Benutzeranleitung / Produktwartung Ray48 des Produzenten Raymarine
Zur Seite of 42
Ray48 VHF Radio Owner’ s Handbook Document number: 81233 -2 Date: February 200 4.
ii PURPOSE THIS MANUAL CONT AINS VER Y IMPOR T ANT INFORMA TION ON THE INST ALLA TION, OPERA TION, AND MAINTENANCE OF YOUR NEW EQUIPMENT . TO GET THE BEST RESUL TS IN OPERA TION AND PERFORMANCE, PLEASE T AKE THE TIME TO READ THIS MANUAL THOROUGHL Y . *******IMPORT ANT NO TICE******* THIS DEVICE IS ONL Y AN AID TO NA VIGA TION.
iii T ABLE OF CONTENTS SECTION 1 GENERAL DESCRIPTION 1.1 INTRODUCTION .................................................................................................................................... 1 1.2 EQUIPMENT FEA TURES ......................
i v SECTION 4 TECHNICAL DESCRIPTION 4.1 GENERAL ..................................................................................................................... ........................ 14 4.2 THE CONTROL SECTION .................................
v GLOSSAR Y OF TERMS VHF ............................................................. V ery High Frequency 30MHz to 300MHz FM ............................................................... Frequency Modulation Carrier W ave .........................
1 SECTION 1 GENERAL DESCRIPTION 1.1 INTR ODUCTION Congratulations on your purchase of Raymarine's Ray48 marine radiotelephone. The Ray48 is a CPU-controlled, digitally synthesized, compact transc.
2 SECTION 2 INST ALLA TION 2.1 UNP A CKING AND INSPECTION Use care when unpacking the unit from the shipping carton to prevent damage to the contents. It is also good practice to save the carton and the interior packing material. The original packing material should be used in the unlikely event it is necessary to return the unit to the factory .
3 • The transceiver should be located as near to the power source as possible. • The selected location should be as far apart as is possible from any devices that may cause interference such as motors, generators, and other on board electronics.
4 Fig.2-2 OUTLINE AND MOUNTING DIMENSIONS All dimensions are shown in (inches) and millimeters 120(4.72) 85(3.03) 110(4.33) 160(6.29) 151(5.94) 195(7.66) 19(0.
5 Fig.2-3 REAR VIEW CA UTION Do not install this radio on vessels with positive ground batter y systems. Fig.2-4 PO WER/EXTERNAL SPEAKER CABLE AND 4 PIN CONNECT OR CABLE 2.4.1 DC P ower and External Speaker Connections The power cable comes with external speaker attachments.
6 Y our Ray48 radio should be connected to the nearest primary source of ship's DC power . A typical source may be a circuit breaker on the power panel or a fuse block near the unit. When connecting to either of these sources, the circuit breaker or other in-line fuse should be rated at 10 amps.
7 2.4.3 Antenna Connections The coaxial cable to your VHF antenna is intended to be connected to the antenna jack on the rear panel using a PL259 VHF type connector . The antenna cable can be cut to length but the overall cable length can be critical to performance.
8 Fig.3-1 LA Y OUT OF CONTROLS AND CONNECT ORS SECTION 3 OPERA TIONS 3.1 INT R ODUCTION Y our Ray48 has the capability to transmit and receive on all available US and International Marine VHF radiotelephone channels.
9 3.2.1 Contr ols 1 VOLUME Control (On/Off) T urns the radio On and Off and controls the V olume of the audio output to the speaker . 2 [ ▲ ] [ ▼ ] Keys The Up and Down keys are used to move the channel numbers up or down.
10 3.2.2 LCD Displa y The following describes the functional characters on the Ray48's LCD. 1 SCAN: W ill flash by itself when All-Scan mode is to be initiated or will flash in unison with "MEM" when Memory Scan mode is to be initiated.
11 3.3 OPERA TING PROCEDURES 3.3.1 T urning the P ower On 1) Rotate the ON/OFF/VOLUME control clockwise to turn the radio on. NOTE When the Pow er is on, the synthesizer automatically prog rams for the USA channel frequencies and selects the calling channel 16.
12 NOTE Initial communication contacts are usually made over channel 16 as all ships and shor e stations monitor this channel. T hen a shift to a working channel will be necessar y . T o Select a W eather Channel 1) Press the WX/INT key , then use the Up [ ▲ ] or Down [ ▼ ] key to select the desired weather channel from 0 to 9.
13 2) Memory Scan Mode If one or more channels are stored in memory , when the SCAN key is pressed, "SCAN" and "MEM" will begin to flash simultaneously on the LCD. If no other key is pressed, the radio will begin scanning all channels currently in memory in three seconds.
14 SECTION 4 TECHNICAL DESCRIPTION 4.1 GENERAL The Ray48 can be considered as consisting of two major sections. They are: • The Control Circuitry (considering of the front panel controls, the LCD display , control CPU) • The T ransmitter/Receiver/PLL circuits 4.
15 4.3.2 T ransmitter Circuit A signal from the microphone is fed to a pre-emphasis operations amplifier IC3, and modulates VCO (Q4) through active LPF IC2. The VCO output signal from Q4 is sent to the RF power amplifiers IC1, Q1 and Q2 through buffer amplifier Q3.
16 4.4 SPECIFICA TIONS 4.4.1 T ransmitter Channels 53 US/International Frequency Stability ±10PPM (±0.001%) (-20°C to +50°C) Frequency Range 156.025 to 157.425 MHz Channel Spacing 25 KHz Increments Power Output 25 W atts switchable to 1 W att into 50 Ohms at 13.
17 4.4.3 Operating Requirement Input V oltage 13.6 Vdc ±15% (1 1.6 to 15.6 Vdc) Current Required T ransmit Less than 5.8 amp at 25 W atts Less than 1.5 amp at 1 W att Operating T emperature -20°C to +50°C Duty Cycle Continuous, 80% receive, 20% transmit (max 10 min.
18 POWER MODULE DRIVE ANT SW AF AMP PWR DET DC CONT BUFF AMP BAND SW VCO DC FIL SW SW SW SW PLL FIL SW RESET IC201 M34520 M6 +5V REG E 2 PROM KEY BOARD LCD DISPLA Y PRE ⋅ ENPH & LIMITER LPE SW S.
.
19 8 9 10 1 6 30 28 27 20 21 22 2 11 12 15 16 31 4 14 13 17 18 32 33 5 29 35 23 24 3 19 25 26 7 34 4.6 Ray48 ASSEMBL Y DRA WING 1. FRONT P ANEL ASSEMBL Y 2. MID COVER ASSEMBL Y 3. REAR COVER 4. FRONT GASKET 5. REAR GASKET 6. FRONT PCB ASSEMBL Y 7. MAIN PCB ASSEMBL Y 8.
20.
21 SECTION 5 MAINTENANCE 5.1 GENERAL The Ray48 is designed to provide long periods of trouble-free operation. It is recognized, however , that environmental and other factors may result in a need for occasional service. 5.1.1 How to contact Ra ymarine T echnical Support: 1-800-539-5539 ext.
22 On the Internet V isit the Raymarine W orld W ide W eb site for the latest information on Raymarine electronic equipment and systems at: www .raymarine.
23 SECTION 6 Ra y48 MARINE CHANNELS FREQUENCY T ABLES 6.1 Ra y48 MARINE CHANNELS AND THEIR USA GE Port Operations and Commercial, VTS. Available only in New Orleans/Lower Mississippi area. Port Operations or VTS in the Houston, New Orleans and Seattle areas.
24 CH No. Use XMIT RCV Single Frequency x x x x 157.075 U.S. Government only - Environmental protection operations. U.S. Government only U.S. Government only Public Correspondence (Marine Operator) Public Correspondence (Marine Operator) 81 A 82 A 83 A 84 85 157.
25 Public Correspondence, Port Operations and Ship Movement Public Correspondence, Port Operations and Ship Movement Public Correspondence, Port Operations and Ship Movement Public Correspondence, Por.
26 Intership channels are for communications between ship stations. Intership communications should be restricted to Channels 6, 8, 72 and 77. If these are not available, the other channels marked for Intership may be used. Channels 10, 67 and 73 should be avoided within VHF range of coastal areas in Europe and Canada.
27 SECTION 7 APPENDIX 7.1 VHF MARINE CHANNEL USA GE GUIDE AND LICENSING REQUIREMENTS Marine VHF radio users in the US must comply with all applicable FCC rules and regulations, some of which are described here. This information was current at the time this book was printed.
28 All transceivers, hand-helds included, operated in the Maritime Radio Services are required to be operated under an appropriate maritime station license. Operation of hand held VHF Marine transceivers without proper station license can lead to fines and/or administrative sanctions issued against its user and/or owner .
29 Emergency Calling Monitoring Intership Safety U.S. Coast Guard Navigation Port Operation Noncommercial Commercial Marine Operator State Control Environmental W eather USAGE GUIDE.
30 Emergency Channel 16 If: • Y our ship is sinking, or on fire • Someone has been lost overboard • There exists grave and imminent danger Use this distress procedure: • Select Channel 16 • Say "Mayday , Mayday , Mayday .
31 Monitoring Channel 16 & W orking Channel When - your VHF station is turned on and it is not being used to exchange communications Y ou Must - monitor channel 16 As an operating convenience, many stations employ a second receiver so that they can monitor a working channel and channel 16 simultaneously .
32 U .S. Coast Guard Channel: 22 V essels: Any Use: W orking channel for exchange of communica- tions with stations of the U.S. Coast Guard. Between: Ship to U.S. Coast Guard ship, coast to aircraft stations Comments: U.S. Coast Guard does not regularly monitor this channel.
33 P or t Operations Channels: 5, 12, 14, 20, 65, 66, 73, 74 [77] V essels: Any Use: Messages relating to the operational handling, movement and safety of vessels in or near ports, locks and waterways.
34 Commercial Channels: 7, 8, 9, 10, 1 1, 18, 19, 67, 79, 80, [88] V essels: Those used primarily for commercial transport of persons or goods, or engaged in servicing other vessels Use: Communication.
35 State Control Channel: 17 V essels: State and local govern- ment Use: Coordination, regulation and control of boating activities and the rendering of assistance to vessels. Between: Ship and coast stations associated with state and local governments.
36 PHONETIC ALPHABET : T o help make call letters more clearly understood, and to assist in spelling out similar sounding or unfamiliar words, radiotelephone users employ the international phonetic alphabet.
Ein wichtiger Punkt beim Kauf des Geräts Raymarine Ray48 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Raymarine Ray48 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Raymarine Ray48 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Raymarine Ray48 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Raymarine Ray48 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Raymarine Ray48 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Raymarine Ray48 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Raymarine Ray48. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Raymarine Ray48 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
