Benutzeranleitung / Produktwartung SCR-3000P des Produzenten Samsung
Zur Seite of 52
DIGIT AL VIDEO RECORDER DVR COMBO User ’ s Manual CLASS A (For Business) T o use this product safely , have to read “ Important Safety Introductions ”, and then be well aware of the contents.
iii ii DIGIT AL VIDEO RECORDER Impor tant Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
Contents iii v 1 2 3 1-1 1-2 1-3 1-7 1-8 1-9 2-1 2-2 2-3 2-4 3-1 3-3 4 4-1 4-6 4-7 4-10 4-14 4-15 4-17 iv iv v Important Safety Instructions Contents I. Summary 1. Introduction 2. Features 3. Name and Function of Each Part 4. Introduction to the Remote Control 5.
1 I. Summar y.
1-2 1-1 DIGIT AL VIDEO RECORDER 1 Intr oduction 2 Features DVR COMBO is DVR system using both hard disk drive and VCR tape simultaneous- ly . Record TV reception into hard disk drive while also recording only desired program to VCR tape. Recorded VCR tape can be viewed with residential VCR.
1-3 1-4 DIGIT AL VIDEO RECORDER 3 Name and Function of Each Par t Front View POWER ALARM LAN CHECK REC VCR SEARCH MENU REC LOCK ARCHIVE 1 2 3 4 8 5 9 7 10 11 12 13 14 15 16 17 18 6 No Name Function SE.
1-6 1-5 DIGIT AL VIDEO RECORDER Back View 1 2 3 4 5 No Name Function Audio In/Out LAN External Input/Output Ports RCA type audio input/output connectors. Connector for LAN cable connection. ● ALARM IN: In N.C. (Normally Closed) mode, the system rec ognizes an alarm condition when a high (5V) signal is input for longer than 0.
Caution Caution The above items are subject to change without prior notice to improve product performance or functionality . 1-7 1-8 DIGIT AL VIDEO RECORDER 5 Checking the Package Contents 4 Intr oduction to the Remote Contr ol When purchasing product, first remove packing and put it on a flat floor or at a place to use it.
1-10 1-9 DIGIT AL VIDEO RECORDER 6 Attaching/Detaching HDD Caution Caution Be sure to lock the hard drive rack in place for normal operation of the system. Unless the hard drive rack is locked, the system cannot recognize your hard drive. When removing the hard drive rack, be sure to wait until your hard drive's power LED goes off.
II. Connection with Other Devices 2.
2-2 2-1 1 Connection to External Devices 2 Connection with Multiplexer (e.g. connection to SDM-160) DIGIT AL VIDEO RECORDER ■ This unit can be connected to external devices such as a camera for video signal input, a microphone for audio signal input, and an NTSC or P AL monitor for video and audio signal output.
2-3 2-4 DIGIT AL VIDEO RECORDER 3 System Connection for Alarm Recording 4 Connection with PC for Use <Rear Side Connection T erminal of DVR COMBO> <Outside Product> ALARM IN ALARM RESET AL.
2-6 2-5 DIGIT AL VIDEO RECORDER Connection with RS-485 If you control cameras, remote control is allowed through connection with RS-485 (up to 1.2km). A.
III. Basic Method to use 3.
3-2 3-1 DIGIT AL VIDEO RECORDER 1 Booting the System Power On There is a power switch on the upper right hand side behind the system. Pull the power switch up to boot the system. Then, the POWER LED ( ) on front of the system is turned on, a blue screen with the following message will appear and the system is booted.
The upper pointer shows the relative location of the recorded data being stored inside the hard disk and the lower pointer shows the relative location of the data currently being played back. The following pointer will be hidden in the general live screen and recording screen.
If system is in the recording state icon will blink. However , it does not blink in the Live Screen state. Indicates whether a HDD is installed or whether the hard drive rack is locked. It shows the relative location of the recorded data inside the hard disk.
3-7 DIGIT AL VIDEO RECORDER Playback screen Viewing The normal Playback screen looks like this. The upper pointer shows the relative location of the recorded data being stored inside the hard disk and the lower pointer shows the relative location of the data currently being played back.
IV . DVR Menus 4.
4-1 4-2 Changing the Settings ① Use the UP( ) and DOWN( ❷ ) buttons to select the setting you want to change. ➁ Press the ENTER( ) button to accept the choice. ➂ Use the UP( ) and DOWN( ❷ ) buttons to change the value. ➃ Press the ENTER( ) button to accept the choice.
4-4 4-3 DIGIT AL VIDEO RECORDER ➃ Similarly , press the UP( ) or DOWN( ❷ ) button so current minute is displayed. Then if pressing the LEFT( ➛ ) or RIGHT( ❿ ) button, the cursor is changed so hour or second is changed.
4-6 4-5 DIGIT AL VIDEO RECORDER 2 Setting of Date, Time and Screen The following illustrates the intial setting of the CLOCK/DISPLA Y MODE SETUP menu. ① DA TE Set the current date. ② TIME T ime can be entered in the form of 24 hours. ➂ DA TE DISPLA Y TYPE There are 3 date forms to be displayed.
4-8 4-7 DIGIT AL VIDEO RECORDER 3 Record Setup The following illustrates the intial setting of the RECORD MODE SETUP menu. ① DVR INPUT Set the 3 types of V ideo Input signals going into the DVR.VIDEO-IN is the input signal going into the BNC V ideo Jack, S-VIDEO is the signal going into the S-VHS Jack, and VCR PB is the VCR playback signal.
4-10 4-9 DIGIT AL VIDEO RECORDER 4 Alarm Record Setup The following illustrates the intial setting of the ALARM RECORD SETUP menu. ① ALARM SIGNAL DETECTION Y ou shall select ON to start recording in the event of alarming and select OFF to prevent recording in the event of alarming.
4-12 4-11 DIGIT AL VIDEO RECORDER ⑧ MOTION DETECTION The DVR will start recording images whenever it detects any movement only when ALARM SIGNAL DETECTION is set to ON . At this time, you can set the detailed items about the motion detection in the SET AREA & SENSITIVITY menu.
4-14 4-13 DIGIT AL VIDEO RECORDER 5 Reser vation Timer Setup The following illustrates the intial setting of the TIMER RECORD SETUP menu. ● T imer recording enables the system to automatically record when you are not present so that the recording is performed on the desired day at the desired time with the desired field rate.
4-16 4-15 DIGIT AL VIDEO RECORDER 6 The following illustrates the intial setting of the SYSTEM SETUP menu. ① P ASSWORD Set the system password. Y ou can enter a 4-digit number and the initial set value is 0000.
V . V iewing the VCR Menu 5 4-17 DIGIT AL VIDEO RECORDER 7 Communication Setup The following illustrates the intial setting of the COMMUNICA TION SETUP menu.
5-1 5-2 DIGIT AL VIDEO RECORDER 1 VCR Menus Entering the VCR MAIN MENU Press the VCR ( ) button once. Then the VCR LED will light up. Now press the MENU ( ) button.
5-4 5-3 DIGIT AL VIDEO RECORDER 2 MANUAL ARCHIVE The following illustration shows the initial settings of the MANUAL ARCHIVE menu. MANUAL ARCHIVE FROM RECORD EVENT LIST FROM ALARM EVENT LIST FROM MOTI.
5-6 5-5 DIGIT AL VIDEO RECORDER (2) FROM ALARM EVENT LIST FROM ALARM EVENT LIST allows you to back up the video and audio data that has been recorded on the hard drive at the time of an event, which is triggered by alarm input or motion detection, onto a video tape.
5-8 5-7 DIGIT AL VIDEO RECORDER (4) TIME RANGE From the MANUAL ARCHIVE menu, select "TIME RANGE" and the following screen appears. In the TIME RANGE ARCHIVE screen, you can set the start and end times of a particular section of the video and audio that you want to back up from the hard drive.
5-10 5-9 DIGIT AL VIDEO RECORDER 3 TIMER ARCHIVE The following illustration shows the initial settings of the TIMER ARCHIVE menu. The T imer Backup function allows you to set the system to automatically back up the data that is recorded on the HDD to a video tape while you are away from the system.
5-12 5-11 DIGIT AL VIDEO RECORDER (3) T APE SELECT Set the tape length for accurate calculation of remaining tape time and precise control. ● SCR-3000N/SSC-Dual [T -120/T -160/T180] ● SCR-3000P [E-180/E-210/E-260] (4) VCR BUZZER Set the buzzer so that the VCR's status could be known.
5-13 DIGIT AL VIDEO RECORDER The ARCHIVE CHECK function allows you to check whether the images played back on the DVR and transferred to the VCR are recorded correctly . The DVR plays back the signals to be Archived for 5 seconds and send them to the VCR and the VCR records them.
VI. Record 6.
6-2 6-1 DIGIT AL VIDEO RECORDER 1 Basic Record Basic Record ① CURRENT IMAGE RECORD Press the RECORD( ) button to record current image. If doing so, the light of the RECORD( ) button turns on and record starts while following message appears on the screen.
6-3 6-4 DIGIT AL VIDEO RECORDER 2 Record Lock 3 Alarm Record Record Lock Press the REC LOCK ( ) button during recording to lock the recording. Then, the REC LOCK ( ) button will light up. At this time, pressing the STOP ( ) button will not stop the recording.
VII. Retrieval and Playback 7 6-5 DIGIT AL VIDEO RECORDER 4 Reser vation Record Reservation Record Setup Y ou can enter the day , time, and field rate for the timer recording in the TIMER RECORD SETUP menu so that the recording will be made on the set day for the set amount of time.
7-2 7-1 DIGIT AL VIDEO RECORDER 1 Search Menus Entering the DVR SEARCH MENU T o search the recorded data, press the SEARCH ( ) button. Then the following screen should appear . Selecting a Menu Item Use the UP( ) or DOWN( ❷ ) buttons to move to the menu item you want.
7-3 7-4 DIGIT AL VIDEO RECORDER 2 Retrieval by Date and Time Enter the date and time you want to search, place the cursor at SEARCH ST AR T , and then press the ENTER ( ) button. The following screen will appear and the system will start the data search.
7-5 7-6 DIGIT AL VIDEO RECORDER 4 Alarm Record Retrieval Among the data on the HDD, the ones that were recorded when an alarm was triggered will be displayed as a list based on the recording start time. Other information is same as in “3. Recorded Data List V iew” on p.
7-7 7-8 DIGIT AL VIDEO RECORDER 6 PB CHANNEL SETUP When recording in conjunction with a multiplexer , you can show or hide the playback of a par- ticular channel. Set the channel to ON to show it or set the channel to OFF to hide it. 7 SYSTEM INDICA TION The following screen appears when you select SYSTEM INDICA TION.
7-9 7-10 DIGIT AL VIDEO RECORDER (2) SYSTEM INFORMA TION The following illustration shows the initial settings of the SYSTEM INFORMA TION menu. It displays the basic system information.
7-12 7-11 DIGIT AL VIDEO RECORDER 8 Basic Playback T o immediately play back the data recorded on the HDD, press the PLA Y/STILL( ❿ II ) button. The following screen will appear and the beginning of the recorded data will be played back in turn. T o stop playback, press the STOP ( ) button.
7-13 7-14 DIGIT AL VIDEO RECORDER 9 VCR Playback T ake following steps to play recorded videotape. Insert the videotape into deck. T urn VCR LED by pressing VCR button ( ) once. Then press PLA Y/STILL( ❿ II ) button. Press STOP ( ) button to stop play .
7-15 DIGIT AL VIDEO RECORDER 11 Playing Back a Section Repeatedly The REPEA T function allows you to repeatedly play back a certain section during DVR or VCR playback.
VIII. Others 8.
8-2 8-1 1 Pr oduct Standards Rated V oltage NTSC (AC 1 10 ~ 240V , 60 Hz), P AL (AC 220V , 50Hz) Power Consumption 34W HDD Removable HDD 80GB BACKUP VCR VIDEO T APE V ideo Input Composite V ideo, BNC Jack - 1CH (1.0 Vp-p, 75 Ω ) S-VHS VIDEO V ideo Output Composite V ideo, BNC Jack - 1CH (1.
Appendix 9.
9-2 9-1 1 Check Points before Call Ser vice Center DIGIT AL VIDEO RECORDER If the system malfunctions, please check the following instruction before you call the service center or the shop where you bought the system. T rouble Check Points • Unable to supply power .
www .securitysamsung.com AB68-00406A Printed in Korea 9-3 DIGIT AL VIDEO RECORDER 2 Q & A Question Answer • Does recording continues after power cut during recording.
Ein wichtiger Punkt beim Kauf des Geräts Samsung SCR-3000P (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Samsung SCR-3000P noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Samsung SCR-3000P - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Samsung SCR-3000P reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Samsung SCR-3000P erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Samsung SCR-3000P besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Samsung SCR-3000P verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Samsung SCR-3000P. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Samsung SCR-3000P gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
