Benutzeranleitung / Produktwartung Table Saw des Produzenten Ryobi
Zur Seite of 34
OPERA T OR'S MANUAL 10 in. (254 mm) T ABLE SA W BTS20R SA VE THIS MANUAL FOR FUTURE REFERENCE Your new Table Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
Page 2 Product Specifications .............................................. 2 Rules for Safe Operation ........................................ 3-6 Electrical ...............................
Page 3 IMPORTANT Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the tool to your nearest Ryobi AUTHORIZED SERVICE CENTER for repair. When servic- ing, use only identical Ryobi replacement parts.
Page 4 Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your table saw works. READ ALL INSTRUCTIONS KNOW YOUR POWER TOOL.
Page 5 BLADES COAST AFTER TURN OFF. NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. INSPECT TOOL CORDS PERIODICALLY. If damaged, have repaired by a qualified service technician at an authorized service facility.
Page 6 CHECK WITH A QUALIFIED ELECTRICIAN or service personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool is properly grounded.
Page 7 ELECTRICAL ELECTRICAL CONNECTION Your Ryobi Table Saw is powered by a precision built electric motor. It should be connected to a power supply that is 120 volts, 60Hz, AC only (normal household current). Do not operate this tool on direct current (DC).
Page 8 Anti-Kickback Pawls (Fingers) Device which, when properly installed and maintained, is designed to stop the workpiece from being kicked back toward the front of the saw during a ripping operation. Arbor The shaft on which a blade or cutting tool is mounted.
Page 9 The saw is factory set for accurate cutting. After assem- bling it, check for accuracy. If shipping has influenced the settings, refer to specific procedures explained in the opera- tion and maintenance sections of this manual.
Page 10 5 Fig. 3 Key No. Description Qty. 1 Rip Fence ..................................................................................................................... .................................... 1 2 Miter Gauge ..........................
Page 11 GETTING TO KNOW YOUR SAW Your saw is designed to perform as a versatile, accurate, precision cutting tool that is easy to operate. It is equipped with the following features for convenience, e.
Page 12 Fig. 5 SWITCH KEY FEA TURES W ARNING: Although some of the illustrations in this manual are shown with the blade guard removed for clarity, do not operate the saw without the blade guard unless specifically instructed to do so.
Page 13 BLADES It is recommended that you use a RYOBI 10 in. (254 mm) Combination Blade, which is provided with the BTS20 R Table Saw. You will get maximum performance with the following features: • 36 precision ground, micro-grain carbide teeth • kerf width of 2.
Page 14 ASSEMBL Y Remove the table saw base, loose parts, and hardware from the packing materials. Check all items with the loose parts list and drawing. If you are unsure about the description of any part, refer to the drawing. If any parts are missing, delay assembling until you have obtained the missing part(s).
Page 15 ASSEMBL Y OPENING THE LEG STAND See Figure 10. Note: You can also refer to the blue label on the right-hand side of the table saw for setup procedures. Standing to the side of the table saw, use your left hand to pull the leg stand latch towards you.
Page 16 ASSEMBL Y CLOSING THE LEG STAND See Figure 11. Note: You can also refer to the blue label on the top of the table saw for tear-down procedures. Standing to the side of the table saw, grasp the table tilt handle with your left hand. Tilt the table saw to the your left and grab the grip with your right hand.
Page 17 TO INSTALL RIP FENCE See Figure 12. To install the rip fence, place the rear lip on the rear rail and pull slightly toward the front of the unit. Lower front end onto the guide surfaces on top of the front rail. Check for a smooth gliding action.
Page 18 BLADE AND GUARD ASSEMBL Y W ARNING: Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious injury. TO CHECK SAW BLADE INSTALLATION To check the saw blade, first remove the screw holding the throat plate in place.
Page 19 ASSEMBL Y Blade alignment with the riving knife can be adjusted for different blade thickness. Refer to Settings and Adjustments in the Operations Section. Before continuing, read To Check, Replace or Adjust the Blade Guard Assembly on page 23 to make sure of proper riving knife alignment.
Page 20 OPERA TION Fig. 18 PUSHBLOCKS PUSHSTICKS Use the right type of blade for the cut being made. Use the blade guard assembly for all through cuts. CUTTING AIDS See Figure 18. Pushsticks are devices used for safely pushing a workpiece through the blade instead of using your hands.
Page 21 OPERA TION The kerf (the cut made by the blade in the wood) will be wider than the blade to avoid overheating or binding. Make allowance for the kerf when measuring wood. Make sure the kerf is made on the waste side of the measuring line.
Page 22 OPERA TION SETTINGS AND ADJUSTMENTS TO REMOVE THE BLADE See Figures 20 - 22. Use the two wrenches supplied with the saw in this proce- dure to replace the blade. W ARNING: Unplug your saw and make sure the blade guard assembly is installed and working properly to avoid serious personal injury.
Page 23 OPERA TION TO CHECK, REPLACE OR ADJUST THE BLADE GUARD ASSEMBLY See Figures 23 - 24. The riving knife is mounted between several shims that can be relocated as needed to center the knife behind the blade. It is held in place by two bolts and hex nuts at its base.
Page 24 30 45 0 GULLET Fig. 27 FRONT RAIL Fig. 25 BEVEL INDICATOR BEVEL LOCKING LEVER BEVEL HANDLE Fig. 26 2 in. LOCKING HANDLE BLADE RIP FENCE 2 IN. MARK SCALE SCALE INDICATOR TO ADJUST THE BLADE DEPTH The blade depth should be set so that the outer points of the blade are higher than the workpiece by approximately 1/8 in.
Page 25 OPERA TION HEELING (PARALLELING) THE BLADE TO THE MITER GAGE GROOVE See Figures 28 - 30 . W ARNING: Make sure the switch is off, switch key is removed, and saw is unplugged. Failure to do so could result in accidental starting causing serious personal injury.
Page 26 19 20 21 22 23 24 25 26 27 21 22 23 24 25 OPERA TION Fig. 31 TO USE OUTFEED SUPPORT See Figure 31. The outfeed support slides to give the operator additional support for cutting long workpieces. With the table saw in the off position, stand behind the saw.
Page 27 + - + - OPERA TION Set the miter gauge to 0˚ and tighten the lock knob. Place a support (the same height as saw table) behind the saw for the cut work. Make sure the wood is clear of the blade before turning on the saw. To turn the saw on ( ), lift the switch button.
Page 28 + - + - OPERA TION TO MAKE A BEVEL CROSS CUT See Figure 37. It is recommended that you place the piece to be saved on the left side of the blade and that you make a test cut on scrap wood. W ARNING: Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.
Page 29 + - OPERA TION TO MAKE A COMPOUND MITER CUT It is recommended that you place the piece to be saved on the left side of the blade and that you make a test cut on scrap wood first. W ARNING: Make sure the blade guard assembly is securely installed and working properly to avoid serious personal injury .
Page 30 OPERA TION W ARNING: Never feed wood with your hands when making any non- through cut such as rabbets or dadoes. W ARNING: When making a non-through cut, the cutter is covered by the workpiece during most of the cut. Be alert to the exposed cutter at the start and finish of every cut to avoid the risk of serious personal injury.
Page 31 + - W ARNING: Before performing any adjustment, make sure the tool is unplugged from the power supply and the switch is in the off ( ) position. Failure to head this warning could result in serious personal injury. TO SET BLADE AT 0 ° OR 45 ° See Figure 40.
Page 32 1. Blade is out of balance. 2. Blade is warped or damaged. 3. Saw is not mounted securely to a level work surface. 1. Rip fence not mounted correctly. 2. Rails are dirty or sticky. 3. Adjustment nut needs adjusting. 1. Blade is dull. 2. Work is fed too fast.
Page 33 NOTES NOTES.
Page 34 983000-428 3 -04 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson, SC 29625 Post Office Box 1207 Anderson SC 29622-1207 Phone 1-800-525-2579 www.
Ein wichtiger Punkt beim Kauf des Geräts Ryobi Table Saw (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ryobi Table Saw noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ryobi Table Saw - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ryobi Table Saw reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ryobi Table Saw erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ryobi Table Saw besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ryobi Table Saw verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ryobi Table Saw. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ryobi Table Saw gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
