Benutzeranleitung / Produktwartung 227 L, 227 LD, 232 L, 240 L des Produzenten Ryobi
Zur Seite of 33
227L/LD 232L 240L Operator's manual Read through the Operator‘s manual carefully and understand the content before using the machine. 101 91 66-26.
2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine.
English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal pr otective equipment .
4 – English The machine ‘ s saf ety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “What is what“ to locate where this equipment is positioned on your machine.
English – 5 SAFETY INSTR UCTIONS 4. Vibration damping system Y our machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. U se of incorrectly wound cord or incorr ect cutting equipment increases the level of vibration.
6 – English 3. Cutting attachment guard • Ensure that the spray guard is undamaged and is not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" .
English – 7 SAFETY INSTR UCTIONS 6. Cutting equipment The section describes how through corr ect maintenance and through using the right type of cutting equipment you can: • Obtain maximum clearing capacity. • Increase the service life of the cutting equipment.
8 – English SAFETY INSTR UCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like.
English – 9 ! General w orking instructions SAFETY INSTR UCTIONS Basic working techniques • Always drop to idling speed after each working operation. Longer periods running at full throttle without loading the engine (that is without resistance, which the engine feels from the cutting equipment when trimming) can lead to serious engine damage.
10 – English SAFETY INSTR UCTIONS Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. NOTE! This technique increases the wear on the cord.
English – 11 WHA T IS WHA T? What is what on the trimmer? 1. T rimmer head 2. Gr ease filler cap 3. Angle gear 4. Spray guar d 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. S uspension for harness 11. C ylinder cov er 12.
12 – English ASSEMBL Y Assembling the loop handlebar • Unscrew the handle and plastic cover from the handlebar bracket. • Place the loop handlebar with the handlebar holder on the handlebar bracket. Fit the handle and plastic cover. Do not tighten too tight.
English – 13 ASSEMBL Y Assembling: • Make sure the handle is loose. • Guide the cut-out on the lower section of the shaft into the coupling ‘ s locking plate on the upper section of the shaft. The sections are then locked together. • Tighten the handle.
14 – English FUEL HANDLING Fuel mixture 5 10 15 20 2% (1:50) 0,10 0,20 0,30 0,40 3% (1:33) 0,15 0,30 0,45 0,60 Gasolin Benzin Essence Gasolina Lit. Oil • Ö l Huile • Aceite Lit. 1 2 1/2 5 2% (1:50) 2 1/2 6 1/2 12 7/8 3% (1:33) 3 3/4 9 3/4 19 1/4 US gallon US fl.
English – 15 ST AR T AND ST OP Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P ress the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled.
16 – English Basic setting • The carburettor is set to its basic setting when test run at the factory. The basic setting is richer than the optimal setting and should be kept during the machine ‘ s first working hours. Thereafter the carburettor should be finely adjusted.
English – 17 MAINTENANCE H needle. The high speed needle is adjusted corr ectly when the machine ‘ splatters ’ a little . If the machine smokes heavily at the same time as it ‘ splatters ’ heavily the adjustment is too rich. The high speed needle affects the machine ’ s power , speed, temperature and fuel consumption.
18 – English MAINTENANCE Cooling system T o maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4.
English – 19 MAINTENANCE Angle gear The angle gear is filled with a sufficient quantity of grease at the factory . H owever , before using the machine you should check that the angle gear is filled to 3/4 with grease. U se HUSQV ARNA special grease.
20 – English MAINTENANCE Weekly maintenance 1. Check the starter, the starter cord and the return spring. 2. Make sure that the vibration damping elements are not damaged. 3. Clean the outside of the spark plug. Remove and check the electrode gap. Adjust the gap to 0.
English – 21 TECHNICAL D A T A Approved accessories Thread blade shaft M10 Plastic knifes T rimmer head Edger (LD) H edge trimmer (LD) Cutting attachment guard Art No.
22 – English EU declaration of conformity (Only applies to Europe) (Directive 89/392/EEC, Annex II, A) We, Husqv arna AB, S-561 82 Huskvarna, Sweden, tel: +46 36-146500, declare under sole responsib.
English – 23 1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm.
24 – English 1 T ri Cut 2 3 4 5 6 7 8 >20mm >20mm ! B.
English – 25 1 T rimmy H II 2 3 4 5 6 7 8 9.
26 – English 1 T rimmy Hit 23 4 5 6 7 8 9 10 11 “ Click ” “ Click ” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " ".
English – 27 1 T rimmy Hit Junior 2 5 6 7 8 9 10 12 “ Click ” 3 4 5,75 m 19' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 2,8 m 9'.
28 – English 1 T rimmy Hit Pro 2 5 6 7 8 9 10 12 “ Click ” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095".
English – 29 1 T rimmy Hit VI 2 5 6 3 4 7 8 9 10 11 “ Click ” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .
30 – English ´*30^¶6S¨ 1 2 3 4 5 6 7 8 9.
~ 15 cm 6' N ~ 15 cm 6' 502 25 56-01 502 26 04-01 502 25 53-01 502 26 24-01 (x2) 740 43 14-00 502 25 52-01 502 26 01-01 735 31 19-00 729 53 27-71 (x3) 738 21 03-04 502 26 03-01 502 27 07-01 .
2001W07 ´*30^¶6S¨.
We hope you find the links below useful. For further ga rdening information visit www.GardenResources.c o.uk Blower Vacs Brush cutters Brushcutters Chainsaws Chain saws Cultivators Cylinder lawn mower.
Ein wichtiger Punkt beim Kauf des Geräts Ryobi 227 L, 227 LD, 232 L, 240 L (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ryobi 227 L, 227 LD, 232 L, 240 L noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ryobi 227 L, 227 LD, 232 L, 240 L - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ryobi 227 L, 227 LD, 232 L, 240 L reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ryobi 227 L, 227 LD, 232 L, 240 L erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ryobi 227 L, 227 LD, 232 L, 240 L besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ryobi 227 L, 227 LD, 232 L, 240 L verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ryobi 227 L, 227 LD, 232 L, 240 L. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ryobi 227 L, 227 LD, 232 L, 240 L gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
