Benutzeranleitung / Produktwartung PJ LINK PLC-XU106K des Produzenten Sanyo
Zur Seite of 79
Multimedia Projector MODEL PLC-XU106 PLC-XU106K Owner ’ s Manual Network Supported □ Wired LAN Refer to the Owner's Manuals below for details about network function.
2 Features and Design This Multimedia Projector is designed with the most advanced technology for portability , durability , and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology .
3 T able of Contents T rademarks Each name of corporations or products in this book is either a registered trademark or a trademark of its respective corporation. Features and Design . . . . . . . . . . . . . . . . . . . 2 T able of Contents . . . . .
4 T o the Owner CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE P ARTS INSIDE EXCEPT LAMP REPLACEMENT . REFER SERVICING T O QUALIFIED SERVICE PERSONNEL. THIS SYMBOL INDICA TES THA T DANGEROUS VOL T AGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT .
5 Safety Instructions All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners.
6 Safety Instructions Openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. CAUTION Hot air is exhausted from the exhaust vent.
7 Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture upward, downward, or backward, perpendicular to the plane of the screen as shown in the figure below .
8 Compliance Federal Communications Commission Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
9 Part Names and Functions ① Infrared Remote Receiver ② Focus Ring ③ Projection Lens ④ Zoom Lever ⑤ Lens Cap (See page 62 for attaching.) ⑥ T op Controls and Indicators ⑦ Air Intake V ent ⑧ Exhaust vent CAUTION Hot air is exhausted from the exhaust vent.
10 Rear T erminal ⑥ S-VIDEO IN Connect the S-VIDEO output signal from video equipment to this jack (p.16). ⑨ AUDIO IN Connect the audio output signal from video equipment connected to ⑥ or ⑩ to this jack. For a mono audio signal (a single audio jack), connect it to the L (MONO) jack (p.
1 1 Part Names and Functions T op Control ① LAMP REPLACE indicator Lights yellow when the projection lamp reaches its end of life (pp.57,63). ⑦ w ARNING indicator – Lights red when the projector detects an abnormal condition. – Blinks red when the internal temperature of the projector exceeds the operating range (pp.
12 Part Names and Functions Note: T o ensure safe operation, please observe the following precautions: – Do not bend, drop, or expose the remote control to moisture or heat. – For cleaning, use a soft dry cloth. Do not apply benzene, thinner , spray , or any chemical material.
13 Part Names and Functions T o ensure safe operation, please observe the following precautions : ● Use two (2) AAA or LR03 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery . ● A void contact with water or liquid.
14 Adjustable Feet Positioning the Projector For projector positioning, see the figures below . The projector should be set perpendicularly to the plane of the screen. Installation Note: • The brightness in the room has a great influence on picture quality .
15 Installation Connecting to a Computer Cables used for connection • VGA cables (Mini D-sub 15 pin) * • Audio cables (*One cable is supplied; other cables are not supplied with the projector .
16 Installation Connecting to V ideo Equipment Cables used for connection • Video and Audio cable (RCA x 3) • S-video cable • Audio cable (Cables are not supplied with the projector . ) Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables.
17 Installation Connecting to Component V ideo Equipment Note: • When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available. • See page 74 for ordering optional cables. Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables.
18 Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100-120 V or 200-240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor .
19 The preparation display will disappear after 30 seconds. (See page 54 for Lamp control status.) T urning On the Projector Connect the projector ’s AC power cord into an AC outlet. The POWER indicator lights red. Open the lens cap (see pages 9, 62).
20 what is PIN code? PIN (Personal Identification Number) code is a security code that allows the person who knows it to operate the projector . Setting a PIN code prevents unauthorized use of the projector . A PIN code consists of a four-digit number .
21 TO MAINT AIN THE LIFE OF THE LAMP , ONCE YOU TURN THE PROJECT OR ON, W AIT A T LEAST FIVE MINUTES BEFORE TURNING IT OFF . Power off? disappears after 4 seconds. T urning Off the Projector Press the ON/ST AND-BY button on the top control or on the remote control, and Power off? appears on the screen.
22 How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. The menus have a hierarchical structure, with a main menu that is divided into submenus, which are furt her d ivide d int o othe r sub menus . For each adju stment and set ting pro cedur e, r efer to resp ectiv e se ctio ns i n th is manual.
23 Menu Bar For detailed functions of each menu, see “Menu T ree” on pages 69-70. ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ Main Menu Sub-Menu ⑨ ⑩ ③ Image select For computer source, used to select an image mode from among Dynamic , Standard , Real , Blackboard(Green) , Colorboard and image 1 - 4 .
24 Rotate the Zoom Lever to zoom in and out. Rotate the Focus Ring to adjust the focus of the image. Zoom and Focus Adjustment Remote Control Auto setup function is provided to automatically execute the setting of Auto setup (includes Input search, Auto PC adj.
25 If a projected picture still has keystone distortion after pressing the AUTO SETUP button on the top control or the AUTO SET button on the remote control, correct the image manually as follows: Press the KEYSTONE button on the top control or on the remote control to switch the Standard (for V ertical/ Horizontal) /Corner adjustment.
26 Sound Adjustment 1 2 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Sound . Press the Ponit ► or the SELECT button to access the submenu items. Press the VOLUME+/– buttons on the top control or on the remote control to adjust the volume.
27 Remote Control Operation Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons enables you to make the desired operation quickly without calling up the On-Screen Menu. Press the COMPUTER 1/2, VIDEO, S-VIDEO and COMPONENT buttons on the remote control to select the input source.
28 black out→ normal → black out → normal → • • • • • Press the NO SHOW button on the remote control to black out the image. T o restore to normal, press the NO SHOW button again or press any other button. The screen changes each time you press the NO SHOW button as follows.
29 Choose Computer 1(RGB) by pressing the INPUT button on the top control or press the COMPUTER 1 button on the remote control. Before using INPUT button, correct input source should be selected through Menu operation as described below .
30 Choose Computer 2 (RGB) by pressing the INPUT button on the top control or press the COMPUTER 2 button on the remote control. Direct Operation Menu Operation Note: When the Input Search function is set to On 1 or On 2 in the Auto setup function, the input signal will be searched automatically (p.
31 PC System Menu PC System Menu Computer System Selection This projector automatically tunes to various types of computers with its Multi-scan system and Auto PC adjustment. If a computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional settings.
32 Auto PC adjustment function is provided to automatically adjust Fine sync , T otal dots , Horizontal , V ertical , Clamp , Display area H and Display area V positions to conform to your computer . PC adjust Menu Auto PC adjustment T o store adjustment parameters The adjusted parameters from the Auto PC adjustment can be stored in the projector .
33 PC adjust Menu Manual PC adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector . Manual PC adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas to store those parameters manually adjusted.
34 Store T o store the adjusted data, select Store and then press the Point ► or the SELECT button. Move the highlight to one of the Modes 1 to 5 in which you want to store, and then press the SELECT button. Mode free T o clear the stored data, select Mode free and then press the Point ► or the S ELECT b utton.
35 Image Select Menu IMAGE button Dynamic Real Image 1 Image 2 Image 3 Image Mode Selection Image 4 Blackboard (Green) Standard Remote Control IMAGE button Select the desired image mode among Dynamic , Standard , Real , Blackboard (Green) , Colorboard , Image 1 , Image 2 , Image 3 , and Image 4 by pressing the IMAGE button on the remote control.
36 Image adjust Menu Image Adjustment Reset Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT button. 1 2 Use the Point ▲▼ buttons select the desired item and then press the SELECT button to display the adjustment dialog box.
37 Store This projector has the picture screen resize function, which enables you to customize the image size. Screen Menu Screen Size Adjustment Provide the image to fit the screen size.
38 Select Digital zoom+ . The On-Screen Menu disappears and D.zoom+ appears. Press the SELECT button to expand the image size. Use the Point ▲▼◄► buttons to pan the image. The Panning function can work only when the image is larger than the screen size.
39 Choose Video or S-video by pressing the INPUT button on the top control, or the VIDEO button or the S-VIDEO button on the remote control. 1 2 Input Menu Input Source Selection (V ideo, S-video) V ideo Input Direct Operation Menu Operation W he n v id e o in p u t s i g n al i s co n n ec t e d t o t he VIDEO jack, select Video.
40 Choose Computer 1(Component) or Computer 1(Scart) by pressing the INPUT button on the top control or pressing the COMPUTER 1 or the COMPONENT button on the remote control. Before using INPUT button, correct input source should be selected through Menu operation as described below .
41 V ideo System Selection 1 A V System Menu (Video or S-video) A V System Menu (Component) 2 If the projector cannot reproduce proper video image, select a specific broadcast signal format from among P AL , SECAM , NTSC , NTSC 4.43 , P AL-M , and P AL-N .
42 Image select Menu Select the desired image mode from among Dynamic , Standard , Cinema , Blackboard (Green) , C ol o r b oa r d , Image 1 , Image 2 , Image 3 , and Image 4 by pressing the IMAGE button on the remote control. Standard Picture mode adjusted with fine tone.
43 Image Adjustment 1 2 Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63). Press the Point ◄ button to decrease the brightness; press the Point ► button to increase the brightness (from 0 to 63).
44 Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15). Gamma Press the Point ◄ button to decrease the sharpness of the image; press the Point ► button to increase the sharpness of the image (from 0 to 15).
45 This projector has the picture screen resize function, which enables you to customize the image size. Normal Screen Size Adjustment Screen Menu 1 2 Provide the image at the 4:3 normal video aspect ratio. Custom Adjust the screen scale and position manually with this function.
46 Language The language used in the On-Screen Menu is available in English , German , French , Italian , Spanish , Portuguese , Dutch , Swedish , Finnish , Polish , Hungarian , Romanian , Russian , Chinese , Korean , japanese , and Thai . Setting Menu Setting Setting Press the MENU button to display the On-Screen Menu.
47 Note: • T h e A u t o K e y s t o n e f u n c t i o n c a n n o t w o r k when the Ceiling feature is set On i n th e Setting Menu (p.52). • P e r f e ct c o r r e c t i on o f t h e i m a ge d i s t o r t i o n cannot be ensured with the Auto setup function.
48 Keystone This function is used to adjust keystone distortion of the projected image. Use the Point ▲▼ buttons to choose the item you want to adjust. Standard Adjust the Horizontal/V ertical keystone distortion of the projected image. Corner correction Adjust the corner distortion of the projected image.
49 Logo (Logo and Logo PIN code lock settings) Logo select This function allows you to customize the screen logo with Logo select, Capture, Logo PIN code lock and Logo PIN code change functions. Note: When On is selected in the Logo PIN code lock function, Logo select and Capture functions cannot be selected.
50 Capture Capture This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations. Select Capture and press the SELECT button. A confirmation box appears and select y es to capture the projected image.
51 Enter a Logo PIN code Use the Point ▲▼ buttons to enter a number . Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to . If you fixed an incorrect number , use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct number .
52 Ceiling Rear Ceiling When this function is set to On , the picture will be top/ bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector . Rear When this function is set to On , the picture will be left/right reversed.
53 On start When this function is set to O n , the projector will be automatically turned on just by connecting the AC power cord to a wall outlet. Note: Be sure to turn off the proj ector properly (see “T urnin g Off the Projector” on page 21).
54 Remote control Lamp control Remote control This projector provides two different remote control codes: the factory-set initial code ( Code 1 ) and the secondary code ( Code 2 ). This switching function prevents remote control interference when operating several projectors or video equipment at the same time.
55 Key lock Key lock Security (Key lock and PIN code lock) PIN code lock This function locks the top control and remote control buttons to prevent operation by unauthorized persons. Select Key lock and then press the SELECT button, and select the desired item by pressing the Point ▲▼ buttons .
56 Use the Point ▲▼ buttons to select Off , On 1 , or On 2 , and then press the SELECT button to make a choice. Change the PIN code lock setting Enter a PIN code Use the Point ▲▼ buttons to enter a number . Press the Point ► button to fix the number and move the red frame pointer to the next box.
57 This function provides the following options in the cooling fans’ operation when the projector is turned off (p.21). L 1 ..... Normal operation L 2 ..... Slower and lower-sound than the normal operation ( L 1 ), but it takes more time to cool the projector down.
58 Factory default This function returns all setting values except for the User logo , PIN code lock , Logo PIN code lock , Lamp counter and Filter counter to the factory default settings. Factory default w arning log This function records anomalous operations while the projector is in operation and use it when diagnosing faults.
59 Input Source Information Display The Information Menu is used for checking the status of the image signal being projected and the operation of the projector . H-sync freq. V -sync freq. Lamp counter Information Menu The horizontal frequency of the input signal is displayed in KHz , or - - - - - when no signal.
60 The W ARNING indicator shows the state of the function which protects the projector . Check the state of the W ARNING indicator and the POWER indicator to take proper maintenance. w ARNING indicator The projector is shut down and the w ARNING indicator is blinking red.
61 Be sure to reset the Filter counter after cleaning or replacing the filters. Resetting the Filter Counter Maintenance and Cleaning T urn off the projector , and unplug the AC power cord from the AC outlet. T urn the projector over and remove the filters by pulling the latches upward.
62 Cleaning the Projector Cabinet Cleaning the Projection Lens Unplug the AC power cord before cleaning. Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner , or use a lens cleaning paper or commercially available air blower to clean the lens.
63 When the p rojection la mp of the proje ctor reaches i ts end of lif e, the La mp repla cement i con app ears on t he scree n and LAMP REPLACE indicator lights yellow . Replace the lamp with a new one promptly . The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.
64 This projector uses a high-pressure lamp which must be handled carefully and properly . Improper handling may result in accidents, injury , or create a fire hazard. ● Lamp life may dif fer from lamp to lamp and according to the environment of use.
65 Problem: – Solutions No power – Plug the power cord of the projector into the AC outlet. – See if the POWER indicator lights red. – Wait until the POWER indicator stops blinking to turn on the projector again. The projector can be turned on after the POWER indicator turns red.
66 No image – Check the connection between your computer or video equipment and the projector . See pages 15-17. – See if the input signal is correctly output from your computer . Some laptop computers may need to change the setting for monitor output when connecting to a projector .
67 The image is distorted or runs off. – Check PC adjustment Menu or Screen and adjust them. See pages 33-34, 37-38. PIN code dialog box appears – PIN code lock is being set. Enter a PIN code (the “1234” or numbers at start-up. you have set). See pages 20, 55-56.
68 w ARNING : High voltages are used to operate this projector . Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center . Specify the model number and explain about the problem.
69 Menu T ree SVGA 1 Mode 1 Mode 2 - - - - T otal dots Horizontal V ertical Display area H Display area V Reset Dynamic Real Blackboard (Green) Image 1 Image 2 Image 3 Image adjust Contrast Brightness Color temp.
70 Auto P AL SECAM NTSC NTSC 4.43 P AL-M P AL-N Video Input Auto 1080i 1035i 720p 575p 480p 575i 480i Dynamic Cinema Blackboard (Green) Image 1 Image 2 Image 3 Normal 0-63 0-63 Off Setting Image selec.
71 Check the indicators for projector condition. • • • green. • • • red • • • off • • • blinks green. When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow . When this indicator lights yellow , replace the projection lamp with a new one promptly .
72 Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V -, H-Frequency mentioned below and less than 140 MHz of Dot Clock. When selecting these modes, PC adjustment can be limited. Note: The specifications are subject to change without notice.
73 T echnical Specifications Mechanical Information Projector T ype Multi-media Projector Dimensions (W x H x D) 13.15" x 3.07" x 10.14" ( 334 mm x 78 mm x 257.5mm ) (Not including protrusions) Net Weight 7.50 lbs (3.4 kg) Feet Adjustment 0˚ to 8.
74 Model No. COMPONENT~VGA Cable : POA-CA-COMPVGA SCART~VGA Cable : POA-CA-SCART VGA-Cable (10 m) : KA-MC-DB10 The parts listed below are optionally available.
75 This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1.
76 COMPUTER IN 1 /COMPONENT IN /COMPUTER IN 2/MONITOR OUT (ANALOG) T erminal: Analog RGB (Mini D-sub 15 pin) 5 1 2 3 4 10 9 6 7 8 15 14 13 11 12 Configurations of T erminals Red (R/Cr) Input/Output Ground (Horiz.
77 Write down the PIN code number in the column below and keep it with this manual securely . If you forgot or lost the number and unable to operate the projector , contact the service station.
78 Dimensions Appendix 10.2 (257.5) 13.15(334) 2.0(51.3) 3.17(80.5) 3.1(78) 5.1(129.0) 5.2(132.0) 2.8(70.5) 5.1(129.0) 4.4(1 12.5) 5.5(140.0) 3.6(91.3) Unit: inch(mm) Screw Holes for Ceiling Mount Screw: M4 Depth: 0.
KB8AC.
Ein wichtiger Punkt beim Kauf des Geräts Sanyo PJ LINK PLC-XU106K (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sanyo PJ LINK PLC-XU106K noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sanyo PJ LINK PLC-XU106K - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sanyo PJ LINK PLC-XU106K reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sanyo PJ LINK PLC-XU106K erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sanyo PJ LINK PLC-XU106K besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sanyo PJ LINK PLC-XU106K verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sanyo PJ LINK PLC-XU106K. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sanyo PJ LINK PLC-XU106K gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
