Benutzeranleitung / Produktwartung SHR-4160P des Produzenten Samsung
Zur Seite of 196
16 Channel DVR SHR-4160N/P User ’ s Manual.
ii Please be sure to keep the following in mind for the right use of the product to pre-vent proprietary risk or damage. ■ Do not use multiple plugs at once. ● This may cause abnormal heat generation or fire ■ Do not put a vase, flowerpot, cup, cosmetics, medicine, or vessel with water around you.
iii W ARNING [Battery] As wrong exchange of the battery in SHR-4160N/P may cause explosion, you shall use the certified battery for SHR-4160N/P . The battery specification is as follows. -Normal V oltage: 3V -Normal Capacity: 220mAh -Continuous Standard Load: 0.
iv Safety Regulations Before we start Standards Approvals Chapter 1 Overview 1. Introduction 2. Features 3. Part Names and Functions Chapter 2 Installation 1. Installation Environment Setup 2. Checking Product & Accessories 3. Additional HDD Installation Chapter 3 Connecting with Other Equipment 1.
v Chapter 5 Menu Setup Before Use 1. System 2. Camera 3. Monitoring 4. Record Mode 5. Event Record Mode 6. Record Schedule 7. Backup 8. Network 9. Network Setup Chapter 6 PTZ Device Control 1. PTZ device Control Mode 2. Basic Operation of P AN, TIL T , & ZOOM 3.
vi Chapter 9 Back up and Back up Search 1. Backup 2. Backup Search Chapter 10 Smart Viewer 1. Introduction 2. Feature 3. PC Specification(Recommendation) 4. Smart Viewer Installation 5. Smart Viewer Program Execution 6. Smart Viewer Initial Screen 7. Monitoring Mode 8.
.
Chapter 1 Over view 1.
1 Intr oduction 1-1 The Digital Video Recorder(DVR) compresses the camera input data from 16 channels into a MPEG4 video file and the voice input data into a G.726 audio file respectively to record them in the Hard Disk or retrieve them from the Hard Disk simultaneously .
2 Features 1-2 ■ 16 CH Composite Input Connectors ■ NTSC/P AL Video Source Compatible ■ Able to record the CIF size (NTSC : 352 x 240 / P AL : 352 x 288) video image at the speed of 360ips(NTSC).
SHR-4160N/P USER’S MANUAL 3 Par t Names and Functions 1-3 Function Channel Button Power LED Network LED Back Up LED HDD Access LED Split Screen Selection Button Mode Selection Button REC Button Display Mode Search Audio Setup Button Displays power on/off condition.
1-4 P ANIC Button REC LOCK Button P ANIC REC LOCK KEY No Name Function ALARM(WIDE) MENU(PRESET) Button ZOOM Button PTZ Button SEARCH ( VIEW ) Button FREEZE(TELE) Button Direction Control Button Search Function Key Video/Audio, set to the system, is recorded to 15 ips(NTSC)/ 12.
SHR-4160N/P USER’S MANUAL 1-5 Caution Caution Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator . T o play DVR on the cabinet or rack, be sure to check the ventilation condition.
.
Chapter 2 Installation 2.
1 Installation Envir onment Setup 2-1 Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator . T o play DVR on the cabinet or rack, be sure to check the ventilation condition. Y ou shall pay attention to the following before you use the product.
2 Checking Pr oduct & Accessories 2-2 Upon delivery of a product, you shall unwrap the product and put it on the even floor or where you want to use it. Then you shall check if the following items are in it. ■ Main Body ■ User’s Manual ■ One Power Cord ■ T wo Brackets - Brackets are used to attach the product to the rack.
SHR-4160N/P USER’S MANUAL 3 Additional HDD Installation 2-3 Y ou may add up to 3 more HDDs to the product. However , since the product contains has many parts which may incur electric shock, acciden.
2-4 2.Detach the cover from the product. (Pull out the cover slightly and lift from the back side to detach.) 3. A bracket is fixed to each side of HDD.
SHR-4160N/P USER’S MANUAL 2-5 4.Pull BRACKET -HDD to the product center to detach the fixed part at the bottom to detach BRACKET -HDD from the product. 5.T ighten 4 SCREW-SPECIALs(BWH,6-32UNC,L10.5), supplied as an accessory to fix HDD to BRACKET -HDD.
2-6 7. Check if BRACKET -HDD has been fixed to the product and connect both the power supply cable and the signal transmission cable (IDE CABLE) to the HDD. Signal T ransmission Cable (IDE Cable) Power Supply Cable 6. Restore HDD installed BRACKET -HDD.
SHR-4160N/P USER’S MANUAL 2-7 8. Check the connector , wiring, and cable fixing condition inside the product and close the cover . 9. T ighten cover-fixing screws. (5 points on both sides and 1 point in the back side) ✻ Y ou can apply 2 HDDs to each BRACKET -HDD as shown in the figure.
2-8 Attention Attention ! Regarding the sub fan, you need additional brackets and sub fans as follows. The sub fan is shaped like this when viewed from the front and back. Please pay attention to the fan direction to let wind go through the fan. @ Fix the fan as follows.
SHR-4160N/P USER’S MANUAL 2-9 # Please install the fan to be seen from the front view of the set..
2-10 $ Fixing the fan to the left..
Chapter 3 Connecting with Other Equipment 3.
1 Connecting V ideo, Audio, & Monitor 3-1 SHR-4160N/P USER’S MANUAL.
3-2 2 Connecting Network ● Connecting to Internet through Ethernet(10/100BaseT) ● Connecting Internet through ADSL.
3 Connecting IEEE1394 Device ● Connect the IEEE1394 hard disk through the back port of SHR-4160N/P . ● Y ou can connect up to 6 IEEE1394 armored hard disks by the Daisy-Chain method. ● After connection, Menu - System - HDD Setup is necessary for recognition and setup for use.
3-4 Note Note Refer to Appendix 2 to see which HDD specifications are supplied..
SHR-4160N/P USER’S MANUAL 3-5 4 Connecting USB Device 1. A total of 2 USB connecting terminals are placed in front of and behind SHR4160N/P each. 2. Connect USB HDD, USB CD/DVD, and USB Memory through the ports in front and behind SHR-4160N/P respectively .
5 Connecting Alarm Input/Output 3-6 The Alarm IN/OUT port in the back of SHR-4160N/P is composed of the following elements. ● ALARM IN/OUT Connection Name Function - ALARM IN1 - ALARM IN2 - ALARM IN.
SHR-4160N/P USER’S MANUAL 3-7 ● ALARM IN/OUT Connection.
6 Connecting RS-485 Device 3-8 ● Connect RS-485 Device through the back port of SHR-4160N/P . ● Y ou can install and control the PTZ device supporting RS-485 communication. ● Y ou can adopt either Half Duplex or Full Duplex method for the connection.
Chapter 4 Live 4.
1 System Motion 4-1 SHR-4160N/P USER’S MANUAL ● T urn the power on and the following LOGO screen pops up. ● After the LOGO screen appears, the button in front of SHR-4160N/P blinks 6 times to initialize the system for operation. ● Upon completion of normal initialization, the Live screen appears accompanying a beep sound.
2 Live screen Mode 4-2 Definition of Live Screen Icon The Live screen icons of SHR-4160N/P display the current setup and function status of each screen. PTZ N CAM_01 CAM_01 V .Loss : Recording Icon Each icon represents Normal / Panic / Event(Alarm+Motion) / Schedule Recording.
SHR-4160N/P USER’S MANUAL 4-3 Definition of Live Screen Mode SHR-4160N/P receives 8 live images and displays them in the following 8 modes. ● Full Screen(Single) Mode: Displays the selected channel in a full screen. Then, the channel LED concerned will be turned on.
4-4 Selecting Live Screen Mode Each mode may be selected by [MODE Button] and [CH1 ~ CH16 Button] The following figure shows Live Mode of SHR-4160N/P after converted.
3 Live Channel Selection and Audio On/Off Setup SHR-4160N/P USER’S MANUAL 4-5 In other split modes than Full Screen Mode, 16 Split Mode, and Screen change Mode, you may choose a channel to be displayed in each split area on your own. Meanwhile, the channel whose MENU is set to Audio On can set up Audio On/Off in all Live Modes.
4-6 4 Freeze and Zoom Freeze Function Freeze pauses the video image in Live Screen, only available in Live Mode. Y ou can set up Freeze On/Off with [FREEZE] button and [FREEZE LED] is turned on or of f depending on the Freeze On/Off setup condition. Zoom Function Zoom enlarges the selected area twice, only available in Full Screen Mode.
5 Event Monitoring Event Monitoring displays the channel synchronized with a specific event (Sensor/Motion/Video Loss) on the screen when it occurs. Event Monitoring On/Of f and Event Duration setup is available in [Menu] ➝ [Monitoring].
4-8 6 Spot-out Monitoring Spot-out Monitoring has nothing to do with Live Screen Output, monitoring the full screen of a certain channel. If you select Monitoring in the MENU screen, you can make a channel among CH1 to CH16 spot out or you can output channels one by one at an interval as Screen change Mode of Live Mode.
Chapter 5 Menu Setup 5.
Before Use 5-1 ● Selection The yellow cursor shows the current window . Use the , ❷ , ➛ , ❿ button in the front to move the cursor on your desirous menu. If you press the “ Enter ” key with the cursor clicking on your desirable menu, the system will enter the new mode.
1 System 5-2 ● System Menu has the following items in detail. ● Date Press the “ Enter ” button and the ➛ or ❿ button to move to Y/M/D. Use the or ❷ button to change the date. Press the “ Enter ” button to come out of the mode. ● T ime Press the “ Enter ” button and the ➛ or ❿ button to move to H/M/S.
SHR-4160N/P USER’S MANUAL 5-3 ● Date Format This supplies 3 formats, Y ear-Month-Date / Date-Month-Y ear / Month-Date-Y ear . ● T ime Format This supplies 2 formats, 24 Hour / 12 Hour(AM/PM). ● Language After you select a language, OSD is expressed in the selected language.
5-4 Password ● The Default Password is 4321. ● New Password This is used to change the system password inside SHR-4160N/P . Y ou are allowed to create a password up to 8 digits. Press the “ Enter ” button and then a channel button from 0 ~ 9 on your left to finish input.
SHR-4160N/P USER’S MANUAL 5-5 Load Factory Default ● This initializes all the menu preset values. The recorded data will not be deleted. Press “ OK ” in the confirmation window to start initializing. System Log ● System Log is used by a controller to check crucial records.
5-6 ● System Log List Event Log ● Checks the record regarding Event like Alarm / Motion / Video Loss ● This displays the contents of a log regarding Event its execution date/time. ● First : Returns to the first page. ● Prev : Back to the previous page.
SHR-4160N/P USER’S MANUAL 5-7 System Information and Setup ● Software V ersion : Displays the current version. Setup is not available. ● Broadcast Format : Displays the current Format(NTSC/P AL). Setup is not available. ● Mac Address : 6 Byte hardware address.
5-8 HDD Setup ● HDD Information Displays the number , quantity , and status of A T A, IEEE1394, and USB. Setup is not available. Status : Internal HDD, External HDD, Backup HDD ● External HDD setup 1. Backup/External Y ou are able to determine the usage of IEEE1394 and USB.
SHR-4160N/P USER’S MANUAL 5-9 ● USB Device Setup Y ou can set up USB Memory/USB CD(DVD). If you want to stop using the USB device, you are recommended to press "Disconnect" first before you pull out the device from the main body . HDD Mode Setup ● Repeat recording of HDD Stop : Stops recording when HDD is full during recording.
5-10 Remote control Device ● MENU for Samsung Integrated Remote Control(SSC-2000) Remote Control Device ID Baudrate Device Samsung System Keybord Parity Date Stop Duplex 03 4800 None 8 1 Half Duplex ● Device A Remote Control Device, being connected to the RS485 port.
SHR-4160N/P USER’S MANUAL 5-11 System Shutdown ● T erminates the work in action safely and turns the power off. Press “ OK ” in the confirmation window and plug out when you see “ Safe to Power Off ” .
5-12 2 Camera ● The detailed Camera Menu items are as follows. ● Video On : Camera images from a selected channel appear . Off : Camera images from a selected channel disappear . Covert1 : Displays other information than the image information on the selected channel.
● T itle Y ou can name the camera of a selected channel. If you press the [Enter] button, the Virtual keyboard will come out. ❿ Virtual Keyboard If you move the cursor , you can type text by text. Up to 15 texts can be typed. Keyboard cannot be composed of all spaces.
5-14 PTZ Device ● ID PTZ device ID from 0 to 255 ● Protocol A protocol supported by PTZ device The following protocols are now being supported. Samsung / Vic.
Screen Setup SHR-4160N/P USER’S MANUAL 5-15 ● This is a window to adjust Brightness/Contrast/Color for the camera image of each channel. Put the cursor on the channel that you want to adjust and set up Brightness/Contrast/Color . Once selected, the channel appear in the PIP area on the right.
5-16 3 Monitoring ● Event Monitoring Y ou are able to set to Off/3sec/5sec/10sec/20sec/30sec/Continuous. ① Off : Event Monitoring does not operate to turn to the screen where an event occurs. ➁ 3sec/ 5sec/ 10sec/ 20sec/ 30sec : For the period, the screen is seen before the next screen appears.
● Monitor Out Y ou may not use both VGA Output and Composite/S-Video Output at the same time. Accordingly , the user shall choose either one. ① Composite : The output will come out from the "Composite / S-Video Output" port. ➁ VGA : Output comes out of the “ VGA Out ” port.
5-18 4 Record Mode If you press the front “ REC ” button, the mode to be recorded will be determined. ☛ For Event Recording Mode value setup, refer to 5-19. Event Record Mode Setup Menu. ● Mode On : Pressing the REC button starts recording the current channel.
5 Event Record Mode ● The detailed items of Event Record Menu are as follows. Evnet Record Mode Determines a mode to be recorded when an event occurs.
5-20 ● Quality Recording resolution will be determined. HH(V ery High)/H(High)/N(Normal)/L(Low). ● Note The resolution Full D1 can be set from the 7.5ips(NTSC)/6.25ips(P AL) recording frame. The resolution Halfl D1 can be set from the 15ips(NTSC)/12.
Alarm Detection Setup ● Sensor State Off : Sensor does not operate. ① N.O(Normal Open) Sensor : Sensor remains open all the time and if closed, an alarm will be issued. (A Contact) ➁ N.C(Normal Close) Sensor : Sensor remains closed all the time and if open, an alarm will be issued.
5-22 Motion Detection Setup ● M.D State Off : Motion Detection does not operate On : Motion Detection starts operation. ● Area Select the Motion Detection zone. It is composed of 45x40(NTSC) / 45x48(P AL) sized Block. Y ou are forbidden to determine 4 block rows(Up/Down/Left/Right) to allow them to be displayed in all monitors.
● Sensitivity Determines Motion sensing sensitivity . Sensitivity grade consists of Low ➝ Medium ➝ V ery High in the ascending order . ● Alarm-Out Selects Alarm-Out scope when Motion occurs. At this moment, this supports 5 Alarm Outs. Choose an alarm-out that you want to synchronize with the current motion channel.
5-24 6 Record Schedule Y ou may select a time when recording starts automatically . Setup by the weekday or time. The default is set to “ None ” . ● Pressing “ CH > “ copies the value of Channel 1 to all the channels. ● The horizontal axis numbered from 0 to 23 represents the time value.
● Both(Continuous, Event) On occurrence of Event, Continuous Recording is replaced with Event Recording Mode. ● Holiday If you press “ Holiday ” , a calendar pops up and you are able to designate holidays. Move to a date and press “ Enter ” to complete designation.
5-26 7 Backup ● In the presence of the device, the free space and backup device will be displayed. ● Select the backup date and time and the camera number , then press "Start". ● Whenever you change the start date/time, the end date/time, the free space is updated and displayed.
SHR-4160N/P USER’S MANUAL 5-27 USB Device Backup Setup Caution Caution [In the Backup process] Press "Cancel" to return to the upper menu but the process continues nevertheless. Press "Stop" to suspend backup Backup may retard the normal set speed.
8 Network 5-28 ● Connection Mode Designates the kind of the network connected to the main body of SHR-4160N/P . Static IP : When the main body is connected to the network with Static IP . Dynamic IP : When the main body is connected to the network with Dynamic IP supplied by DHCP .
SHR-4160N/P USER’S MANUAL 5-29 Caution Caution IIn the ADSL connection mode, SmartV iewer does not support Audio replay . Caution Caution Be sure to set up IP/SubnetMask/Gateway/DNS to let Smart V iewer connect with the main body of SHR-4160N/P .
5-30 Note Note If you want to connect IP Router with the main body of SHR-4160N/P , you shall designate a port for SHR-4160N/P in the IP Router setup menu. The SHR-4160N/P main body uses 4 ports for TCP communication and further 160 UDP ports when the procotol type is set to UDP .
SHR-4160N/P USER’S MANUAL 5-31 Callback Settings ● Callback delivers a callback message to the IP where SmartV iewer is already running when an event corresponding to Alarm, Motion Detection, or Video Loss occurs from the set. ● On/Off : Of f is the default and On is optional.
9 Network Setup 5-32 Port setup for SmartViewer connection. ● The port value shall be the same as the Port(TCP/IP) value of the set to regis- ter DVR(Setup ➝ Site Setup) with SmartViewer . ● When you use an IP router , you shall forward the activated port by the current setting value.
Chapter 6 PTZ device Contr ol 6.
1 PTZ device Contr ol Mode 6-1 ● Select a proper PTZ Device Configuration value in MENU to enter PTZ Control Mode. ● Selected in MENU, the symbol( ) of PTZ is displayed on the channel in the screen. ● If you press the Enter( ) button among direction keys in front of Split Screen, a blue bar will appear in the monitor screen.
6-2 ● Other PTZ device Control Modes perform its control in a single screen. Press the channel selection button in the left front to select the channel whose Menu select- ed PTZ and then press the PTZ button.
SHR-4160N/P USER’S MANUAL 2 Basic Operation of P AN, TIL T , & ZOOM 6-3 ● PA N Press the LEFT or RIGHT button in front SHR-4160N/P in PTZ device Control Mode to control PTZ device horizontally . ● TIL T Press the UP or DOWN button in front SHR-4160N/P in PTZ device Control Mode to control PTZ device vertically .
3 PRESET Setup 6-4 ● Records a certain position of PTZ device. ● Memorizes up to 20 PTZ device positions at the moment. ● Press the SET button in front of SHR-4160N/P in Single Screen PTZ device Control Mode to set up Preset. ● After PRESET setup, press ENTER.
SHR-4160N/P USER’S MANUAL 6-5 ● Move the cursor right and press ENTER in PTZ Control Mode first. Then, press Enter to run P/T/Z/ Motion Mode in the PIP screen and press Enter again to cancel P/T/Z/ Motion Mode. ● Press Enter at the Position Name position to see Virtual Keyboard.
4 Camera Menu Setup 6-6 ● Camera Menu is a menu supplied by PTZ device itself. This Menu sets up several conditions of PTZ device. ● Press the SET button in front of SHR-4160N/P in Single Screen PTZ device Control Mode to select Camera Menu.
SHR-4160N/P USER’S MANUAL 5 Preset V iew 6-7 ● Preset setup allows your movement to a certain saved position of PTZ device. ● Press the VIEW button in front of SHR-4160N/P in Single Screen PTZ device Control Mode to select Preset.
6 Other V iew 6-8 ● Press the VIEW button in front of SHR-4160N/P in Single Screen PTZ device Control Mode to supply PTZ device. This is a very special function. ● After you select a function, press Enter . Then the function will be checked and start running.
Chapter 7 Recording 7.
1 P ANIC (Emergency Recording) 7-1 ● Pressing the button records all the images input so far . Emergency Record has the characteristics of CIF size, V ery High resolution, and 15ips(NTSC)/12.5ips(P AL). During P ANIC Recording, LED lights on and a recording icon appears on the screen.
2 REC (Normal Recording) 7-2 ● Pressing REC the button starts recording as set in Record Mode of MENU. Then, REC LED lights on and a recording icon appears on the screen. During recording in HDD, HDD LED in front blinks. ● During REC Recording, you may stop REC Recoding by pressing the REC button then REC LED lights out.
SHR-4160N USER’S MANUAL 3 Record Schedule 7-3 ● While “ Continuous Recording ” or “ Both ” is selected for Record Schedule in MENU, T imer Recording automatically starts. Otherwise, T imer Recording remains inacti- vated. During T imer Recording, Recording Icon appear on the screen.
4 Event Recording 7-4 ● Alarm Detection Sensor State in Event Record Alarm of MENU shall be set to N.O (Normal Open) or N.C (Normal Close) ● Motion Detection M.D State in Event Record Motion Detection of MENU shall be set to On. ● Video Loss Detection Image Loss State in Event Record Image Loss of MENU shall be set to On.
Chapter 8 Search & Play 8.
Before Use 8-1 ● Pressing the SEARCH button shows Search Menu on the screen as seen above. ● CALENDAR uses a calendar to search video files at the preset time. ● Event Search searches video files recorded by Event. ● Date/T ime inputs a day and time on which the system searches video files.
1 Calendar Search 8-2 ● Be sure to designate both the channel and the date first. Then press [Start] button to initiate search. ● Uses a calendar to search video files at the preset time.
SHR-4160N/P USER’S MANUAL 8-3 ● Searches Normal Recording, Panic Recording, Sched.(Schedule) Recording, Alarm Recording, Motion Recording, and Image Loss Recording by the time. ● Y ou shall select a channel to search to see the Event information of the channel.
3 Date/Time Search 8-4 ● Use the Day/T ime information to search video files at the time as you desire. Up to 4 channels can be searched at once. ● Press , ❷ , and [Enter] to select a channel and the box on the right of the chan- nel will be checked.
SHR-4160N/P USER’S MANUAL 8-5 ● Searches the oldest one among recorded video files. Up to 4 channels can be searched at once. ● , ❷ , Press [Enter] to select a channel and the box on the right of the channel will be checked. ● Press [Start] to start searching and press [Cancel] to return to the previous menu.
5 Go to Last Search 8-6 ● Searches the latest one among recorded video files. Up to 4 channels can be searched at once. ● , ❷ , Press [Enter] to select a channel and the box on the right of the channel will be checked. ● Press [Start] to start searching and press [Cancel] to return to the previous menu.
Note Note - Pressing the PLA Y button( ) does not af fect play as far as the user stays in MENU. Be sure to escape from MENU to start play . ● Press the STOP button( ) to stop play . If you press the Playback/P AUSE button( ), recording will resume from the point where the previous recording stops.
8-8 ● Play Screen Mode Definition 16 Split Screen PIP Screen Single Screen 4 Split Screen 9 Split Screen Whenever you press [Mode], the Play screen becomes 4Split, Single, PIP , 9Split, 16Split in turn. If you select only one channel from Searh, the 4 Split screen will not appear .
● Play at Faster Speed If you press the LEFT or RIGHT button( / ) or use the Shuttle during play , you will be able to see the screen at the x2, x4, x8, x16, x32, and x64 speed either forwardly or reversely .
Chapter 9 Backup and Backup Search 9.
1 Backup 9-1 1. IEEE1394 HDD and USB HDD 1.1 Backup Start Before backup, HDD(IEEE1394, USB) shall be connected for such purposes. ① Choose either IEEE1394 HDD and USB HDD as a backup device. ➁ Select a backup channel and change the tiem when back starts and ends.
9-2 2. CD/DVD and USB Memory 1.1 Backup Start ① Choose USB Memory or USB CD/DVD as a backup device. ➁ Select a backup channel and change the tiem when back starts and ends. ➂ The backup video file size shall be maintained below the free space of USB Memory and USB CD/DVD.
SHR-4160N/P USER’S MANUAL 9-3 Caution Caution 1. During backup, you shall not separate the backup device from SHR-4160N/P . 2. During backup search, you shall not separate the backup device from SHR- 4160N/P .
2 Backup Search 9-4 1. Backup search menu 1-1. External HDD Search ● If you select an external HDD, you may search the data by using Date, Event, Origin, or Late.
SHR-4160N/P USER’S MANUAL 9-5 ● Use the weekday/time information in the backup image to search images contained in as many as 4 channels. ● Click , ❷ , [Enter] to select a channel and the box on the right of CH No. shall be checked. ● After channel selection, click the ❷ button to move to the time search line.
Chapter 10 Smar t V iewer 10.
1 Intr oduction 10-1 SHR-4160N/P USER’S MANUAL Smart Viewer is a program that a general PC user is able to install SHR-4160N/P to his PC to monitor the search video and audio data through Network without going to the site where SHR-4160N/P is installed by himself.
2 Feature 10-2 ● Thanks to the transmission of video data compressed by the MPEG-4 Video Compression method, this plays video images of good quality . ● Thanks to the G.726 V oice Compression method, this supplies voice data of good quality . Use of armored MIC improves the quality of remote voice.
SHR-4160N/P USER’S MANUAL 3 PC Specification(Recommendation) 10-3 ● OS : Win98SE, WinMe, Win2000, WinXP ● Recommendation : CPU P3 1GHz or higher RAM 256 Mb or higher VGA RAM 32Mb or higher DirectX 8.
4 Smar t V iewer Installation 10-4 Smart Viewer Installation ● Put a Smart Viewer Program CD in and open the “Smart V iewer” folder in CD. ● Run the “Setup.
SHR-4160N/P USER’S MANUAL 10-5 ● Click the “Next” button. ● If you agree with Smart Viewer License, click “Y es”. ● Designate a folder to install Smart Viewer in it and click “Next”.
10-6 ● The system proceeds with setup file installation and system setup. ● Installation is complete. Press “Finish” to terminate installation.
SHR-4160N/P USER’S MANUAL 5 Smar t V iewer Pr ogram Execution 10-7 ● Double-click the Smart Viewer icon in the background screen to run the program.
6 Smar t V iewer Initial Screen 10-8 ● Screen Description ! Pressing this button enters Search Mode in which you can search and play the video data recorded both in Monitoring Mode for real-time video data monitoring and in SHR-4160N/P . @ This button terminates or minimizes the program.
SHR-4160N/P USER’S MANUAL 7 Monitoring Mode 10-9 ● DVR(SHR-4160N/P)/SITE Connection - Select the name of DVR(SHR-4160N/P) or site for connection and click the connection button.
10-10 ● Monitoring Mode Connection Screen ● Mode Conversion Button - This button changes Monitoring Mode or Search Mode. Note Note No more than 3 users, one Admin. authorized user and 2 User authorized users are allowed to access SHR-4160N/P simultaneously .
SHR-4160N/P USER’S MANUAL 10-11 ● Ti me Information - As soon as you are Connected to SHR-4160N/P , the date, weekday , and time of the set to which the selected channel is connected. - If SHR-4160N/P is not connected, the present date, weekday , and time of the user's PC are displayed.
10-12 Note Note # Clicking the speaker icon turns Audio of a channel on or off. : Audio OFF : Audio ON If you turn Audio of a SHR-4160N/P channel of f, Disable will be displayed. : Audio Disabled ✴ For the channel with Audio turned on now , use the following Audio relate button to control Audio volume and set up MUTE.
SHR-4160N/P USER’S MANUAL 10-13 ● Event Log Display Window - Click the Log button to activate the Log Display window . - Displays the event(alarm, user connection, and setup change) occurring at SHR-4160N/P real time. Note Note [Event Message] Connecting.
10-14 Caution Caution When Time Change, Load Factory Default, Network Change, System Shutdown, or Hdd Format event occurs, Smart V iewer terminates automatically . ● Camera Connecting Indication Window - List displays the connection condition of DVR and CAMERA.
SHR-4160N/P USER’S MANUAL 10-15 ● Monitoring Screen Condition Information / Selection Button - Displays the Split or Monitoring condition of the screen in play .
10-16 : During monitoring in Quad Mode : During monitoring in Single Mode : Camera Off Note Note The figure in a screen icon indicates the screen position in SmartV iewer . : The orange icon indicates the current channel is connected to a camera. : The gray icon indicates the channel is connected to a camera but not displayed on the screen.
SHR-4160N/P USER’S MANUAL 10-17 ● NEXT Button - Click NEXT(Mouse Left Button) to see the channel next to the current monitoring channel. - In Single Mode : 1 ➝ 2 ➝ 3 ➝ 4 ➝ 5 ➝ 6 ➝ 7 .
10-18 ● FA VORITE Button - Click the F A VORITE button to activate the F A VORITE window . Click the current F A VORITE to display all the cameras recorded in the settting. Y ou may delete all the selected F A VORITE settings or all the F A VORITE settings.
Note Note The adjusted Audio volume, brightness, and contrast values will be saved in your PC and remain unchanged even if you terminate Smart V iewer and restart it.
● PTZ device Control Buttons - Select a channel connected to PTZ device to control PTZ related functions. - P AN Left / Right - TIL T Up / Down - Diagonal Control - The channel under PTZ control will be displayed in the center of the button. 10-20 Note Note The P AN / TIL T / ZOOM function is supplied to all camera.
If you click the current PRESET number and name, the camera will move accordingly . Y ou can delete the selected or all PRESET setup values. Y ou can set up a new PRESET number and name. SHR-4160N/P USER’S MANUAL 10-21 Note Note ! The PRESET function is supplied to all camera.
10-22 Note Note The Camera Menu Setup function is supported by Samsung and Panasonic. ● Self Menu Setup of PTZ device ! This is a Menu screen supplied by the camera itself, seen from V iewer . @ Use the / / / button for the movement between menus.
SHR-4160N/P USER’S MANUAL 8 Search Mode 10-23 ● Description of Search Mode Initial Screen - Search Mode is divided into Remote Mode for SHR-4160N/P image search/play and Local Mode to play .
10-24 ● DVR(SHR-4160N/P)/SITE Connection - Same as “DVR(SHR-4160N/P)/SITE Connection” of Monitoring Mode. ● Remote Mode - This mode sends out the video data recorded in SHR-4160N/P to Network for play . - Up to 4 channels are allowed for simultaneous search and play .
SHR-4160N/P USER’S MANUAL 10-25 ● Calendar Window - If the video data in on-line SHR-4160N/P was recorded, the date turns red. - If you click the date in red, the saved video data will be displayed. - The currently selected date will be marked with a thick red box.
10-26 ● V ideo Record / Convert File / Print / Setup ! V ideo Record Button - If you select a channel in play and click the SA VE button, the image will be saved in a file format with the extension of .
SHR-4160N/P USER’S MANUAL 10-27 # Print - This function outputs the screen zone of the image in play which is now being displayed. $ Setup Mode Button - This button pops up the Setup Mode window .
10-28 Note Note During play(Play/RevPlay/FF/FB), disconnection or entering both Monitoring Mode and Local Mode is not permitted. Click the Stop button first before conversion. Note Note Double-clicking the neighborhood of Time Bar enters Zoom In Mode.
SHR-4160N/P USER’S MANUAL 10-29 ● Next Button - Changes a channel as the Next button does in Monitoring Mode. ● Reload Button - Clicking updates the time information on the video data recorded in the calendar window and T ime Line. ● Local Mode - This mode plays .
9 SETUP MODE 10-30 ● Description of Initial Screen ! This button is used to select items for DVR Setup, Viewer Setup, Site Setup, and S/W V ersion setup. @ Shows what the selected Setup item can set up in detail. # This button terminates the Setup window .
SHR-4160N/P USER’S MANUAL 10-31 ● Setup Item Selection Button - This button is used for the selection of each Setup item. - This is composed of 4 items, DVR Setup, V iewer Setup, Site Setup, and S/W V ersion. - DVR Setup : DVR Setup allows you to change the remote Menu setup items of SHR-4160N/P .
10-32 DVR Setup - Click the [DVR Setup] button for DVR Setup. - Y ou can change the setup items of SHR-4160N/P Menu, being connected with Smart Viewer remotely . - DVR Setup is composed of 5 items, System, Camera/Audio, Monitoring, Recording, and Network.
SHR-4160N/P USER’S MANUAL 10-33 ● Detailed DVR Setup Items ! System - Information Information shows the information on on-line SHR-4160N/P . Note Note For the detailed items of DVR Setup, refer to Chapter 5, MENU. - Password Password determines the password for the control of SHR-4160N/P Menu or SHR-4160N/P key input.
10-34 Note Note - The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not supplied to System Password input. - Use the BACKSP ACE key to delete content.
SHR-4160N/P USER’S MANUAL 10-35 Note Note Language change by SYSTEM LANGUAGE results in change of language expression setup of SHR-4160N/P . In short, the language setup of Smart V iewer does not change. Language specification to be supported is subject to change later .
10-36 Note Note If you fix Remote Control Device to the main body of SHR-4160N/P and activate the setting values, V iewer will be disabled to control PTZ. - Remocon (Remote Control Device) Remocon can set up Remote Control Device fixed to SHR-4160N/P .
SHR-4160N/P USER’S MANUAL 10-37 @ Camera - Config. Config. sets up Video, Audio On/Of f, Camera T itle, and Screen change T ime for each channel of on-line SHR-4160N/P . Note Note - The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not supplied to Title input.
10-38 - PTZ device If a dome camera is connected to all channels, sets up Camera ID, Protocol, Baud Rate, Parity , Data Bit, Stop Bit, and Serial Mode.
SHR-4160N/P USER’S MANUAL 10-39 - Event Rec. Event Rec. sets up Video Size, Quality , Rate, Pre Alarm, and Post Alarm values to be recorded when Event occurs. $ Recording - Rec. Mode Rec. Mode sets up Live Mode decision, Video Size during recording, Quality , and Rate.
10-40 - Alarm Rec. Alarm Rec. sets up the information necessary for Alarm Recording. - Motion Rec. Motion Rec. sets up the information necessary for recording by Motion Detection. Note Note At least one camera should be selected in advance to be coupled with Alarm.
SHR-4160N/P USER’S MANUAL 10-41 - Video Loss V ideo Loss sets up the information on how to inform the user of V ideo Loss of SHR-4160N/P . % Network - Password This sets up the password for Admin and User to let you connect with SHR-4160N/P through Network in Smart Viewer .
10-42 Note Note - The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not supplied to Network Password input. - Use the BACKSP ACE key to delete content. Note Note - Default Admin Password is set to 654321. - Default User Password is set to 654321.
SHR-4160N/P USER’S MANUAL 10-43 ● Callback - Sets up the Callback functions of SHR- 4160N/P . - Sets up the IP address and port to which SmartViewer was installed to deliver the Callback message in the event of Alarm, Motion Detection, or Video Loss.
10-44 Note Note - SHR-4160N/P uses 4 PORT s for TCP connection. - A PORT number is flexible and 4 numbers in a row will be changed in all. (554,555,556,557 ➝ 558,559,560,561) - Y ou shall allocate the above ports for SHR-4160N/P if you want to compose a net- work by IP Router .
SHR-4160N/P USER’S MANUAL 10-45 ● V ideo Recording ! Naming - Being connected to SHR-4160N/P in Monitoring or Search Mode, you can save the video data in display in .dvr file format. This determines how to name .dvr file format. - The file name depends on camera number and serial number , set to “Camera No.
10-46 ● Sequence T ime - As long as you are connected to SHR-4160N/P in Monitoring Mode while Screen change is dominant, this sets up Screen change T ime. The scope of setup ranges from 5 to 30seconds. ● OSD Display - Determines if OSD shall be displayed on each channel of Smart Viewer .
SHR-4160N/P USER’S MANUAL 10-47 Site Setup - Click the [Site Setup] button for Site Setup. - Site Setup sets up the information on DVR(SHR-4160N/P) or Site that you want to contact by Smart Viewer . - Smart Viewer allows you to contact DVR(SHR-4160N/P) or Site registered here.
10-48 ● DVR List - DVR List sets up the information on DVR(SHR-4160N/P) that you want to contact by Smart Viewer . - Y ou may register a new DVR(SHR-4160N/P) or delete and edit the DVR (SHR-4160N/P) selected from the registered list and the name and IP / MAC Address of the registered DVR will be enlisted in DVR List.
SHR-4160N/P USER’S MANUAL 10-49 ! Adding New DVR(SHR-4160N/P) - If you press the [New] button, the following window will pop up where you are able to add DVR(SHR-4160N/P) information. 1. Network Modes - LAN - If DVR(SHR-4160N/P) is connected to LAN, set Network Modes to LAN.
10-50 2. Network Modes - ADSL - If DVR(SHR-4160N/P) is connected to ADSL, set Network Modes to ADSL. - If the LAN connected to DVR(SHR-4160N/P) uses Static IP , select Static IP from Address T ype and input the name and IP Address of DVR(SHR-4160N/P).
SHR-4160N/P USER’S MANUAL 10-51 Note Note - DVR MAC Address is written in the side label of the product. It is also found in System Information of DVR Menu. - If DVR(SHR-4160N/P) is connected to ADSL, the network bandwidth is low . Therefore, the transmission speed becomes low and V iewer operates in the more limited range.
10-52 # Modification of Already-Registered DVR(SHR-4160N/P) - If you select one DVR(SHR-4160N/P) in DVR List for modification and press the [Modify] button, the following message box will pop up. If you press [OK] button then, DVR(SHR-4160N/P) will be modified.
SHR-4160N/P USER’S MANUAL 10-53 ● Site List - Site List registers multi- DVRs(SHR-4160N/P) that you want to contact at once by Smart Viewer at one site for control.
10-54 @ Deletion of Already-Registered Site or DVR(SHR-4160N/P) - If you select one Site or DVR(SHR-4160N/P) in Site List for deletion and press the [Delete] button, the following message box will pop up. If you press [OK] button then, either Site or DVR(SHR-4160N/P) will be deleted.
SHR-4160N/P USER’S MANUAL 10-55 - If you select one DVR(SHR-4160N/P) and press the [Modify] button, the following message box will pop up and modification to DVR(SHR-4160N/P) is prohibited. Modification to DVR(SHR-4160N/P) shall be done only in DVR List.
10-56 S/W V ersion - If you press the [S/W V ersion] button, Smart Viewer version, system requirements, and the version of DVR(SHR-4160N/P) System S/W , being connected to Smart V iewer , if ever will be displayed. - Y ou can upgrade the on-line DVR(SHR-4160N/P) System S/W remotely .
SHR-4160N/P USER’S MANUAL 10-57 ● Smart Viewer V ersion - Smart Viewer V ersion and system requirements will be displayed. ● DVR V ersion - DVR V ersion not only displays the connected DVR(SHR-4.
10-58 @ Click the following button to open the “SHR-4160N/P Firmware” file in tgz format. # Press the [Upgrade] button to transmit a file to the selected DVR(SHR- 4160N/P) and start upgrade of DVR(SHR-4160N/P) S/W . $ The progress of file transmission and upgrade will be displayed at the bottom.
Chapter 11 Backup V iewer 11.
1 Intr oduction 11-1 In SHR-4160N/P , you can back up the video data by using External HDD, USB Memory , and CD. In the Backup V iewer , the backup image data can be searched or played in the PC through the CD/DVD or connecting the external HDD, USB Memory to the user ’s PC.
2 Features 11-2 ■ The video data backed up in any method among External HDD, USB Memory , and CD can be searched or played in your PC. ■ Backup Viewer is optimized in the resolution of 1024 x 768.
SHR-4160N/P USER’S MANUAL 3 PC Specification(Recommendation) 11-3 ● OS: Windows 2000, Windows XP ● Recommendation : - CPU Pentium 3 1GHz or higher - RAM 256Mb or higher - VGA RAM 16Mb or higher - Direct X 8.
4 Backup V iewer Installation 11-4 ● Put the Smart Viewer Program CD in CD-ROM and open the "Backup V iewer" folder in the CD. ● Run the “Setup.
SHR-4160N/P USER’S MANUAL 11-5 ● Click "Next". ● If you agree with the Backup Viewer license, click "Y es"..
11-6 ● Select a folder to install Backup Viewer and click "Next". ● Install the execution file and set up the system as necessary ..
SHR-4160N/P USER’S MANUAL 11-7 ● Installation is complete. Click "Finish" to terminate the whole installation process..
5 Executing Backup V iewer Pr ogram 11-8 ● Double-click the Backup Viewer 1.0 icon in the background screen to execute the program..
SHR-4160N/P USER’S MANUAL 6 Initial Screen of Backup V iewer 11-9 ● Description ! T erminates or minimizes the program. @ Displays the current date, weekday , and time. # Selects a device(External HDD, USB Memory , or CD/DVD) for connection. $ Displays the image in play .
7 Using Backup V iewer 11-10 ● Connecting Connecting means you may access and search the video data recorded in External HDD, USB Memory , or CD/DVD installed in your PC. Select a device that you wish to connect and click the Connecting button. ● Connecting Screen ● Display of T ime - Displays the date, weekday , and time of your PC.
SHR-4160N/P USER’S MANUAL 11-11 ● Display of Connection - When connected to the device installed in your PC, the Connecting button indicates the connecting condition. - Click the Connecting button for disconnection. ● Display of Play Screen OSD ! Displays the CH number and replay time.
11-12 ● Calendar Window - The date when the video data was recorded in the current device is displayed in red. - Click the red colored date to display the video information in T imeline. - A thick red box will be displayed in the current date. - ¦ : Moves to the previous month.
SHR-4160N/P USER’S MANUAL 11-13 ● Play Buttons ! Play @ Reverse Play # Stop $ Fast Forward % Fast Backward ^ Step Forward : Forward by 1 second & Step Backward : Backward by 1 second * Go to Last : Plays the first image of T imeline. ( Go to First: Plays the recent(last) image of T imeline.
11-14 ● T imeline - Displays the time when the video image was recorded in the current device for the date selected from the Calendar window . - The General mode displays the information for 24 hours from 0 to 24 o’clock and the Zoom mode displays the time information every 2 hours.
SHR-4160N/P USER’S MANUAL 11-15 ● Next Button - Displays the next channel. Note Note Channel change is not available in the process of (Play/Reverse Play/Fast Forward/Fast Backward).
.
Appendix 12.
1 Pr oduct Specification 12-1 SHR-4160N/P USER’S MANUAL Item Specification Remark CPU 32bit RISC CPU Memory SDRAM : 128MByte Flash : 16 MByte Operation System Embedded OS Broadcasting NTSC System Input V oltage AC 1 10-220V(NTSC) / 100-230V(P AL) Power Comsumption 85 W att Max Composite 16 Channel - 1.
12-2 Item Specification Remark Compression Video : MPEG4 Audio : G.726 Resolution Quality Level Max Image Rate *ips (image V ery High per sec) CIF(C) High 352X240(NTSC) Standard /352X288(P AL) Low Res.
SHR-4160N/P USER’S MANUAL 12-3 Item Specification Remark Calendar Event - Normal, Panic, Schedule, Alarm, Motion, Search Mode V ideo Loss Date/T ime Go to First Go to Last Backup Data Resolution Decoding Performance Resolution & 1Ch 4Ch Play Back Performance CIF 15ips(NTSC)/12.
2 HDD Specifications 12-4 ● Internal A T A HDD/IEEE1394/USB HDD I/F External HDD Maker RPM Capactity Interface Model No 120 GB SV1203N 160 GB SV1604N 120 GB 4R120LO Maxtor 160 GB 4R160LO 250 GB 5A250JO W estern 120 GB WD1200LB Digital 160 GB WD1600LB CD-R CD-RW CD-R CD-RW DVD+R DVD-R DVD+RW ❉ DVD-RW is not supported.
SHR-4160N/P USER’S MANUAL 3 Outline Drawing 12-5.
4 Factor y Default 12-6 This restores the Network information and preset values in SHR-4160N/P to the original state at the time of factory shipment. Factory Default will be done if you; - Use System .
SHR-4160N/P USER’S MANUAL 12-7 Classification Detailed Items Factory Setup Duration Off Event Monitoring Date On OSD Display T ime On Monitoring Setup T itle On Status On Spot Out Channel CH1 Spot O.
12-8 5 SHR-4160N/P Smar t V iewer Play Frame Specification FRAME V iewer Screen VIDEO SIZE RA TE Split Mode Half D1(N) CIF (C) Nine-split 1 frame/sec 15 frame/sec Quad 15 frame/sec 15 frame/sec Single.
SHR-4160N/P USER’S MANUAL 12-9 FRAME V iewer Screen VIDEO SIZE RA TE Split Mode Half D1(N) CIF (C) Nine-split 1 frame/sec 15 frame/sec Quad 15 frame/sec 15 frame/sec Single 15 frame/sec 15 frame/sec.
6 Tr oubleshooting(F AQ) 12-10 1. The system power is dead and LED in front of the system does not operate at all. - Please check the power connection. - Check the power voltage. - If all your efforts like above end up with nothing, check or exchange the power supply .
SHR-4160N/P USER’S MANUAL 12-11 7. The channel button does not operate in Live. - If the current screen is Event Monitoring, the channel button does not operate. Then, press the Alarm button to terminate the current screen and select a channel. 8. The cursor cannot reach Start during Calendar Search.
12-12 13. Smart V iewer in operation is disconnected. - If you change time, network setup, HDD format, Default Setup, or HDD attach- ment or detachment for SHR-4160N/P DVR, the current Smart Viewer will be automatically disconnected. - Check network connection.
AB68-00499B Correct Disposal of This Product (W aste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
Ein wichtiger Punkt beim Kauf des Geräts Samsung SHR-4160P (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Samsung SHR-4160P noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Samsung SHR-4160P - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Samsung SHR-4160P reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Samsung SHR-4160P erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Samsung SHR-4160P besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Samsung SHR-4160P verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Samsung SHR-4160P. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Samsung SHR-4160P gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
