Benutzeranleitung / Produktwartung RNX-N150RT des Produzenten Rosewill
Zur Seite of 116
Wireless Router RNX-N150RT User Manual.
Wireless Router RNX-N150RT User Manual -2- COPYRIGHT & TRADEMARKS Specifications are subjec t to change without notice. is a registered trademark of Rosewill Inc. Other brands and product names are trademarks or registered trademarks of their respective holders.
Wireless Router RNX-N150RT User Manual -3- FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co -located or operating in con junction with any other antenna or transmitter .
Wireless Router RNX-N150RT User Manual -4- Industry Canada statement: This device complies with RSS-210 of the Industr y Canada Rules. Operati on is subject to the following two conditions: (1) This d.
Wireless Router RNX-N150RT User Manual -5- • Do not obstruct the device vent ilation slots, as insufficient airflow may harm your device. • Do not use this product near water, eg, in wet basement, or near a swimmin g pool. • Do not expose your device to dampness, dust or corrosive liquids.
Wireless Router RNX-N150RT User Manual -6- T able of Content s Package Co ntent s............................................................................................................... ................... 2 Chapter 1. Introduc tion ...........
Wireless Router RNX-N150RT User Manual -7- 4.5.3 MAC Cl one .......................................................................................................... 42 4.6 Wireless ....................................................................
Wireless Router RNX-N150RT User Manual -8- 4.12 Bandwidth Control ............................................................................................................ 79 4.12.1 Control Settings .................................................
Wireless Router RNX-N150RT User Manual - 2 - Package Contents The following items should be found in your package: z RNX-N150R T 150Mbps Wireless Lite N Router z Power Adapt er for RNX-N150RT 150Mbps .
Wireless Router RNX-N150RT User Manual - 3 - Chapter 1. Introduction Congratulations on your purcha se ofCongratulatio ns on your purchase of Rosewill’ s RNX-N150R T Wireless Lite N Rou ter . RNX-N150R T is a comb ined wired/wireless network connectio n device designed specifically for small bu siness, of fice and home ne tworking requirement s.
Wireless Router RNX-N150RT User Manual - 4 - mo ni to r th e ne two rk in re al ti me wi th th e r emo te management f un cti on . Since the Router is compatible with virtually all the major operating systems, it is very easy to manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in this user guide.
Wireless Router RNX-N150RT User Manual - 5 - 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 Front Panel sketch The Router’s LEDs and the WPS button are located on the front panel (View from left to right) .
Wireless Router RNX-N150RT User Manual - 6 - Name Statu s Indication Off Power is off. Power On Power is on. On The Router is initializing. Flashing The Router is working properly . System Off The Router has a system error . Off The Wireless function is disabled.
Wireless Router RNX-N150RT User Manual - 7 - 1.3.2 The Rear Panel Figure 1-2 Rear Panel sketch The following parts are lo cated on the rear panel (View from left to right). ¾ POWER: The Power socket is where you will co nnect the power adapt er . Please use the power adapter provided with this R N X - N 15 0 R T 150Mbps Wireless Lite N Router .
Wireless Router RNX-N150RT User Manual - 8 - Chapter 2. Connecting the Router 2.1 System Requirement s ¾ Broadband Internet Access Service (DSL/Cable/Ethernet) ¾ One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is connected directly to the Ethernet.
Wireless Router RNX-N150RT User Manual - 9 - 6. Connect the power adapter to the power socket on the Router , and th e other end into an electrical outlet.
Wireless Router RNX-N150RT User Manual - 10 - Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functi ons of your R N X -N 1 5 0R T 150Mbps Wireless Lite N Router using Quick Setup Wiz ar d within minutes.
Wireless Router RNX-N150RT User Manual - 1 1 - Figure 3-1 Success result of Ping command ¾ If the result displayed is similar to the Figure 3-2, it means the connection between yo ur P C and the Router is failed.
Wireless Router RNX-N150RT User Manual - 12 - Please check the connection following these step s: 1. Is the connection bet ween your PC and the Router correct? ) Note: The 1/2/3/4 LEDs of LA N ports which you link to on the Router and LEDs on your PC' s adapter should be lit.
Wireless Router RNX-N150RT User Manual - 13 - Step 2. Enter the default Login name and password “ admin” into the popup window and click OK . Step 3.
Wireless Router RNX-N150RT User Manual - 14 - Step 5. Click Auto-Detect in this window and RNX-N150 RT will detect and select connection option for you. Step 6. Enter your connection information. Y ou will need to verify with your ISP . PPPoE: Dynamic IP: Y ou do not need to enter anything in this option.
Wireless Router RNX-N150RT User Manual - 15 - Step 7. Set up your wireless signal. Step 8. Click Finish and you are read y! In order to connect wi relessly , you must select Enable Y ou can select you.
Wireless Router RNX-N150RT User Manual - 16 - 3.2.2 Quick Installation Guide – Detail and Explanation: 1. T o access the configuration utility , open a web-browser and type in the default address http://192.168.1.1 in the address field of the browser .
Wireless Router RNX-N150RT User Manual - 17 - Figure 3-5 Quick Setup 3. Click Next , and then WAN Connection Type page will appear, shown in Figure 3-6. Figure 3-6 WAN Connection Type The Router provides Auto-Detect function and supports three popular ways PPPoE , Dyn amic IP and Static IP to connect to the Intern et.
Wireless Router RNX-N150RT User Manual - 18 - Figure 3-7 Quick Setup - PPPoE ¾ User Name / Password - Enter the User Name and Passw ord provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP.
Wireless Router RNX-N150RT User Manual - 19 - Figure 3-9 Quick Setup – Wireless ¾ Wireless Radio - Enable or disable the wireless radi o choosing from the pull-down list. ¾ SSID - Enter a value of up to 32 characters. The same name of SSID ( Service Set Identification) must be assigned to all wirele ss devices in your network.
Wireless Router RNX-N150RT User Manual - 20 - ¾ Disable Security - The wireless security functi on can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router wit hout encryption. It is strongly recommended that you choose one of following options to enable security.
Wireless Router RNX-N150RT User Manual - 21 - Chapter 4. Configuring the Router This chapter will show each Web p age's ke y functions and the c onfiguration way . 4.1 Functions Page After your successful login, you will see the four teen main functions on the left of the Web-based utility .
Wireless Router RNX-N150RT User Manual - 22 - Figure 4-1 the main menu The detailed explanations for each Web page’ s key function are listed below .
Wireless Router RNX-N150RT User Manual - 23 - 4.2 S t atus Details The S tatus page provides the current status in formation about the Rout er . All information is read-only . Figure 4-2 Router S tatus 4.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide" .
Wireless Router RNX-N150RT User Manual - 24 - a) Choose menu “ WPS ”, you will see the next screen (shown in Figure 4-3 ). Figure 4-3 WPS ¾ WPS St atus - Enable or disable the WPS function here. ¾ Current PIN - The current value of the R outer's PIN is displayed her e.
Wireless Router RNX-N150RT User Manual - 25 - ) Note: To build a successful connection by WPS, you s hould also do the corresponding configuration of the new device for WPS function meanwhile. For the configuration of the new device, here takes the Wireless Adapter of our company for example.
Wireless Router RNX-N150RT User Manual - 26 - Method T wo: Step 1: Press the WPS button on the front panel of the Router . Step 2: For the confi guration of the wirele ss adapter , please choose “ Push the button on my access point ” in the configuration utility of t he WPS as below , and click Next .
Wireless Router RNX-N150RT User Manual - 27 - Step 3: W ait for a while until the next screen appears. Click Finish to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter Method Three: Step 1: Keep the default WPS Status as Enabled and click the Add device button in Figure 4-3, then the following screen will appear.
Wireless Router RNX-N150RT User Manual - 28 - Step 3: For the confi guration of the wirele ss adapter , please choose “ Push the button on my access point ” in the configurati on utility of the WPS as below , and click Next . The WPS Configuration Screen of Wireless Adapter Step 4: W ait for a while until the next screen appears.
Wireless Router RNX-N150RT User Manual - 29 - 4.4.2 By PIN If the new device supports Wi-Fi Protected Set up and the PIN method, you can add it to the network by PIN with the following two methods.
Wireless Router RNX-N150RT User Manual - 30 - ) Note: In this example, the default PIN code of this adapter is 16952898 as the above figure shown. Method T wo: Enter the PIN from my Router Step 1: Get the Current PI N code of the Router in Figure 4-3 (each Router has its unique PIN code.
Wireless Router RNX-N150RT User Manual - 31 - ) Note: a. The WPS LED on the Router will light gr een for five minutes if the device has been successfully added to the network. b. The WPS function cannot be conf igured if the Wireless Function of the Router is disabled.
Wireless Router RNX-N150RT User Manual - 32 - ¾ Subnet Mask - An address code that determines the size o f the network. Normally us e 255.255.255.0 as the subnet mask. ) Note: a. If you change the IP Address of LAN, you must use the new IP Address to log in the Router .
Wireless Router RNX-N150RT User Manual - 33 - ¾ Use These DNS Servers - If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the pri mary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assi gned dynamically from your ISP .
Wireless Router RNX-N150RT User Manual - 34 - ¾ MTU Size - The normal MTU (Maximum T ransmission Unit) va lue for most Ethernet networks is 1500 Bytes.
Wireless Router RNX-N150RT User Manual - 35 - z Dyn amic IP - Y ou can check this radio button to use Dynamic IP as the secondary connection to connect to the local area network provided by ISP . z St atic IP - Y ou can check this radio button to us e S tatic IP as the secondary connection to connect to the local area network provided by ISP .
Wireless Router RNX-N150RT User Manual - 36 - Figure 4-10 PPPoE Advanced Settings ¾ MTU Size - The default MTU size is “1480” bytes, which is usually fine.
Wireless Router RNX-N150RT User Manual - 37 - Figure 4-1 1 ¾ User Name/Password - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. ¾ Auth Server - Enter the authenticating serv er IP address or host name. ¾ Auth Domain - T ype in the domain suffix server name based on your location.
Wireless Router RNX-N150RT User Manual - 38 - ¾ Connect Automatically - The connection can be re-estab lished automatically when it was down. ¾ Connect Manually - Y ou can click the Connect / Disconnect button to connect/disconnect immediately . This mode also supports the Max Idle Time function as Connect on Demand mode.
Wireless Router RNX-N150RT User Manual - 39 - ¾ User Name/Password - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. ¾ Dynamic IP/ S tatic IP - Choose either as you are given by your ISP . Click the Connect button to connect immediately .
Wireless Router RNX-N150RT User Manual - 40 - Figure 4-13 PPTP Settings ¾ User Name/Password - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. ¾ Dynamic IP/ S tatic IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name.
Wireless Router RNX-N150RT User Manual - 41 - Internet connection to remain active at all times, enter “0” in the Max Idle T ime field. Otherwise, enter the number of minutes you want to have el apsed before your Internet connection terminates. ¾ Connect Automatically - Connect automatically after the Rout er is disconnected.
Wireless Router RNX-N150RT User Manual - 42 - 4.5.3 MAC Clone Choose menu “ Network → MAC Clone ”, you can configure the MA C address of the W A N on the screen below , Figure 4-14: Figure 4-14 MAC Address Clone Some ISPs require that you re gister the MAC Address of your adapter .
Wireless Router RNX-N150RT User Manual - 43 - 4.6 Wireless Figure 4-15 Wireless menu There are five submenus under the Wireless menu (shown in Figure 4-15): W ireless Settings , Wireless Security , Wireless MAC Filtering, Wireless Advanced and Wireless St atistics.
Wireless Router RNX-N150RT User Manual - 44 - wireless network security, the default SSID is set to be Rosewill_XXXXXX (XXXXXX indicates the last unique six numbers of eac h Router’s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test .
Wireless Router RNX-N150RT User Manual - 45 - ¾ Channel width - Select the channel width from the pull-down list. The default setting is automatic, which can adjust the channel width for your clients automatically.
Wireless Router RNX-N150RT User Manual - 46 - ¾ Auth Type - This option should be ch osen if the key type is WEP(ASCII) or WEP(HEX).It indicates the authorizati on type of the Root AP. ¾ Password - If the AP your Router is going to c onnect needs password, you need to fill the password in this blank.
Wireless Router RNX-N150RT User Manual - 47 - ¾ Disable Security - If you do not want to use wireless securi ty, check this radio button. But it’s strongly recommended to choose one of t he following modes to enable security. ¾ WEP - It is based on the IEEE 802.
Wireless Router RNX-N150RT User Manual - 48 - • Ve r s i o n - you can choose the version of the WPA security on the pull-down list. The default setting is Automatic , which can select WP A ( Wi-Fi Protected Access) or WP A2 ( WPA version 2) automatically based on the wireless stat ion's capability and request.
Wireless Router RNX-N150RT User Manual - 49 - Figure 4-21 • PSK Passphrase - You can enter a Passphrase between 8 and 63 characters. • Group Key Up date Period - Specify the group key update inte rval in seconds. The value should be 30 or above. Ente r 0 to disable the update.
Wireless Router RNX-N150RT User Manual - 50 - To Add a Wireless MAC Addre ss filtering entry, click the Add N ew… button. The " Add or Modify Wireless MAC Address Filtering entry " page wi.
Wireless Router RNX-N150RT User Manual - 51 - Address Filtering list by following t hese steps: 1. Click the Enable button to enable this function. 2. Select the radio button “Deny the stations not specified by any enabled entries in the list to access” for Filtering Rules .
Wireless Router RNX-N150RT User Manual - 52 - ¾ Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. ¾ Beacon Interval - Enter a value between 20-1000 millise conds for Beacon Interval here.
Wireless Router RNX-N150RT User Manual - 53 - Figure 4-25 Wireless S tatistics ¾ MAC Address - The connected wireless station's MAC address ¾ Current Status - The connected wireless station&apo.
Wireless Router RNX-N150RT User Manual - 54 - There are three submenus unde r the DHCP menu (shown in Figure 4 -26), DHCP Settings , DHCP Client s List and Address Reservation. Click any of them, and you will be able to configure the corre sponding function.
Wireless Router RNX-N150RT User Manual - 55 - ¾ Default Domain - (Optional.) Input the domai n name of your network. ¾ Primary DNS - (Optional.) Input the DNS IP address pr ovide d by your ISP or consult your ISP. ¾ Secondary DNS - (Optional.) Input the IP address of another DNS server if your ISP provides two DNS servers.
Wireless Router RNX-N150RT User Manual - 56 - Figure 4-29 Address Reservation ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry, either Enabled or Disabled .
Wireless Router RNX-N150RT User Manual - 57 - Click the Next button to go to the next page and Click the Previous button to return the previous page. 4.8 Forwarding Figure 4-31 The Forwarding menu There are four submenus under the Forwar ding menu (shown in Figure 4-31): Virtual Servers , Port T riggering , DMZ and UPnP .
Wireless Router RNX-N150RT User Manual - 58 - ¾ Service Port - The numbers of External Ports. Y ou c an type a service port or a rang e of service ports (in XXX – YYY format, XXX is the start port number , YYY is the end port number). ¾ IP Address - The IP Address of the PC pr oviding the service application.
Wireless Router RNX-N150RT User Manual - 59 - 1. Click the Modify in the entry you want to modify . If you want to delete the entry , click the Delete . 2. Modify the information. 3. Click the Save button. Click the Enable/Disabled All button to make all entries enabled/disabled.
Wireless Router RNX-N150RT User Manual - 60 - 3. When necessary ， the external host will be able to connec t to the local host using one of the ports defined in the Incoming Port s field. ¾ T rigger Port - The port for outgoing traffic. An outgoi ng connection using this port will trigger this rule.
Wireless Router RNX-N150RT User Manual - 61 - Figure 4-35 Add or Modify a Port T riggering Entry T o modify or delete an existing entry: 1. Click the Modify in the entry you want to modify . If you want to delete the entry , click the Delete . 2. Modify the information.
Wireless Router RNX-N150RT User Manual - 62 - Figure 4-36 DMZ T o assign a computer or server to be a DMZ server: 1. Check the Enable radio button 2. Enter the IP Address of a local host in the DMZ Host IP Address field 3. Click the Save button. ) Note: After you set the DMZ host, the firewa ll related to the host will not work.
Wireless Router RNX-N150RT User Manual - 63 - • Protocol - The type of protocol the Rout er opens for the application. • Internal Port - The Internal port the Router opens for local host. • IP Address - The IP address of the UPnP device that is currently accessing the Router.
Wireless Router RNX-N150RT User Manual - 64 - Figure 4-39 Basic Security ¾ Firewall - A firewall protects your network from the outside world. Here you can enable or disable the Router’s firewall.
Wireless Router RNX-N150RT User Manual - 65 - ¾ ALG - It is recommended to enable Application Lay er Gateway (ALG) because ALG allows customized Network Address T ranslation (NA T) traversal filters .
Wireless Router RNX-N150RT User Manual - 66 - ¾ DoS protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protecti on function.
Wireless Router RNX-N150RT User Manual - 67 - Figure 4-41 Local Management By default, the radio button “ All the PCs on the LAN are allowed to access the Router's Web-Based Utility ” is checked.
Wireless Router RNX-N150RT User Manual - 68 - ¾ Web Management Port - Web browser access normally uses the standard HTTP service port 80. This Router's default remote m anagement web port number is 80. For greater security, you can change the remote management w eb port to a custom port by entering that number in the box provided.
Wireless Router RNX-N150RT User Manual - 69 - TCP content s of the w ebsite will be examine by RNX-N150RT under the set rules. 4.10.1 Rule Choose menu “ Access Control → Rule ”, you can view and set Access Control rules in the screen as shown in Figure 4-44.
Wireless Router RNX-N150RT User Manual - 70 - 2. Give a name (e.g. Rule_1) for the rule in the Rule Name field. 3. Select a host from the Host drop-down list or choose “ Click Here To Add New Host List ”. 4. Select a target from the Target drop-sown list or choose “ Click Here To Add New Target List ”.
Wireless Router RNX-N150RT User Manual - 71 - with the Host Description is Host_1 and MAC Address is 00-11-22-33-44-AA. 2. Click “ Access Control → Target ” in the left to enter the Target Settings page. Add a new entry with the Target Description is Ta rget_1 and Domain Name is www.
Wireless Router RNX-N150RT User Manual - 72 - ¾ Host Description - Here displays the description of t he host and this description is unique. ¾ Information - Here displays the information about the host. It can be IP or MAC. ¾ Modify - To modify or delete an existing entry.
Wireless Router RNX-N150RT User Manual - 73 - Figure 4-48 Add or Modify a Host Entry For example : If you desire to restrict the inter net activities of host with MAC address 00-11-22-33-44-AA, you should first follow the settings below: 1. Click Add New.
Wireless Router RNX-N150RT User Manual - 74 - ¾ Modify - To modify or delete an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New… button. 2. In Mode field, select IP Address or Domain Name. z If you select IP Address , the screen shown is Figure 4-50.
Wireless Router RNX-N150RT User Manual - 75 - Figure 4-51 Add or Modify an Access T arget Entry For example : If you desire to restrict the inter net activities of host with MAC address 00-11-22-33-44-AA in the LAN to access www.google.com only, you should first follow the settings below: 1.
Wireless Router RNX-N150RT User Manual - 76 - Figure 4-52 Schedule Settings ¾ Schedule Description - Here displays the description of the schedule and this description is unique. ¾ Day - Here displays the day(s) in a week. ¾ Time - Here displays the time period in a day.
Wireless Router RNX-N150RT User Manual - 77 - Figure 4-53 Advanced Schedule Settings For example : If you desire to restrict the inter net activities of host with MAC address 00-11-22-33-44-AA to access www.google.com only from 18:00 to 20:00 on Saturday and Sunday , you should first follow the settings below: 1.
Wireless Router RNX-N150RT User Manual - 78 - Figure 4-54 S tatic Routing T o add static routing entries, follo w the step s below. 1. Click Add New… shown in Figure 4-54, you will see the following screen Figure 4-55. Figure 4-55 Add or Modify a S tatic Route Entry 2.
Wireless Router RNX-N150RT User Manual - 79 - Click the Previous button to view the information in the previous screen, click the Next button to view the information in the next screen. 4.12 Bandwid th Control Figure 4-56 There are two submenus under the Bandw idth Control menu as shown in Figure 4-56.
Wireless Router RNX-N150RT User Manual - 80 - 4.12.2 Rules List Choose menu “ Bandwidth Control → Rules List ”, you can view and configure the Bandwidth Control rules in the screen below . Figure 4-58 Bandwidth Control Rules List ¾ Description - This is the information about the rules su ch as address range.
Wireless Router RNX-N150RT User Manual - 81 - 4.13 IP& MAC Bing Setting Figure 4-60 the IP & MAC Binding menu There are two submenu s under the IP &MAC Binding menu (shown in Figure 4-60): Bindin g Setting and ARP List . Click any of them, and you will be able to scan or configure the corresponding function.
Wireless Router RNX-N150RT User Manual - 82 - ¾ Modify - To modify or delete an existing entry. When you want to add or modify an IP & MAC Binding entry, you can click th e Add New… button or Modify button, and then you will go to the next p age.
Wireless Router RNX-N150RT User Manual - 83 - Click the Enable All button to make all entries enabled. Click the Delete All button to delete all entries.
Wireless Router RNX-N150RT User Manual - 84 - 4.14 Dynamic DNS Choose menu “ Dynamic DNS ”, you can configure the Dynamic DNS function. The Router offers the DDNS (Dynamic Domain Name System) feat.
Wireless Router RNX-N150RT User Manual - 85 - 4.14.2 No-ip.com DDNS If you select www.no-ip.com , the page will appear as shown in Figure 4-66. Figure 4-66 No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. T ype the User Name for your DDNS account.
Wireless Router RNX-N150RT User Manual - 86 - 4.15 System T ools Figure 4-67 The System T ools menu Choose menu “ System T ools ”, you can see the subm enus un der the main menu: Time Settings , Diagnostic , Firmware Upgrade , Factory Default s, Backup & Restore, Reboot, Password, System Log and St atistics.
Wireless Router RNX-N150RT User Manual - 87 - Figure 4-68 T ime settings ¾ Time Zone - Select your local time zone from this pull down list. ¾ Date - Enter your local date in MM/ DD/YY into the right blanks. ¾ Tim e - Enter your local time in HH/MM/SS into the right blanks.
Wireless Router RNX-N150RT User Manual - 88 - 4.15.2 Diagnostic Choose menu “ System T ools → Diagnostic ”, you can transact Ping or Tr aceroute function to check connectivity of your net work in the following screen. Figure 4-69 Diagnostic T ools ¾ Diagnostic T ool - Check the radio button to select one diagnostic too.
Wireless Router RNX-N150RT User Manual - 89 - ¾ Ping Packet Size - The size of Ping packet. ¾ Ping Ti meout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. ¾ T raceroute Max TM - The max number of hops for a Traceroute connection.
Wireless Router RNX-N150RT User Manual - 90 - T o upgrade the Router's firmware, follow these instructions below: 1. Downl oad a more recent firmware upg rade file from the Rosewill website ( http://www .rosewill.com ). 2. Type the path and file nam e of the update file into the File field.
Wireless Router RNX-N150RT User Manual - 91 - ) Note: Any settings you have saved will be lost when the default settings are restored. 4.15.5 Backup & Restore Choose menu “ System T ools → Bac.
Wireless Router RNX-N150RT User Manual - 92 - • Change the LAN IP Address (syst em will reboot automatically). • Change the DHCP Settings. • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically).
Wireless Router RNX-N150RT User Manual - 93 - Figure 4-76 System Log ¾ Auto Mail Feature - Indicates whether auto mail feature is enabled or not. ¾ Mail Settings - Set the receiving and sending mailbox address, server ad dress, validation information as well as the timetable for Auto Mail Feature, as shown in Figure 4-77.
Wireless Router RNX-N150RT User Manual - 94 - z SMTP Server - Your smtp server. It corresponds wi th the mailbox filled in the From field. You can log on the relevant websit e for Help if you are not clear with the address. z Authentication - Most SMTP Server requires Authent ication.
Wireless Router RNX-N150RT User Manual - 95 - Figure 4-78 S tatistics ¾ Current Statistics Status - Enable or Disable. The default va lue is disabled. To enable, click the Enable button. If disabled, the function of DoS protection in Security settings will be disabled.
Wireless Router RNX-N150RT User Manual - 96 - Statistics Table: IP Address/ MAC Address The IP Address and MAC address are displayed with related statistics Packets The total number of packets rece ived and transmitted by the Router. Total Byt es The total number of bytes received and transmitted by the Router.
Wireless Router RNX-N150RT User Manual - 97 - Appendix A: FAQ 1. How do I configure the Router to access the Internet b y AD SL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your AD SL Modem to the W AN port on the Router .
Wireless Router RNX-N150RT User Manual - 98 - 2. How do I configure the Router to access the Internet b y Ethernet users? 1) Log in to the Route r , click the “ Netw ork ” menu on the left of your browser , and click " WA N " submenu.
Wireless Router RNX-N150RT User Manual - 99 - Figure A-4 V irtual Servers Figure A-5 Add or Modify a Virtual server Entry ) Note: Your opposite side should call your WAN IP , which is displayed on the “Status” page.
Wireless Router RNX-N150RT User Manual - 100 - 5) How to enable H323 ALG: Log in to the Router , click the “ Security ” menu on the left of your browser , and click “ Basic Security ” submenu. On the “ Basic Security ” page, check the Enable radio button next to H323 ALG .
Wireless Router RNX-N150RT User Manual - 101 - browser. 3) Log in to the Router , click the “ Forw arding ” menu on the lef t of your browse r , and click the " Virtual Servers " submenu.
Wireless Router RNX-N150RT User Manual - 102 - Appendix B: Configuring the PC In this section, we’ll introduce how to inst all and configure the TCP/IP correctly in Windows XP . First make sure your Ethernet Adapter is work ing, refer to the adapter ’s manual if necessary .
Wireless Router RNX-N150RT User Manual - 103 - Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
Wireless Router RNX-N150RT User Manual - 104 - Figure B-3 ) Note: For Windows 98 OS or before, the PC and Router may need to be restarted. ¾ Setting IP address manually 1 Select Use the following IP address radio button. And the fo llowing items available 2 If the Router's LAN IP addr ess is 192.
Wireless Router RNX-N150RT User Manual - 105 - Figure B-4 Now: Click OK to keep your settings..
Wireless Router RNX-N150RT User Manual - 106 - Appendix C: Specifications General St andards IEEE 802.3, 802.3u, 802.1 1b, 802.1 1g Compatible with 802.
Wireless Router RNX-N150RT User Manual - 107 - Sensitivity @PER 130M: -68dBm@10% PER 108M: -68dBm@10% PER; 54M: -68dBm@10% PER 1 1M: -85dBm@8% PER; 6M: -88dBm@10% PER 1M: -90dBm@8% PER Antenna Gain 5 dBi Environment al and Physical Operating : 0 ℃ ~40 ℃ (32 ~104 ℉℉ ) T emperature.
Wireless Router RNX-N150RT User Manual - 108 - Appendix D: Glossary ¾ 802.11b - The 802.11b standard specifies a wi reless networking at 11 Mbps using direct-sequence spread-s pectrum (DSSS) technology and oper ating in the unlicensed radio spectrum at 2.
Wireless Router RNX-N150RT User Manual - 109 - typically the configuration parameter for a wi reless PC card. It corre sponds to the ESSID in the wireless Access Point and to the wireless network name.
Ein wichtiger Punkt beim Kauf des Geräts Rosewill RNX-N150RT (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Rosewill RNX-N150RT noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Rosewill RNX-N150RT - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Rosewill RNX-N150RT reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Rosewill RNX-N150RT erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Rosewill RNX-N150RT besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Rosewill RNX-N150RT verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Rosewill RNX-N150RT. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Rosewill RNX-N150RT gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
