Benutzeranleitung / Produktwartung ATS-808A des Produzenten Sangean Electronics
Zur Seite of 28
.
FEA TURES Continuous T uning permits reception of Cancel Button allows you to instantly more stations than ever before without change incorrect information keyed into any break on LW , MW or SW bands.
CONTROL LOCA TIONS 1. T elescopic antenna 12. Meter Select Button 2. Sleep T imer 13. Band Selectors 3. Time Set 14. Numeric & Bandwidth Buttons 4. Dual T ime Button 15. Cancel Button 5. Dual T ime Set 16. Enter Command Button 6. LCD Display 17. Memory Entry Button 7.
23. 9KHz/10KHz Step Switch 24. High/Low T one Switch 25. V olume Control 26. Tuning Speed Control 27. Lock Switch 28. Alarm Set Selector 29. Folding Stand 30.
CHOOSING A POWER SUPPL Y Y ou can operate the receiver using: Six Alkaline AA Batteries. Household AC [W ith optional AC adaptor] 12 V olt DC Automobile Battery [With optional DC adaptor] USING BA TTERIES 1. Press latch marked OPEN on both battery ompartment covers in he direction of the arrow and lift off cover.
USING HOUSE CURRENT [AC] The receive may be power by AC current using the AC adaptor (not included). Insert the small barrel shaped plug into the jack on the side of the radio marked DC IN 6V .Plug the other end of the adaptor into a standard household outlet.
PRELIMINARY SETTINGS SETTING THE CLOCK The time is displayed in the 24 hour mode since most shortwave stations operate according to Greenwich Mean Time. This is the standard that is used throughout the world. The clock will start when 4 AA batteries are installed.
4. Now press button marked ENTER . Display shows hours and minutes. 8.
SETTING DUAL TIME A second time zone can be programmed into this unit such as your home time if you are traveling, or Greenwich Mean Time for instant access to short-wave broadcasts or the local time where ever you may be. 1. Press lower "DUAL TIME" button and the display will show "DUAL".
5. Now press button marked "ENTER", Display shows hours and minutes. 6. By pressing the lower "DUAL TIME" button now, the LCD display will once again show the clock time. 7. To verify "DUAL TIME", press the upper "DUAL TIME" button to display your "OTHER" time zone.
BAND SELECTION There are four band selector buttons located just beneath the LCD display . BAND FREQUENCY RANGE PROGRAM TYPE FM 87.5~108 Mhz Standard FM LW 150~519 Khz Longwave MW 520~1710 KHz Standard AM SW 1.71 1~29.999 Mhz SW/13 Sub-Bands 1. Turn radio on by pressing "POWER" button.
TUNING MODE ADJUSTING THE ANTENNA Locate the band you want to listen to in the following chart and adjust the antenna as indicated. BAND ANTENNA TYPES ILLUSTRA TION BAND ANTENNA TYPES ILLUSTRA TION IN.
Y ou may select any frequency using four different turning methods: Direct turning Manual T uning Scan T urning Memory T uning DIRECT TUNING Y ou may "KEY IN" a specific band (120m, 49m,16m) by pressing the appropriate button. The exact station is then selected by pressing the buttons corresponding to the station frequency.
4. Press the button marked ENTER within twelve seconds. The frequency and band will now show up in the display. The SIGNAL STRENGTH will also show. NOTE: Be sure to press the decimal point [ ] in100.70MHz, otherwise the display will show SW , [10.070 MHz] automatically.
MANUAL TUNING To select a station you do not know the frequency of, use the MANUAL TUNING [ ] [V] buttons or the ROT ARY TUNING control on the side of the radio. 1. Press the POWER button to turn on radio. 2. Select a band. 3. Press repeatedly the [ ] or [V] buttons to reach a desired frequency .
When you repeatedly press the [ ] or [V] buttons, the frequencies change in increments of: FM : 50 KHz (or 100 KHz) LW : 9 KHz MW : 9 KHz or 10 KHz SW : 5 Khz 4.
SCAN TUNING Use scan tuning to quickly locate a station or to monitor several stations within a specific band. 1. Turn on radio by pressing POWER button.
4. Press and hold the ( ) or (V) buttons for at least a half second or more and the radio will scan all the frequencies in that band, and will stop automatically each time it lands on an active station. Signal strength is recorded on the SIGNAL STRENGTH INDICA TOR.
MEMORY TUNING Y ou may store up to eighteen different frequencies on the SW/FM bands and up to nine different frequencies on each of the other bands for instant selection of your favorite stations. 1. Press POWER button to turn on radio . 2. T urn to any frequency using any of the previously mentioned tuning methods.
1. Press POWER button to turn on radio. 2. Select a band in which a station is stored that you want to recall. 3. Press any of the NUMBERED buttons for a desired station and the radio will instantly tune to it and display that frequency and the MEMORY position number .
CLOCK RADIO OPERA TION With this receiver you can fall asleep to your favorite station by pressing the SLEEP button, or wake you to the morning news, or an alarm buzzer. Make the following settings with the POWER off! 1. Press ST ANDBY button so display shows 0:00.
POWER 4. T o verify ST ANDBY button again. Press STANDBY once more and the clock returns to the current time. 5. Y ou may select radio or buzzer alarm to wake you by setting ST ANDBY : BUZZER/RADIO selector switch on the side of the radio. 6. T o cancel the ALARM time, press ST ANDBY and C [CANCEL] button.
MISCELLANEOUS CONTROLS In addition to standard tuning methods described previously, use the following controls for special operations. This switch adjusts the receiver's sensitivity . When you listen to a strong station and the signal is slightly distorted, set the switch to the LOCAL position for best reception.
Using the LOCK switch prevents unauthorized operation of the radio and will also prevent the station you are listening to from being changed. When the LOCK switch is moved to its up position, the POWER button ant TUNING controls are completely disabled.
CAR E AN D MAINTENANCE Th i s receiv e r i s a n examp l e o f superior desig n an d craftsmanship . Th e following suggestion s wil l hel p yo u car e fo r the receive r s o tha t yo u ca n enjo y i t fo r years Kee p th e produc t dr y . I f i t doe s ge t wet , wipe i t dr y immediatel y .
26 Wip e th e produc t wit ha dampene d cloth occasionall y t o kee p i t lookin g ne w . D o not us e hars h chemicals , cleanin g solvents , or stron g detergent s t o clea m t o product. Us e onl y fres h batterie s o f th e recommend- e d siz e an d type .
SPECIFICA TIONS Semi conductors: 1 LSI, 9 IC, 8FET. 42 T ransistors 41 Diodes. Circuit: FM : Heterodyne AM (LW , MW , SW) Double-conversion heterodyne Frequency range: FM: 87.5-108 MHz LW : 150-519 Khz MW: 520-1710 KHz SW: 1.711~29.999 Mhz in which divided into 13 shortwave bands 120M 2.
Power sour ces: 1. For Power when not playing radio UM 3 (AA size) battery x 2pcs for memory/clock back-up (3V) 2. For Power to play radio: 1. UM 3 (AA size) battery 4pcs 2. AC adaptor 6V/300 mA center negative Dimension: 196(L) x 125(H) x 36(T) mm Weight: 600 g Accessories: Stereo earphones, Carrying pouch.
Ein wichtiger Punkt beim Kauf des Geräts Sangean Electronics ATS-808A (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sangean Electronics ATS-808A noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sangean Electronics ATS-808A - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sangean Electronics ATS-808A reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sangean Electronics ATS-808A erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sangean Electronics ATS-808A besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sangean Electronics ATS-808A verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sangean Electronics ATS-808A. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sangean Electronics ATS-808A gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
