Benutzeranleitung / Produktwartung 2300 des Produzenten Rockford Fosgate
Zur Seite of 28
® ® 2300 / 2600 X / 4600 X A MPLIFIERS O WNER ' S M ANUAL Seri es 1.
Dear Customer, Congratulations on your purchase of America’s finest brand of car audio amplifiers. At Rockford Fosgate we are committed to musical reproduction at its best, and we are pleased you chose our product.
T ABLE OF C ONTENTS Specifications .................................................................................... 1 Introduction ...................................................................................... 3 Operating Features ........
– 1 – S PECIFICA TIONS Series 1 2300 Series 1 2600x Series 1 4600x Dynamic Power Rating (IHF 202 Standard) - Measured at 14.4 Voltage 1 Bridged/Mono into a 4 Ω Load 90 Watts 180 Watts 180 Watts .
– 2 – Series 1 2300 Series 1 2600x Series 1 4600x Signal-to-Noise Ratio Over 105 dB A weighted Bandwidth 10 Hz to 100 kHz ± 3dB Damping Factor @ 4 Ω At output connector - Over 200 Frequency Response 20 Hz to 20 kHz ± 0.5dB IM Distortion (IHF) Less than 0.
– 3 – I NTRODUCTION This manual provides information on the features, installation and operation of the Series 1 2300, 2600x and 4600x Amplifiers. We suggest you save this manual for future reference. We strongly recommend you have your Authorized Rockford Fosgate Dealer and Service Center install your new Series 1 amplifier.
Gold-Plated Connectors – of high quality to provide lower resistance and better reliability. Series 1 Housing – The extruded aluminum heatsink design of the Series 1 was designed for high performance cooling. – 4 – 2. for 4600x model 1. 3. 4. 1.
GND AP B+ +R – +L – – R+ – L+ Bridged Bridged – + – + – 5 – for 4600x model 5. Power/Speaker Connectors The gold-plated terminal block connectors are: GND Supplies ground to the amplifier.
I NST ALLA TION C ONSIDERA TIONS – 6 – This section focuses on some of the vehicle considerations for installing your new Series 1 amplifier. Checking your battery and current sound system, as well as pre-planning your system layout and best wiring routes will save installation time.
– 7 – T OOLS & S UPPLIES N EEDED Wire Cutters Phillips Screwdrivers Wire Strippers Flat Blade Screwdrivers Wire Crimpers Battery Post Wrench Voltmeter Electric Hand Drill with assorted bits Power Wire - [10-12 AWG; approx. 17’ (518.72 cm)] Grounding Wire - [10-12 AWG.
– 8 – P ASSENGER M OUNTING Under the seat or floor mounting will work as long as there is a minimum of 1” (2.5 cm) of air gap above the amplifier heatsink. Vertical mounting of the amplifier is still the best. Caution! Be sure to avoid running the power wires near the low level input cables, antenna, sensitive equipment or harnesses.
– 9 – 4. Input – The amplifier ’ s signal input RCA jacks should be con- nected to the source unit ’ s signal outputs with high-quality braided or double-shielded interconnecting RCA cables. Note: Be sure to route the Series 1 signal input cable away from the main power wire and the car ’ s wiring harnesses to avoid noise coupling.
– 10 – A CTIVE C ROSSOVER M ODE S ELECTIONS FOR THE 2600 X AND 4600 X The Series 1 2600x and the 4600x amplifiers feature a selectable electronic crossover. One module controls two output channels that can be configured in a High-Pass, Low-Pass, or Full Range (factory default) position.
– 11 – W IRING D IAGRAMS - 2300 / 2600 X 2300/2600 X B ASIC S YSTEM –+ Seri es 1 2300 2600x – + Source Unit 4 Ω (2 Ω min.) Right Full Range 4 Ω (2 Ω min.) Left Full Range *Xover Module (2600x only) Full Range Position GND AP B+ – L + – R + *See page 10 for proper crossover use.
– 12 – 2300/2600 X 3-W AY S TEREO /M ONO S YSTEM – + – + • • • • MX MX + – TX – + TX • • – + Source Unit Seri es 1 2300 2600x *Xover Module (2600x only) Full Range Position – R + – L + GND AP B+ Tweeter Tweeter 4 Ω Right Midrange 4 Ω Left Midrange 6.
– + – + • • • – + + – TX TX MX MX – + Seri es 1 2600x • Seri es 1 2600x – 13 – See page 10 for proper crossover use. 2600 X 3-W AY B I -A MPLIFIED S YSTEM Source Unit High Pass L.
W IRING D IAGRAMS - 4600 X – 14 – The following pages show some examples for wiring the Series 1 4600x amplifier to your vehicle's speaker system.
– 15 – 4600 X 3-W AY M ULTI -C HANNEL S TEREO /B RIDGED M ODE See page 10 for proper crossover use. + – – + + – • • • • TX – + TX – + GND AP B+ +R – +L – – R+ – L+ Bridge.
– 16 – 4600 X 2 C HANNEL B RIDGED L OW P ASS See page 10 for proper crossover use. Source Unit + – – + GND AP B+ +R – +L – – R+ – L+ Bridged Bridged Seri es 1 4600x LEFT RIGHT POWER LE.
–17 – T ROUBLESHOOTING This troubleshooting guide is intended to assist you with certain problems which may occur. If you still encounter problems, see your Authorized Rockford Dealer for assistance. Problem Amplifier will not play — Remote Turn-on light is off.
Problem Amplifier gets too hot. Solution 1. Be sure the amplifier is properly mounted. You should be able to place your hand a few inches above the amplifier housing and feel the heat rising when the unit is on. Hot air rises. Consequently mount the amplifier with the heatsink fins aligned vertically.
Problem Engine Noise (Whine) Solution 1. Disconnect the speakers from the amplifier. Connect a test speaker to the amplifier output terminals. If the noise goes away, check your speaker leads, speakers and crossovers. 2. If the noise persists, use a “ shorting plug ” to mute the input signal at the amplifier.
D YNAMIC P OWER M EASUREMENTS – 20 – Appendix A About the Dynamic Power Measurements The Audio Graph PowerCube is a test instrument used to measure the output of an amplifier. It makes measurements in accordance with IHF- 202 standards. The IHF-202 standard is a Dynamic power measurement.
– 21 – Information Cubed The data acquired in the testing procedure is then graphed in the form of a 3-dimensional cube, hence the name PowerCube . The Phase Angle is expressed on the horizontal axis, the Output Voltage is presented on the vertical axis and the Impedance is displayed on the Z axis.
W ARRANTY I NFORMA TION – 22 – Rockford Fosgate warrants all electronics to the original consumer/purchaser to be free from defects in materials or workmanship for a period of three (3) years. We will cover parts and labor provided the product was purchased from an Authorized Rockford Fosgate Dealer.
N OTES.
N OTES.
REV. C 1/94 MAN-0191 Rockford Fosgate A Division of Rockford Corporation 546 South Rockford Drive Tempe, Arizona 85281 U.S.A. In U.S.A., (602) 967-3565 In Canada, call Korbon (905) 567-1929 In Europe,.
Ein wichtiger Punkt beim Kauf des Geräts Rockford Fosgate 2300 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Rockford Fosgate 2300 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Rockford Fosgate 2300 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Rockford Fosgate 2300 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Rockford Fosgate 2300 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Rockford Fosgate 2300 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Rockford Fosgate 2300 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Rockford Fosgate 2300. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Rockford Fosgate 2300 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
