Benutzeranleitung / Produktwartung RCT2800AD des Produzenten Ryobi
Zur Seite of 16
2-Cycle Petr ol T rimmer OPERA TOR’S MANUAL IMPORT ANT MANUAL DO NOT THROW AW A Y RCT2800AD.
2 INTRODUCTION Read the Operator’ s Manual(s) and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders. W ARNING! RULES FOR SAFE OPERA TION DANGER : Failure to obey a safety warning will result in serious injury to yourself or to others.
3 READ ALL INSTRUCTIONS BEFORE OPERA TING • Read the instructions carefully. Be familiar with the controls and proper use of the unit. • Do not operate this unit when tired, ill or under the influence of alcohol, drugs or medication. • Children under the age of 15 must not use the unit; teens may operate the unit with adult guidance.
4 SYMBOL MEANING • SAFETY ALERT SYMBOL Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs. • WARNING - READ OPERATOR'S MANUAL Read the Operator’s Manual(s) and follow all warnings and safety instructions.
5 RULES FOR SAFE OPERA TION APPLICA TIONS As a trimmer: • Cutting grass and light weeds • Edging • Decorative trimming around trees, fences, etc.
6 ASSEMBL Y INSTRUCTIONS Fig. 2 INST ALL THE CUTTING A TT ACHMENT SHIELD Use the following instructions if the cutting attachment shield on your unit is not installed. 1. Place the cutting attachment shield onto the shaft housing. Be sure the guard mounting bracket slides into the slot on the edge of the cutting shield.
7 OIL AND PETROL INFORMA TION NOTE: Dispose of the old petrol/oil mix in accordance to Federal, State and Local regulations. CAUTION: For proper engine operation and maximum reliability , pay strict attention to the oil and petrol mixing instructions on the 2-cycle oil container .
8 ST ARTING INSTRUCTIONS 1. Mix petrol with oil. Fill petrol tank with petrol/oil mixture. Refer to Oil and Petrol Mixing Instructions . 2. Fully press and release the primer bulb 10 times, slowly. Some amount of petrol should be visible in the primer bulb and petrol lines (Fig.
9 OPERA TING INSTRUCTIONS NOTE: Do not rest the Bump Head™ on the ground while the unit is running. Some line breakage will occur from: • Entanglement with foreign matter • Normal line fatigue .
10 MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up.
11 MAINTENANCE AND REP AIR INSTRUCTIONS Fig. 19 Fig. 15 NOTE: SplitLine™ can only be used with the inner reel with the slotted holes. Single line can be used on either type of inner reel. Use Figure 15 to identify the inner reel you have. NOTE: Always use the correct line length when installing trimming line on the unit.
12 MAINTENANCE AND REP AIR INSTRUCTIONS AIR FIL TER MAINTENANCE Removing the Air Filter/Muffler Cover 1. Place the choke lever in Position 2. NOTE: The choke lever must be in Position 2 to remove the air filter/ muffler cover. 2. Remove the four (4) screws securing the air filter/muffler cover (Fig.
13 SP ARK ARRESTOR MAINTENANCE 1. Remove air filter/muffler cover. Refer to Removing the Air Filter/Muffler Cover . 2. Locate muffler front and the two (2) bolts securing it to the engine (Fig. 26). Remove the two (2) bolts using a flatblade screwdriver or 5/16-inch socket or nut driver.
14 CLEANING Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle. Wipe off any moisture with a soft cloth.
15 If further assistance is requir ed, contact your authorized service dealer . CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of .
SPECIFICA TIONS ENGINE* DRIVE SHAFT and CUTTING A TT ACHMENT* *All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. Engine Type..............
Ein wichtiger Punkt beim Kauf des Geräts Ryobi RCT2800AD (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ryobi RCT2800AD noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ryobi RCT2800AD - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ryobi RCT2800AD reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ryobi RCT2800AD erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ryobi RCT2800AD besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ryobi RCT2800AD verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ryobi RCT2800AD. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ryobi RCT2800AD gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.