but tons. The Rename windo w appears. Use the P oint ! but tons to c hoose either Input or User image and then press the P oint or OK but tons to display the rename item selection window .
40 P ow er off confir mation When this function is set to “ On, ” a confirmation dialog box with “P ower of f?” is display ed when turning of f the projector (p.
41 T wo dif f erent remote control codes are assigned to this projector: the factory-set code (Code 1) and the secondar y code (Code 2). This switc hing function prev ents interf erence from other remote controls when sev eral projectors or video equipment next to eac h other are used at the same time.
42 Filter count er This function is used to set a frequency f or the filter cleaning. When the projector reac hed a specified time bet ween cleanings, a Filter warning icon appears on the screen, notifying the cleaning is necessar y .
43 Input Source Information Display The Inf ormation Menu is used for c hec king the status of the image signal being projected and the operation of the projector . Video or S-video A color system of the connected video signal is display ed from among P AL, SECAM, NTSC, NTSC4.
44 The WARNING indicator sho ws the state of the function that protects the projector . Chec k the state of the WARNING indicator and the PO WER indicator to t ake proper maintenance. W ARNING blinking red T OP CONTROL Warning Indicator The projector is shut down and the WARNING indicator is blinking red.
45 Cleaning the RGB panels Blemishes suc h as dust and dirt on the internal optical components of the projector tend to degrade the brightness of the screen and are likely to appear as a shado w on the screen, whic h can lead to deterioration of image qualit y .
46 T urn the projector on and press the MENU button to displa y the On-Screen Menu. Select the Set ting Menu with the P oint ! but tons. Press the P oint or OK buttons to access the submenu items. 1 Put the blo wer’ s nozzle into a hole. 2 Blow air into the projector with the blo wer w atc hing the position of the dust from the screen.
47 The air filter pre vents dust from accumulating on the surf ace of the optical elements inside the projector . Should the air filt er becomes clogged with dust particles, it will reduce cooling fan ’ s ef f ectiveness and ma y result in a buildup of internal heat and adversely af f ect the lif e of the projector .
48 Be sure to reset the Filter counter af ter cleaning or replacing the air filter . Resetting the Filter Counter Filter count er T urn the projector on and press the MENU button to displa y the On-Screen Menu. Select the Set ting Menu with the P oint ! but tons.
49 When the projection lamp of this projector reac hes its end of life, the LAMP REPLA CE indicator emits yellow light. If this indicator lights yello w , replace the lamp with a new one promptly . The time when the LAMP REPLA CE indicator should light is depending on the lamp mode.
50 Be sure to reset the lamp replacement counter af ter the lamp is replaced. When the lamp replacement counter is reset, the LAMP REPLA CE indicator stops lighting . T urn the projector on and press the MENU button to displa y the On-Screen Menu. Select the Set ting Menu with the P oint ! but tons.
51 T roubleshooting Bef ore calling your dealer or service center for assistance, c hec k the items below once again. – Make sure you ha ve properly connected the projector to peripheral equipment as described in “Connecting to Video Equipment” and “Connecting to a Computer” on pages 15 – 1 6.
52 W ARNING: High voltag es are used t o operat e this pr ojector . Do not att empt to open the cabinet. If problems still persist af ter following all operating instr uctions, contact the dealer where you purc hased the projector or ser vice center .
53 Chec k the indicators for projector ’ s condition. • • • green • • • red • • • of f • • • blinking green * When the projection lamp reac hes its end of lif e, the LAMP REPLA CE indicator lights yellow . When this indicator becomes yellow , replace the projection lamp with a new one promptly .
54 Menu T ree Auto PA L SECAM NTSC NTSC 4.43 PA L - M PA L - N Vivid Pure cinema Natural Living Image Image adj. Contrast Color Tint Red Green Blue Noise reduction Color temp.
55 Input Adv anced menu English German F renc h Italian Spanish P ortuguese Dutc h Sw edish Chinese Korean Japanese On / Of f On / Of f Ceiling Rear Quit Russian Scr een F ull F ull through Zoom Caption in Natural wide 2 Overscan Horizontal V ertical Auto adj.
56 Syst em mode H-Fr eq. (kHz) V- F r e q . (Hz) 640x480 31 .47 59.88 640x480 37 .86 7 4.38 640x480 37 .85 72.81 640x480 37 .50 75.00 640x480 43.269 85.00 720x400 37 .927 85.039 640x480 35.00 66.67 832x624 49.72 7 4.55 1 1 52x870 68.68 75.06 800x60 0 35.
57 0.7 4” wide TFT Activ e Matrix type, 3 panels Multimedia Projector 1 6.1 lbs (7 .3 kg ) 1 5.75” x 5.75” x 13.62” (400 mm x 1 46 mm x 346 mm) (not including raised portions) 1 920 x 1 080 dots 6,220,800 (1 920 x 1 080 x 3 panels) P AL, SECAM, NTSC, NTSC4.
58 The parts listed belo w are optional. When ordering these parts, specify item name and T ype No. to the sales dealer . O HDMI Cable T ype No.: PO A -CA -HDMI (This cable is used f or RGB Scart 21 -Pin Video output of video equipment.
59 Dimensions 13.62 (346) 5.82 (147.9) 3.45 (87.7) 6.31 (160.3) 0.77 (19.6) 4.62 (117.3) 3.17 (80.5) 15.75 (400) 2.09 (53) 6.5º 6.06 (154) Unit: inc h (mm) Appendix http://www.
SANY O Electric Co ., Ltd. MD4A http://www.pureglare.com.au.
Ein wichtiger Punkt beim Kauf des Geräts Sanyo PLV-Z2000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sanyo PLV-Z2000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sanyo PLV-Z2000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sanyo PLV-Z2000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sanyo PLV-Z2000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sanyo PLV-Z2000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sanyo PLV-Z2000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sanyo PLV-Z2000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sanyo PLV-Z2000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
