Benutzeranleitung / Produktwartung TS1340 des Produzenten Ryobi
Zur Seite of 28
OPERA T OR'S MANUAL 10 in. (254 mm) Compound Miter Saw Model TS1340 - Double Insulated Your new Miter Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
Page 2 TABLE OF CONTENTS PRODUCT SPECIFICA TIONS Blade Arbor 5/8 in. (16 mm) Blade Diameter 10 in. (254 mm) Rating 120 volts, 60Hz, AC Only No Load Speed 5000 RPM Input 1 4 Amperes Net Weight 29.92 lbs. (13.6 kg.) INTRODUCTION Y our saw has many features for making cutting operations more pleasant and enjoyable.
Page 3 RULES FOR SAFE OPERA TION DOUBLE INSULA TION Double insulation is a concept in safety , in electric power tools, which eliminates the need for the usual three-wire ground power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation.
Page 4 Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your miter saw works. READ ALL INSTRUCTIONS ■ KNOW YOUR POWER TOOL.
Page 5 ■ NEVER reach behind, under, or within three inches of the blade and its cutting path with your hands and fingers for any reason. ■ NEVER hand hold a workpiece that is too small to be clamped.
Page 6 SA VE THESE INSTRUCTIONS RULES FOR SAFE OPERA TION ■ STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired.
Page 7 UNP ACKING ■ Lift the saw arm by the handle. Hand pressure should remain on the saw arm to prevent sudden rise upon release of the tie wrap. ■ Examine all parts to make sure no breakage or damage has occurred during shipping.
Page 8 The following items are included with your Compound Miter Saw: ■ 10 in. (254 mm) Saw Blade ■ Miter Lock Handle ■ Dust Bag ■ Dust Guide LOOSE P ARTS LIST ■ Work Clamp ■ Blade Wrench ■ Operator's Manual ■ Warranty Registration Card Fig.
Page 9 FEA TURES KNOW YOUR COMPOUND MITER SAW See Figure 2. Before attempting to use your saw, familiarize yourself with all operating Features and Rules for Safe Operation. W ARNING: Do not allow familiarity with your saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury.
Page 10 FEA TURES BLADE WRENCH / ST ORAGE AREA See Figure 2. A blade wrench is packed with your saw . One end of the wrench is a phillips screwdriver and the other end is a 1/4 in. (6.4 mm) hex key . Use the hex key end when installing or removing blade and the phillips end when removing or loosening screws.
Page 11 15 30 45 0 15 30 45 FEA TURES POSITIVE STOPS ON MITER TABLE Positive stops have been provided at 0 ° , 15 ° , 22-1/2 ° , 30 ° , and 45 ° . The 22-1/2 ° and 45 ° positive stops have been provided on both the left and right side of the miter table.
Page 12 ASSEMBL Y W ARNING: To prevent accidental starting that could cause possible serious personal injury, assemble all parts, make sure all adjustments are complete, and make sure all fasteners are secure before connecting saw to power supply.
Page 13.
Page 14 1 5 45 30 45 30 3 1.6 31.6 5 1 22.5 ASSEMBL Y CAUTION: Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard.
Page 15 ADJUSTMENTS W ARNING : Failure to unplug your saw could result in accidental starting causing possible serious personal injury. ■ Push down on the saw arm and pull out the lock pin to release the saw arm. ■ Raise saw arm to its full raised position.
Page 16.
Page 17.
Page 18 ADJUSTMENTS BEVEL PIVOT ADJUSTMENT ■ Your compound miter saw should bevel easily by loos- ening the bevel lock knob and tilting the saw arm to the left. ■ If movement is tight or if there is play in the pivot, have saw repaired by at your nearest RYOBI AUTHORIZED SERVICE CENTER.
Page 19 CUTTING WITH YOUR COMPOUND MITER SAW W ARNING: When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece.
Page 20 BEVEL SCALE INDICATOR SCREW SCALE INDICATOR OPERA TION ■ Pull out the lock pin and lift saw arm to its full height. ■ Loosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen. ■ Press the miter lock plate down with your thumb and hold.
Page 21 OPERA TION ■ Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. See Figure 27. W ARNING: To avoid serious personal injury, always keep your hands outside the no hands zone; at least 3 in.
Page 22 ■ Recheck miter angle setting. Make a test cut in scrap material. ■ Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board could collapse on the blade at the end of the cut, jamming the blade.
Page 23 CUTTING COMPOUND MITERS To aid in making the correct settings, the compound angle setting chart below has been provided. Since compound cuts are the most difficult to accurately obtain, trial cuts should be made in scrap material, and much thought and planning made, prior to making your required cut.
Page 24 When setting the bevel and miter angles for compound miters, remember that the settings are interdependent; chang- ing one angle changes the other angle as well. Keep in mind that the angles for crown moldings are very precise and difficult to set.
Page 25.
Page 26 W ARNING: When servicing, use only identical Ryobi replacement parts. Use of any other part may create a hazard or cause product damage. GENERAL Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use.
Page 27 NOTES.
Page 28 983000-248 3-03 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson SC 29625 Post Office Box 1207 Anderson SC 29622-1207 Phone 1-800-525-2579 www.
Ein wichtiger Punkt beim Kauf des Geräts Ryobi TS1340 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ryobi TS1340 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ryobi TS1340 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ryobi TS1340 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ryobi TS1340 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ryobi TS1340 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ryobi TS1340 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ryobi TS1340. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ryobi TS1340 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
