Benutzeranleitung / Produktwartung IPmux-11 des Produzenten RAD Data comm
Zur Seite of 148
Installation and Operation Manual IPmux-11 TDM Pseudowire Access Gateway Version 2.00.
.
IPmux-11 TDM Pseudowire Access Gateway Version 2.00 Installation and Operation Manual Notice T h i s m a n u a l c o n t a i n s i n f o r m a t i o n t h a t i s p r o p r i e t a r y t o R A D D a t a C o m m u n i c a t i o n s L t d . ( " R A D " ) .
Limited Warranty RAD warrants to DISTRIBUTOR that the hardware in the I Pmux -11 to be delivered hereunder shall be free of defects in material and workmans hip under no rmal use and service for a period of twelve (12) months following the date of shipment to DISTRIBUTOR.
Product Disposal To facilitate the reuse, recycling and ot her forms of recovery of waste equipment in protecting the environm ent, the owner of this RAD product is required to refrain from disposing of this pr oduct as unsorted municipal waste at the end of its life cycle.
In some cases, the users may insert their own SFP la ser transceivers into the product. Users are alerted that RAD cannot be held responsible for any damage th at may result if non-compliant transceivers are used.
The maximum permissible current capability of the branch distribution circuit that supplies power to th e product is 16A. The circuit breaker in the building installatio n should have high breaki ng capacity and m ust operate at short-circuit current exceeding 35A.
Some SELV and non-SELV circuits use the same connectors. Use caution when connecting cables. Extra caution should be exer cise d during thunderstorms. When using shielded or coaxial cables, verify that there is a good ground connection at both ends. The earthing and bonding of the ground connectio ns should comply with the local codes.
FCC-15 User Information This equipment has been tested and found to comply with the limits of the Class A digital device, pursuant to Part 15 of the FCC rules. These limi ts are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Declaration of Conformity Manufacturer's Name: RAD Data Communications Ltd. Manufacturer's Address: 24 Raoul Wallenberg St. Tel Aviv 69719 Israel declares that the product: Product Name: IPm.
IPmux-11 Ver. 2.00 Configuring IPmux-11 1 Quick Start Guide Installation of IPmux-11 should be carrie d out only by an experienced technician. If you are familiar with IPmux-11, use this guide to prepare the unit for operation. 1. Installing IPmux-11 Connecting the Interfaces 1.
Quick Start Guide Installation and Operation Manual 2 Configuring IPmux-11 IPmux-11 Ver. 2.00 Configuring the IP Management Parameters The host IP address, subnet mask and default gateway IP address must be configured via an ASCII terminal.
IPmux-11 Ver. 2.00 i Contents Chapter 1. Introduction 1.1 Overview ..................................................................................................................... 1-1 Versio ns ....................................................
Table of Contents Installation an d Operation M anual ii IPmux-11 Ver. 2.00 Chapter 4. Configuration 4.1 Configuration Sequence .............................................................................................. 4-1 4.2 Configuring IPmux-11 for Management .
IPmux-11 Ver. 2.00 Overview 1-1 Chapter 1 Introduction 1.1 Overview IPmux-11 offers a solution for extendin g tradit ional E1/T1 transparently over packet switched networks (PSNs) such as IP, Ethernet, and MPLS networks.
Chapter 1 Introduction Installation and Operation Manual 1-2 Overview IPmux-11 Ver. 2.00 Application Figure 1-1 ill ustrates a typical IPmux-11 multiplexing voice and Ethernet traffic over an IP link. Figure 1-1. Multiplexing Voice and Et hernet over a Packet-Switched Network Features E1 Interface The E1 port complies with G.
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Overview 1-3 IP The data stream coming from the E1 or T1 port is converted into IP packets that are transported over the Fast Ethernet ports, and vice versa. TDM bytes are encapsulated in a UDP frame that runs over IP an d over Ethernet.
Chapter 1 Introduction Installation and Operation Manual 1-4 Overview IPmux-11 Ver. 2.00 QoS QoS supports: • Labeling IP level priority (ToS/Diffserv) for TDMoIP packets • VLAN tagging and priority labeling according to IEEE 802.1p&Q for TD MoIP packets • QoS marking of the TDMoIP traffic in MPLS networks.
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Functional Description 1-5 1.2 Physical Description IPmux-11 is a compact easy-to-install standalone unit. Figure 1-2 shows a 3-dimens ional view of IPmu x-11. Figure 1-2. IPmux-11 3D View The front panel includes the IPmux-11 LEDs .
Chapter 1 Introduction Installation and Operation Manual 1-6 Functional Description IPmux-11 Ver. 2.00 Unframed In the unframed mode, the incoming bit st ream from each channel (regardless of framing) is converted into IP over Eth e rnet frames. This option provides clear channel end-to-end se rvice (unframed).
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Functional Description 1-7 • Internal timing – in this mode, the Tx clock is derived from an internal oscillator. • External timing – in this mode the Tx clock is derived from the external clock input.
Chapter 1 Introduction Installation and Operation Manual 1-8 Functional Description IPmux-11 Ver. 2.00 Figure 1-4. IPmux-11 in Ex ternal Clock Mode Single Source Clock Network When a common clock is n.
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Functional Description 1-9 Table 1-2. TDMoIP Frame Structure Field Length (Bytes) Field 7 Preamble 1 SFD 6 Destination MAC A.
Chapter 1 Introduction Installation and Operation Manual 1-10 Functional Description IPmux-11 Ver. 2.00 VLAN Support VLAN, according to IEEE 802.1p& Q, adds four byt es to the MAC layer of the Ethernet frame. The user can set the cont ents of these bytes, MAC layer priority and VLAN ID.
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Functional Description 1-11 Table 1-4. TDMoMPLS Frame Structure Field Length (Bytes) Field 7 Preamble 1 SFD 6 Destination MAC Address 6 Source MAC Address 2 Type 20 Outer label 3 EXP 1 Stacking bit 8 TTL 20 Inner label 3 EXP 1 Stacking bit 8 TTL .
Chapter 1 Introduction Installation and Operation Manual 1-12 Functional Description IPmux-11 Ver. 2.00 PDVT (Jitter) Buffer IPmux-11 is equipped with a Packet DVT (Delay Variation Tol erance) buffer. The PDVT buffer or jitter buffer is filled by the incoming IP packets and emptied out to fill the TDM stream.
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Functional Description 1-13 Configuring the TDM byt es per frame (TDM bytes/frame) parameter has impact on the Ethernet throughput (bandwidth or traf fic traveling through the Ethernet).
Chapter 1 Introduction Installation and Operation Manual 1-14 Functional Description IPmux-11 Ver. 2.00 Where: • VLAN is an optional field: if enabled it adds 4 bytes to the frame overhead • paylo.
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Functional Description 1-15 For V1 the maximum number of frames that can be reordered is 7, even if the calculation result exceeds 7. For V2 th e maximum number of frames that can be reordered is 64, even if t he ca lculation result exceeds 64.
Chapter 1 Introduction Installation and Operation Manual 1-16 Functional Description IPmux-11 Ver. 2.00 IPmux-11 transfers fault condit ions only if the payload format is configured to V2. The fault conditions are transferre d as follows: • Framed E1 or T1: RDI as RDI, LOS and AIS as AIS • Unframed E1 or T 1: LOS and AIS as AIS.
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Functional Description 1-17 Internal Swi tch TDMo IP E1 o r T1 P ort Et hernet Networ k Port Et hernet User Port 1 Et hernet User Port 2 Figure 1-11. IPmux-11 with Two Ethernet User Port Priority is always given to TDMoIP packets insi de the internal switch.
Chapter 1 Introduction Installation and Operation Manual 1-18 Functional Description IPmux-11 Ver. 2.00 Table 1-7. Automatic Per-Port Rate Limiting Default VLAN Priority Automatic Rate Limiting 4 - 7 64 Mbps 2 - 3 32 Mbps 0 - 1 16 Mbps Table 1-8 illustrates relations between rate limiting and VLAN tagging modes.
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Functional Description 1-19 Switch Behavior When Handling User and Network Traffic The way the network and user ports handle the traffic depends on the selected port mode (transparent , untagged, tagged or double tagged) and fra me type (untagged, tagged or double tagged).
Chapter 1 Introduction Installation and Operation Manual 1-20 Functional Description IPmux-11 Ver. 2.00 Table 1-12. Mode C Ingress Egress If a tagged frame enters the transparent port, it is switched .
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Functional Description 1-21 Table 1-14. Mode E Ingress Egress If a tagged frame enters the untagged port, it is switched to .
Chapter 1 Introduction Installation and Operation Manual 1-22 Functional Description IPmux-11 Ver. 2.00 Table 1-16. Mode G Ingress Egress If a double-tagged frame enters the transparent port, it is sw.
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Functional Description 1-23 Switch Behavior When Hand ling Management Traffic Table 1-17 lists operation modes of the network port when handl ing the management traffic. Table 1-17.
Chapter 1 Introduction Installation and Operation Manual 1-24 Technical Specifications IPmux-11 Ver. 2.00 1.4 Technical Specifications E1 Interface Compliance ITU-T Rec.
Installation and Operation Manual Chapter 1 Introduction IPmux-11 Ver. 2.00 Technical Specifications 1-25 Timing Transmit • Internal • External input or output via dedicated connector: E1/T1 or 20.
Chapter 1 Introduction Installation and Operation Manual 1-26 Technical Specifications IPmux-11 Ver. 2.00.
IPmux-11 Ver. 2.00 Site Requirements and Prerequisites 2-1 Chapter 2 Installation and Setup 2.1 Introduction This chapter describes installation and se tup procedures for the IPmux-11 unit. After installing the unit, re fer to Chapter 3 for the operating instructions.
Chapter 2 Installation and Setup Installation and Operation Manual 2-2 Connecting the Ethernet Equipment IPmux-11 Ver. 2.00 2.3 Package Contents The IPmux-11 package includ es the following items: •.
Installation and Operation Manual Chapter 2 Installation and Setup IPmux-11 Ver. 2.00 Connecting to the E1/T1 Devices 2-3 Connecting the Ethernet User Equi pment Figure 2-3 illustrates a rear panel of th e IPmux-11 unit with two user LAN ports. CO NTRO L EXT C LK E1 ETH 123 SET DEF Figure 2-3.
Chapter 2 Installation and Setup Installation and Operation Manual 2-4 Connecting IPmux-11 to Power IPmux-11 Ver. 2.00 2.6 Connecting to the External Clock Source IPmux-11 is connected to the external clock source via a balance d RJ-45 connector designated EXT CLK.
Installation and Operation Manual Chapter 2 Installation and Setup IPmux-11 Ver. 2.00 Connecting IPmux-11 to Power 2-5 Before connecting or disconnecting any cable, t he protective earth terminals of this unit must be connected to the protective ground conductor of the mains (AC or DC) power cord.
Chapter 2 Installation and Setup Installation and Operation Manual 2-6 Connecting IPmux-11 to Power IPmux-11 Ver. 2.00.
IPmux-11 Ver. 2.00 Controls and Indicators 3-1 Chapter 3 Operation This chapter: • Provides a detailed description of the front panel c ontrols and indicators a nd their functions • Explains power.
Chapter 3 Operation Installation and Operation Manual 3-2 Controls and Indicators IPmux-11 Ver. 2.00 Table 3-1. IPmux-11 LED s and Controls Name Type Function Location PWR Green LED ON – Power is ON.
Installation and Operation Manual Chapter 3 Operation IPmux-11 Ver. 2.00 Default Settings 3-3 3.3 Default Settings The following table lists the default settings of the IPmux-11 co nfiguration parameters. Table 3-2. Default Settings Parameter Default Value System IP address Empty IP mask Empty Default gateway 0.
Chapter 3 Operation Installation and Operation Manual 3-4 Default Settings IPmux-11 Ver. 2.00 Table 3-2. Default Settings (Cont.) Parameter Default Value Fall back clock source Port1 Master clock Ex t.
Installation and Operation Manual Chapter 3 Operation IPmux-11 Ver. 2.00 Default Settings 3-5 Table 3-2. Default Settings (Cont.) Parameter Default Value Trail mode Termination Physical Layer (ETH) Ch.
Chapter 3 Operation Installation and Operation Manual 3-6 Configuration Alternatives IPmux-11 Ver. 2.00 3.4 Configuration Alternatives If required, IPmux-11 can be reconfig ured.
Installation and Operation Manual Chapter 3 Operation IPmux-11 Ver. 2.00 Configuration Alternatives 3-7 To enter as a user: 1. Enter user for u ser name. 2. Enter 1234 for pass word. If the password is invalid in three consecutive attempts, the system becomes inaccessible for 15 minutes.
Chapter 3 Operation Installation and Operation Manual 3-8 Configuration Alternatives IPmux-11 Ver. 2.00 Type the line number corr esponding to the desired value, and then press <Enter> To enter a value which requires free text entry, type in the desired string and then press <Enter> .
Installation and Operation Manual Chapter 3 Operation IPmux-11 Ver. 2.00 Configuration Alternatives 3-9 General Web Browsers Operating Procedures To manage IPmux-11 via Web browser: 1.
Chapter 3 Operation Installation and Operation Manual 3-10 Configuration Alternatives IPmux-11 Ver. 2.00 Overview of Menu Operations Use these menu trees as a reference ai d while performing configuration and control functions. Chapter 4 illustrates menus an d explains parameters.
Installation and Operation Manual Chapter 3 Operation IPmux-11 Ver. 2.00 Configuration Alternatives 3-11 Configuration Connection Bundle Connecti on 1. System 2. Physical layer 3. Connection 4. Bridge 1. Bundle ID 2. DS0 bundle 3. Bundle connection 1.
Chapter 3 Operation Installation and Operation Manual 3-12 Turning IPmux-11 Off IPmux-11 Ver. 2.00 Diagnostics Ping Loopback Self Test Results 1. Pin g 2. Trace route 3. Loopback 4. Self test resu lts 1. Destinati on IP address 2. VLAN tagging 3. 5. Number of frames to send 6.
IPmux-11 Ver. 2.00 Configuration Sequence 4-1 Chapter 4 Configuration This chapter illustrates the IPmux-11 c onfiguration screens an d explains their parameters.
Chapter 4 Configuration Installation and Operation Manual 4-2 Configuring IPmux-11 for Management IPmux-11 Ver. 2.00 4.2 Configuring IPmux-11 for Management The IPmux-11 management software allows yo .
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Management 4-3 To enable DHCP client : 1. From the System menu, select Host IP . The Host IP menu appears (see Figure 4-2 ). 2. Fr om the Host IP menu , select DHCP , and choose Enabl e .
Chapter 4 Configuration Installation and Operation Manual 4-4 Configuring IPmux-11 for Management IPmux-11 Ver. 2.00 To acquire a new IP address from the DHCP server: 1. From the Host IP menu, set all host IP parameters (host IP, IP mask and default gateway) to 0.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Management 4-5 To define read, write and trap communities: 1. From the Management menu, select Authentication/community . The Authentication/Communi ty menu appears (see Figure 4-4 ).
Chapter 4 Configuration Installation and Operation Manual 4-6 Configuring IPmux-11 for Management IPmux-11 Ver. 2.00 It is possible to set up a local or re mote management link using the manager location and VLAN configuration. Refer to the configuration example at the end of this section.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Management 4-7 Configuration Example Local Management Figure 4-6 illustrates how to manage a local IPmux-11 from an NMS connected via Ethernet user port 2.
Chapter 4 Configuration Installation and Operation Manual 4-8 Configuring IPmux-11 for Management IPmux-11 Ver. 2.00 User 2 User 2 Network Netwo rk Management Tr affic (VLA N 1) User Traffic (VLAN 100.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Management 4-9 Select Access , and specify the user’s access methods (ASCII ter minal, Telnet, Web browser, Telnet and Web browser, or all of them).
Chapter 4 Configuration Installation and Operation Manual 4-10 Configuring IPmux-11 for Management IPmux-11 Ver. 2.00 Enable (Telnet, SNMP or Web access is enabled) Disable (Telnet, SNMP or Web access is disabled) Manager Only (Access is allowed only for the statio ns appearing in the manager list).
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Operation 4-11 To select the baud rate: 1. From the System menu ( Figure 4-1 ), select Control port . The Control Port menu is displayed (se e Figure 4-11 ).
Chapter 4 Configuration Installation and Operation Manual 4-12 Configuring IPmux-11 for Operation IPmux-11 Ver. 2.00 Channel 4 External Fall back clock (Fall back clock type): Internal.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Operation 4-13 Configuring IPmux-11 at the Physical Level The TDM (E1 or T1) and Ethernet interfaces of IPmux-11 must be configured at the physical level.
Chapter 4 Configuration Installation and Operation Manual 4-14 Configuring IPmux-11 for Operation IPmux-11 Ver. 2.00 Rx sensitivity (Maximum attenuatio n of the receive signal that can be compensa.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Operation 4-15 Configuration>Physical layer>TDM (E1) Channel ID (1) Restoration time >(CCITT) Signaling mode (CAS Disabled) 1. Admin status (Enable) 2.
Chapter 4 Configuration Installation and Operation Manual 4-16 Configuring IPmux-11 for Operation IPmux-11 Ver. 2.00 To configure T1 interface: • From the TDM (T1) men u, configure the following.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Operation 4-17 Line buildOut (CSU mo de only, Tx gain level relative to T1 output tran smit level) 0 dB (No attenuation) 7.5 dB (Attenuation of 7.
Chapter 4 Configuration Installation and Operation Manual 4-18 Configuring IPmux-11 for Operation IPmux-11 Ver. 2.00 Configuration>Physical layer>TDM (T1) Channel ID (1) 1. Admin status (Enable) 2. Transmit clock source >(Adaptive) 3. Rx sensitivity (Short haul) 4.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Operation 4-19 3. When the required Ethernet interfac e is displayed, configure the following: .
Chapter 4 Configuration Installation and Operation Manual 4-20 Configuring IPmux-11 for Operation IPmux-11 Ver. 2.00 Configuring Bund le Connections IPmux-11 supports one bundle that can includ e up to 31 E1 or up to 24 T1 timeslots. The bundle can be connected to any bundle of the TDMo IP device that operates opposite IPmux-11.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Operation 4-21 Destination bundle (bundl e number in the destin ation device): 1–8063 Next hop address (Use the next hop parameter when the destination address is not in the devic e subnet.
Chapter 4 Configuration Installation and Operation Manual 4-22 Configuring IPmux-11 for Operation IPmux-11 Ver. 2.00 Sensitive (Whether to optimize the cl ock for acc urateness or for constant delay): Data (Accurate clock is more important than constant delay.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Operation 4-23 Configuration>Connection>DS0 bundle +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 TS 0 1 0 0 0 0 0 0 0 0 0 TS 10 0 0 0 0 0 0 0 0 0 0 TS 20 0 0 0 0 0 0 0 0 0 0 TS 30 0 1.
Chapter 4 Configuration Installation and Operation Manual 4-24 Configuring IPmux-11 for Operation IPmux-11 Ver. 2.00 Configuration>Connection>Bundle connection TDM channel ID: 1 Bundle ID: 1 1. Destination IP address ... (0.0.0.0) 2. Outbound label tagging (Enable) 3.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Configuring IPmux-11 for Operation 4-25 2. From the Bridge menu, select Aging time and defi ne a period of time in seconds from the moment when a node is disconnected fro m the network segment or becomes inactive and remo val of the node ad dress from the database.
Chapter 4 Configuration Installation and Operation Manual 4-26 Configuring IPmux-11 for Operation IPmux-11 Ver. 2.00 Status: Enable (Adds the current port as a VLAN member) Disable (Disables VLAN membership of the current port) Configuration>Bridge 1.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Additional Tasks 4-27 4.4 Additional Tasks Displaying the IPmux-11 Inventory The IPmux-11 inventory displays informat ion on c urrent software and hardware revisions of the unit.
Chapter 4 Configuration Installation and Operation Manual 4-28 Additional Tasks IPmux-11 Ver. 2.00 2. From the Date/Time menu, select Set time , and enter the current time in t he hh:mm:ss format. 3. Select Set date , and enter the current date in the yyyy:mm:dd format.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Additional Tasks 4-29 Monitoring>Status>Diagnostics loopback Channel ID (1) Loopback state: > (Disable) > ESC-prev.menu; !-main menu; &-exit 1 Mngr/s Figure 4-30.
Chapter 4 Configuration Installation and Operation Manual 4-30 Additional Tasks IPmux-11 Ver. 2.00 Monitoring>Status>Eth Physical layer Channel > (Network-Eth1) Mode > (Full Duplex) Rate(Mbps) > (100) Status > (Connected) > F - forward ESC-prev.
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Additional Tasks 4-31 Sequence errors – total number of sequence errors o ccurred on the bundle Jitter buffer und.
Chapter 4 Configuration Installation and Operation Manual 4-32 Additional Tasks IPmux-11 Ver. 2.00 2. From the File Utilities , se lect Download/Upload using TFTP .
Installation and Operation Manual Chapter 4 Configuration IPmux-11 Ver. 2.00 Additional Tasks 4-33 Resetting IPmux-11 to the Defaults You can reset IPmux-11 t o its default setting s. The reset to the defaults does not affect the master clock setting.
Chapter 4 Configuration Installation and Operation Manual 4-34 Additional Tasks IPmux-11 Ver. 2.00.
IPmux-11 Ver. 2.00 Overview 5-1 Chapter 5 Configuring IPmux-11 for a Typical Application This chapter provides detailed instr uctions for setting up a typic al application using two IPmux-11 units.
Chapter 5 Configuring IPmux -11 for a Typical Application Installation and Op eration Manual 5-2 Configuring IPmux-11 Units IPmux-11 Ver. 2.00 Table 5-1. Configuration Summary Device E1 Parameters IP Parameters Bundle Parameters Bundle Connection IPmux-11 (A) • Transmit clock source: adaptive • Line type: Framed G.
Installation and Operation Manual Chapter 5 Co nfiguring IPmux-11 for a Typical Application IPmux-11 Ver. 2.00 Configuring IPmux-11 Units 5-3 To configure the manager list: 1.
Chapter 5 Configuring IPmux -11 for a Typical Application Installation and Op eration Manual 5-4 Configuring IPmux-11 Units IPmux-11 Ver. 2.00 Configuring Bund les To assign timeslots to a bundle: 1. Display the Connection menu ( Configuration > Connection ), and assign a number 1 to a bundle.
Installation and Operation Manual Chapter 5 Co nfiguring IPmux-11 for a Typical Application IPmux-11 Ver. 2.00 Configuring IPmux-11 Units 5-5 Configuration>Connection>Bundle connection 1. Destination IP address ... (192.168.10.1) 2. Next hop ...
Chapter 5 Configuring IPmux -11 for a Typical Application Installation and Op eration Manual 5-6 Configuring IPmux-11 Units IPmux-11 Ver. 2.00.
IPmux-11 Ver. 2.00 Monitoring Performance 6-1 Chapter 6 Troubleshooting and Diagnostics This chapter describes how to: • Monitor performance • Detect errors • Handle alarms • Troubleshoot problems • Perform diagnostic tests.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-2 Monitoring Performance IPmux-11 Ver. 2.00 To view the E1/T1 statistics: 1. From the Monitoring menu ( Figure 6-6 ), select Statistics . The Statistics menu appears. 2.
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Monitoring Performance 6-3 Table 6-1. E1/T1 Statistic s Alarm Description LOS Number of seco nds with Loss of Signal .
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-4 Monitoring Performance IPmux-11 Ver. 2.00 Table 6-1. E1/T1 Statistic s (Cont.) RAI (Yellow) Number of seconds with Remote Alarm Indica tors . A Remote Alarm Indicator is sent by a devi ce when it enters RED state (loses sync).
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Monitoring Performance 6-5 Table 6-1. E1/T1 Statistic s (Cont.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-6 Monitoring Performance IPmux-11 Ver. 2.00 Monitoring>Statistics>Bridge Channel > (User1-Eth2) Frames Received F.
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Monitoring Performance 6-7 Displaying Bundle Connection Statistics The Connection screen provides infor mation about the integrity of the TDMoIP connection, including the jitter buffer statistics.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-8 Monitoring Performance IPmux-11 Ver. 2.00 Table 6-2. Bundle Con nection Parameters Parameter Description Sequence Errors The number of seconds with at least one seque nce error since the last clear.
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Monitoring Performance 6-9 Table 6-2. Bundle Connection Parame ters (Cont.) Parameter Description Jitter Buffer Underflows The number of seconds with at least one jitter buffer underflow event since the last clear.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-10 Detecting Errors IPmux-11 Ver. 2.00 Table 6-2. Bundle Connection Parame ters (Cont.) Parameter Description Jitter Buffer Overflows The number of seconds with at least one jitter buffer overflow ev ent since the last clear.
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Detecting Errors 6-11 Diagnostics 1. Ping > 2. Loopback > 3. Trace route > 4. Self Test Results > > Please select item <1 to 4> ESC-prev.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-12 Detecting Errors IPmux-11 Ver. 2.00 Monitoring 1. Statistics > 2. Status > 3. Event Log > > Please select item <1 to 3> ESC-prev.menu; !-main menu; &-exit 1 Mngr/s Figure 6-6.
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Detecting Errors 6-13 Table 6-3. Event List Event Description Corrective Action COLD START IPmux-11 has b.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-14 Detecting Errors IPmux-11 Ver. 2.00 Table 6-3. Event List (Co nt.) Event Description Corrective Action LINE AIS END Lin.
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Handling Alarms 6-15 Configuring the Bundle Statistics Collection You can set the interval for the bundle statistics collection, as we ll the statistics threshold.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-16 Troubleshooting IPmux-11 Ver. 2.00 6.4 Troubleshooting The following table presents the event type s as they appear on the Event Log File and lists the actions required to co rrect the event (alarm) indication.
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Testing IPmux-11 6-17 6.5 Testing IPmux-11 Diagnostic capabilities of IPmux-11 include: • External loopbacks • Inband remote loopbacks for T 1 lines • Internal loopbacks • Pinging IP hosts • Running a trace route.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-18 Testing IPmux-11 IPmux-11 Ver. 2.00 To run a loopback: 1. From the Diagnostics menu ( Figure 6-4 ), select Loopback . The Loopback menu is displayed (see Figure 6-12 ).
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Testing IPmux-11 6-19 Activating T1 Inband Loopbacks T1 physical loopbacks ca n be activated by receiving a loopback activation c ode from TDM equipment connected to t he T1 port.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-20 Testing IPmux-11 IPmux-11 Ver. 2.00 • Define loop-up code length (Length of th e code to be sent by the TDM devic e i.
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Testing IPmux-11 6-21 Diagnostics>Ping 1. Destination IP address ... (0.0.0.0) 2. VLAN tagging (Enable) 3. VLAN ID[1 - 4095] ... (0) 4. VLAN priority[0 - 7] .
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-22 Frequently Asked Questions IPmux-11 Ver. 2.00 Diagnostics>Trace route 1. Destination IP address ... (0.0.0.0) 2. VLAN tagging (Enable) 3. VLAN ID[1 - 4095] ... (1) 4. VLAN priority tag [0 - 7] .
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Frequently Asked Questions 6-23 Framed mode: In case of local failure on t he IPmux, or situation of jitt.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-24 Frequently Asked Questions IPmux-11 Ver. 2.00 A configuration example: Setting IP precedence of 101 and IP ToS of 1000 will give us the byte 10110000, which means that the IPmux IP ToS parameter should be configured to 176 decimals.
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics IPmux-11 Ver. 2.00 Technical Support 6-25 6.7 Technical Support Technical support for this product can be obtained from the local distrib utor from whom it was purchased.
Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-26 Technical Support IPmux-11 Ver. 2.00.
IPmux-11 Ver. 2.00 E1 and T1 Connector A-1 Appendix A Connector Wiring A.1 E1 and T1 Connector Balanced Connector The E1 and T1 interfaces of IP mux-11 terminate in an 8-pin RJ-45 connecto r, wired in accordance with Table A-1 .
Appendix A Connector Wiring Installation and Operation Manual A-2 CONTROL Connector IPmux-11 Ver. 2.00 A.2 Ethernet Connectors The network and user Ethernet electrical interfaces terminate in 8-pi n RJ-45 connectors, wired in accordance with Table A-2 .
IPmux-11 Installation and Operation Manual Appendix A Connector Wiring IPmux-11 Ver. 2.00 External Clock Connector A-3 A.4 External Clock Connector The external clock interface terminates in an 8-pin RJ-45 conne ctor. Table A-4 lists the connector wiring.
Appendix A Connector Wiring Installation and Operation Manual A-4 External Clock Connector IPmux-11 Ver. 2.00.
IPmux-11 Ver. 2.00 Booting IPmux-11 B-1 Appendix B Boot Sequence and Downloading Software This appendix provides a description of the IPmux- 11 boot procedure vi a an ASCII terminal for downloading software. The file system can hold two compressed copies of the IPmux-11 code.
Appendix B Boot Sequence and Downloading Software Installation and Operation Manual B-2 Downloading the Application and Configuration Software IPmux-11 Ver.
Installation and Operation Manual Appendix B Boot Sequence and Downloading Software Downloading the Application and Configuration Software B-3 5. Send the software release file to IPmux -11 using the XMODEM utility of yo u terminal application.
Appendix B Boot Sequence and Downloading Software Installation and Operation Manual B-4 Downloading the Application and Configuration Software IPmux-11 Ver.
IPmux-11 Ver. 2.00 SNMP Environment C-1 Appendix C SNMP Management This appendix provides specific in format ion for IPmux-11 management by SNMP (Simple Network Management Protocol). The SNMP management functions of IPmux- 11 are provide d by an internal SNMP agent.
Appendix C SNMP Management Installation and Operation Manual C-2 SNMP Environment IPmux-11 Ver. 2.00 Management Information Base (MIB) The MIB includes a collection of managed ob jects. A managed o bject is defined as a parameter that can be managed, such as a performance statistics value.
Installation and Operation Manual Appendix C SNMP Management IPmux-11 Ver. 2.00 SNMP Environment C-3 MIBs Supported by the IPmux-11 SNM P Agent The interpretation of the relevant MIBs is a function of the SN MP agent of each managed entity. The general MIBs supporte d by the IPmux-11 SNMP agent are: • rfc1213.
Appendix C SNMP Management Installation and Operation Manual C-4 SNMP Environment IPmux-11 Ver. 2.00 SNMP Communities SNMP delimits management do mains by de fining commun itie s. Each community is identified by a name, which is an alphanumeric string of up to 255 charac ters defined by the user.
IPmux-11 Ver. 2.00 I-1 Index —A— AIS, 4-14 Alarms, 1-15, 6-15 Autonegotiation, 4-19 —B— Boot Boot manager, B-1 Bridge aging time, 4-25 configuration, 4-24 MAC table, 4-25 modes, 1-2, 1-17, 1-1.
Index Installation and Operation Manual I-2 IPmux-11 Ver. 2.00 —I— Inventory, 4-27 —J— Jitter buffer, 1-12, 6-9 , 6-10 depth, 1-12 max deviation, 6-10 time sinc e, 6-10 —L— LEDs, 3-1 Loopb.
Installation and Operation Manual Index IPmux-11 Ver. 2.00 I-3 environment, C-1 operations, C-1 Statistics bundles, 6-7 E1, 6-1 Ethernet, 6-5 T1, 6-1 Status bundles, 4-30 Diagnostics loopback, 4-28, 6.
Index Installation and Operation Manual I-4 IPmux-11 Ver. 2.00.
11 22 33 Front Panel 377-901-02/06 Supplement Drilling T emplate for W all Inst allation This panel is drawn to scale. T o drill the holes for a wall installation, tear this page out of the manual or print it and hold it against the wall. on letter-size paper (8.
.
24 Raoul W allenberg St., T el Av i v 69719, Israel T el: +972-3-6458181, F ax: +97 2-3-6483331, +972-3-6498250 E-mail: , W eb site: Customer Response Form RAD Data Communications would like your hel p in improving its product documentation. Please complete and return this form by mail or by fax or s end us an e-mail with your comments.
.
Error Report Type of Error(s) Incompatibility with product or Problem(s): Difficulty in understanding text Regulatory in formation (Safety, Compliance, Warnings, etc.) Difficulty in finding needed informat ion Missing information Illogical flow of information Style (spelling, grammar, references, etc.
.
.
Publication No. 352-20 0-08/06 www.rad.com INTERNATIONAL HEADQUARTER S: 24 Raoul Wallenberg Street, Tel Aviv 69719, Israel, Tel: 972-3-6458181 Fax: 972-3-6498250, 972-3-647 4436, Email: market@rad.com NORTH AMERICA HEADQUARTE RS: 900 Corporate Drive, Mahwah, N.
Ein wichtiger Punkt beim Kauf des Geräts RAD Data comm IPmux-11 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie RAD Data comm IPmux-11 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für RAD Data comm IPmux-11 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von RAD Data comm IPmux-11 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über RAD Data comm IPmux-11 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon RAD Data comm IPmux-11 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von RAD Data comm IPmux-11 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit RAD Data comm IPmux-11. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei RAD Data comm IPmux-11 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.