Benutzeranleitung / Produktwartung RY6202 des Produzenten Ryobi
Zur Seite of 20
OPERA T OR'S MANUAL 5-1/2 in. (140 mm), 14.4 VOL T CORDLESS CIRCULAR SA W MODEL NO. R Y6202 SA VE THIS MANUAL FOR FUTURE REFERENCE SPECIFICA TIONS: Blade Diameter 5-1/2 in. (140 mm) Blade Arbor 3/8 in. (10 mm) Cutting Depth at 0 ° 1-9/16 in. (40 mm) Cutting Depth at 45 ° 1-1/8 in.
Page 2 Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved. The following recommended accessories are current and were available at the time this manual was printed.
Page 3 W ARNING: Read and follow all instructions. Failure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury . SA VE THESE INSTRUCTIONS W ork Area ■ Keep your work area clean and well lit. Cluttered benches and dark areas invite accident.
Page 4 Additional Rules For Safe Operation ■ Know your power tool. Read operator ’ s manual care- fully . Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury .
Page 5 SPECIFIC SAFETY RULES Additional Specific Safety Rules Continued ■ Never use damaged or incorrect blade washers or bolts. The blade washers and bolt were specially de- signed for your saw , for optimum performance and safety of operation.
Page 6 ■ To reduce the risk of damage to charger body and cord, pull by charger plug rather than cord when disconnecting charger . Following this rule will reduce the risk of serious personal injury . ■ Make sure cord is located to that it will not be stepped on, tripped over , or otherwise subjected to damage or stress.
Page 7 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
Page 8 KNOW YOUR CORDLESS CIRCULAR SAW See Figure 1. Before attempting to use any tool, familiarize yourself with all operating features and safety requirements. Features include easily operated bevel cut and depth of cut adjustment mechanisms; positive 0 ° bevel stop; spindle lock; and blade wrench storage.
Page 9 Fig. 2 IMPORTANT CHARGER INFORMATION The battery pack for this Circular Saw, should be charged only with charger provided. The charger part number will be found on a plate located on the bottom of the charger. Before using the charger, it is extremely important that you familarize yourself with the LED functions of the charger.
Page 10 45 45 50 50 3 0 30 22 22 1 1 2 3 0 45 W ARNING: Always remove battery pack from your saw when you are assembling parts, making adjustments, assembling or removing blades, cleaning, or when not in use. Re- moving battery pack will prevent accidental starting that could cause serious personal injury .
Page 11 45 4 5 50 5 0 30 30 22 22 1 1 2 3 0 45 Fig. 6 BLADE SCREW BLADE WRENCH SPINDLE LOCK BUTTON ■ Fit saw blade inside lower blade guard and onto spindle. NOTE: The saw teeth point upward at the front of saw as shown in figure 5. ■ Replace outer blade washer .
Page 12 KICKBACK See Figure 8. The best guard against kickback is to avoid dangerous practices. Kickback occurs when the blade stalls rapidly and the saw is driven back towards you. Blade stalling is caused by any action which pinches the blade in the wood.
Page 13 ■ When making a cut use steady, even pressure. Never force cuts. ■ Do not cut warped or wet lumber. ■ Always hold your saw firmly with both hands and keep your body in a balanced position so as to resist the forces of kickback should it occur.
Page 14 TO HELP MAINTAIN CONTROL: ■ Always support your workpiece near the cut. ■ Support your workpiece so the cut will be on your left. ■ Clamp your workpiece so it will not move during the cut. Place your workpiece with its good side down. NOTE: The good side is the side on which appearance is important.
Page 15 TO CROSS CUT OR RIP CUT When making a cross cut or rip cut, align your line of cut with the outer blade guide notch on the saw base as shown in figure 17. Since blade thicknesses vary, always make a trial cut in scrap material along a guideline to determine how much, if any, the guideline must be offset to produce an accurate cut.
Page 16 TO BEVEL CUT The angle of cut of your saw may be adjusted to any desired setting between zero and 50 ° . NOTE: When making cuts at 50 ° , blade should be set at full depth of cut. When making 45 ° bevel cuts, there is a notch in the saw base to help you line up the blade with the line of cut.
Page 17 1 2 45 0 0 15 22 30 45 50 45 4 5 50 5 0 30 30 22 22 POSITIVE 0 ° BEVEL STOP See Figure 21. Your saw has a positive 0 ° bevel stop, that has been factory adjusted to assure 0 ° angle of your saw blade when making 90 ° cuts. However, misalignment can occur during shipping.
Page 18 45 45 50 50 30 30 22 22 TO RIP CUT OPTIONAL RIP GUIDE (EDGE GUIDE) See Figure 23. Use a guide when making long or wide rip cuts with your saw. An optional rip guide with a five inch scale is available or you can make an efficient rip guide by clamping a straight edge to your workpiece.
Page 19 W ARNING: When servicing, use only identical replacement parts. Use of any other part may create a hazard or cause product damage. W ARNING: Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc. come in contact with plastic parts.
983000-191 9 -03 • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center.
Ein wichtiger Punkt beim Kauf des Geräts Ryobi RY6202 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ryobi RY6202 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ryobi RY6202 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ryobi RY6202 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ryobi RY6202 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ryobi RY6202 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ryobi RY6202 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ryobi RY6202. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ryobi RY6202 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
