Benutzeranleitung / Produktwartung P9000 Series des Produzenten Printronix
Zur Seite of 334
P9000 Series Multifunction Printer User's Refer ence Manual R.
.
P9000 Series Multifuction Printer User's Refer ence Manual R P/N 133397–001, Rev B.
US and CANADA Radio Interference Note Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
i P9012 Multinational User's R eference Manual T ABLE OF CONTENTS Chapter P age 1 OVER VIEW Introduction 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P9012 Multinational User's R eference Manual ii 2 OPERA TION (continued) Setting F orms L ength 2-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T o Set F orms L ength in Inches 2-16 .
iii P9012 Multinational User's R eference Manual 5 VERTIC AL FORMAT UNITS Introduction 5-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P9012 Multinational User's R eference Manual iv 6 PROGRAMMING (continued) Special F unction Control Code - Control Code Header 6-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A ttribute Set and R eset Codes 6-3 .
v P9012 Multinational User's R eference Manual 6 PROGRAMMING (continued) Overscoring 6-54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Plot, Even Dot (P-Series High Density Graphics) 6-55 .
P9012 Multinational User's R eference Manual vi 9 RIBB ONMINDER Introduction 9-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview 9-1 .
vii P9012 Multinational User's R eference Manual About This Manual This manual has been written and formatted in a way to make it easy for you to use.
P9012 Multinational User's R eference Manual viii.
1-1 Overview CHAPTER 1 O VER VIEW Introduction The Printronix P9012 printer is a quiet, full-featured, multifunction line printer. In addition to the basic Printronix P-Series printer functions, the P.
Overview 1-2 n Built-in Diagnostic Self-T ests n RibbonMinder t F eature n Configuration P rintout n Data Stream Hex Code P rintout n R esident Serial and P arallel Interfaces n Downloadable Character.
1-3 Overview Character F ormation The P9012 printer generates characters by assembling groups of dots in matrices. Dots overlap to produce a solid appearing character (Figure 1-1). Dot impressions are made by an assem Ć bly of 88 hammers installed on an oscillating shuttle.
Overview 1-4 DOT ROW ST ART P APER ADVANCES P APER FEED P APER ADVANCES SP ACE 1 2 3 4 5 6 7 8 9 10 11 12 1 2 * ** USED FOR L OWERCASE DESCENDER ONL Y USED FOR UNDERLINE AND L OWERCASE DESCENDER * ** ONE CHARACTER ROW DIRECTION OF SHUTTLE MOVEMENT NOTE: P9012 SHUTTLE SWEEPS THROUGH 1.
1-5 Overview Plot Rate As well as character printing, the P9012 printer is capable of dot-addressable graphic plotting. Based on the protocol selected, either P-Series Plot Mode or Serial Matrix Bit Image Graph Ć ics is used; the plot rate specifications apply to both P-Series and Serial Matrix types of graph Ć ic plotting.
Overview 1-6.
2-1 Operation CHAPTER 2 OPERA TION Operation F eatures On Line The P9012 printer functions either on line" or off line." When on line, the printer is capable of receiving data and control commands from the host computer.
Operation 2-2 Yo u can also define and download an international language to allow any character within the character library to be substituted for any code. Similarly, an individual character in a font, or an entire set of characters, can be created and placed in a font.
2-3 Operation ON LINE CLEAR 6/8 LPI P APER ADV MENU UP MENU DOWN PREV NEXT RUN/ STOP ENTER PRINT CHECK 8 LPI VFU HOLD ENABLE REPRINT PA 1 CANCEL PA 2 AL T MODE F/L ALPHANUMERIC ON LINE LOADED MODE ST ATUS LAMPS MESSAGE DISPLA Y NOTE: THESE SWITCHES ARE VISIBLE ONL Y WITH THE PRINTER COVER OPEN PROVIDED WITH PI-3287 OPTION Figure 2-1.
Operation 2-4 CLEAR Switch and CHECK Indicator If a fault condition occurs, a fault message appears on the Message Display, and the CHECK indicator flashes alternately with the ON LINE indicator. P ress the CLEAR switch to indicate to the printer that a fault condition has been corrected.
2-5 Operation HOLD ENABLE , REPRINT P A1, CANCEL P A2, AL T MODE (Optional Switches) These four switches and their associated LEDs are included on printers equipped with a Printronix PI-3287 printer interface and operate independently of all other control panel switches.
Operation 2-6 The ENTER switch must be enabled (unlocked) before making configuration or format changes. Simultaneously pressing MENU UP and MENU DOWN alternately locks and unĆ locks the ENTER switch. (This sequence protects against accidental reconfiguration.
2-7 Operation Loading P aper The P9012 printer uses standard fanfold paper from 3 to 16 inches wide and 15 to 100 lb bond (0.025 inches thick maximum). T o load paper, perform the following steps and refer to Figure 2-2. 1. Place the printer off line and raise the printer cover.
Operation 2-8 Figure 2-2. Loading P aper.
2-9 Operation Setting T op-Of-F orm T op-of-form determines where the first line of print will appear and is set when paper is loaded. T ypically, the first line of print is set approximately one-half inch below the paper per Ć foration unless specific application requirements dictate otherwise.
Operation 2-10 Figure 2-3. Setting T op-of-F orm Setting T op-of-F orm - Reverse P aper Motion NOTE: Do not use this method of setting top-of-form for heavy forms or peel-off la Ć bel forms. 1. Place the printer off line and raise the printer cover. 2.
2-11 Operation P aper Stacking The printer can stack at least half a box of standard computer paper when the paper is properly loaded. After loading the paper, perform the following steps. 1. Open the rear cabinet door to access the paper stacking area.
Operation 2-12 NOTE 4: Check that the chains are properly installed (see Installation chapter) and that they engage the paper . Figure 2-4. F ront P aper F ence Installation.
2-13 Operation Figure 2-5. P aper T ent Installation Figure 2-6. P aper Stacking.
Operation 2-14 Unloading P aper 1. Place the printer off line and raise the printer cover. 2. T ear off the paper below the paper slot. 3. F ully raise the F orms Thickness A djustment L ever. 4. Open both tractor gates and remove the paper from the tractor sprockets.
2-15 Operation Figure 2-7. Ribbon R eplacement 7. Lower the F orms Thickness A djustment L ever (A) to the appropriate operating position. 8. Press CLEAR (on the control panel) to clear the PLA TEN OPEN fault condition. 9. Close the printer cover and place the printer on line.
Operation 2-16 Setting F orms Length NOTE: F orms length can also be set by control code from the host computer which will override the control panel setting. Using control codes, the host computer can specify forms lengths other than those available from the control panel.
2-17 Operation 2. P ress MENU DOWN to display the current forms length in lines. 3. Press NEXT or PREV to increase or decrease the forms length in 1-line increments, re Ć spectively. When the appropriate value is displayed, save it as described below.
Operation 2-18 F or additional printing capabilities and character attributes, refer to the Programming chapĆ ter. P rint mode control from the host will override the control panel setting. Setting Line Spacing P9012 printers can be set for a line spacing of 6, 8, or 10.
2-19 Operation 3. Press MENU DOWN, then repeatedly press NEXT or PREV until the PRINT D A T A STREAM IN HEX CODE message is displayed. 4. P ress MENU DOWN; the display will show OFFLINE HEX DUMP . 5. Press ON LINE. The display will indicate that the printer is on line and in hex dump mode.
Operation 2-20 F ault Condition Messages If a fault condition occurs in the printer, the CHECK light illuminates, the status lamps blink alternately, and the first line of the message display reads F A UL T CONDITION. If confiĆ gured, an alarm will sound when the F ault Condition occurs.
2-21 Operation Field Service R equired Printer problems requiring the attention of an authorized service representative also appear on the second line of the display and are indicated by an asterisk (.
Operation 2-22.
3-1 Configuration CHAPTER 3 CONFIGURA TION Introduction Configuration refers to the set of operating parameters that define how the printer communi Ć cates with the host computer. Most configuration parameters are selected from the control panel, as shown in the Control P anel Configuration Diagram at the end of this chapter.
Configuration 3-2 F rom the main configuration menus below, related configuration parameter values can be dis Ć played and selected. D Ribbon Life xxx% D Character Set D Application Compatibility D P.
3-3 Configuration Figure 3-1. Sample Configuration P rintout.
Configuration 3-4 F actory Default Configuration V alues Printronix factory default configuration values are shown in T able 3-1. These values are opera Ć tional when the printer is received. New values can be saved and applied as necessary for each application, but factory default values remain accessible using the LOAD P AR AMETERS menu.
3-5 Configuration Configuration P rocedure Most configuration options are selected from the control panel menu. T o change the configura Ć tion from the control panel, the printer must be powered up, off line (OFFLINE READ Y), and the control panel ENTER switch enabled (unlocked).
Configuration 3-6 Load Configuration V alues The previously saved default value set or the permanently stored Printronix factory value set can be loaded for use as needed. The following procedure provides a convenient method of resetting the printer configuration to a known value set.
3-7 Configuration Control P anel Configuration Diagram The Control P anel Configuration Diagram is a series of block diagrams that show the configu Ć ration menus and the parameters (values) available within each menu.
Configuration 3-8 Level III - Configuration Menu P arameters (Continued) A uto Line F eed P erforation Skip Define CR Code P aper Out Define LF Code PMD F ault VFU Select P rint W idth VFU T able (Sav.
3-9 Configuration CONTROL P ANEL ON LINE CLEAR 6/8 LPI P APER ADV MENU UP MENU DOWN PREV NEXT RUN/ STOP ENTER PRINT MESSAGE DISPLA Y CL = Press RS = Press PM = Press FL = Press CLEAR MENU DOWN MENU UP.
Configuration 3-10 ON LINE OFFLINE READY LEVEL I LEVEL II LEVEL III Print F ormat (Sheet 1) Main Configuration Menus (Sheet 2) P arameters (Sheets 3-17) DP AT 10 CPI , Factory print mode setting shown for illustration only . Print mode is an option set by the user .
Configuration 3–1 1 Control Panel Configuration Diagram (sheet 1 of 17) LEVEL I – PRINT FORMA T ON LINE LINE SP ACING SET AT 8 LPI LINE SP ACING SET AT 6 LPI OFFLINE READY PRINT MODE DP AT 10 CPI DP AT 12 CPI DP AT 13 CPI DP AT 15 CPI DP AT 17 CPI NLQ A T 10 CPI NLQ A T 12 CPI NLQ A T 15 CPI FORMS LENGTH RANGE IS FROM 1.
Configuration 3 – 12 OFFLINE READY ON LINE OL CHARACTER SET APPLICA TION COMP A TIBILITY P APER FORMAT HOST INTERF ACE SHEET 4 D LOAD P ARAMETERS U or CL U DIAGNOSTICS D SHEET 5 SHEET 8 SHEET 10 SHE.
Configuration 3 – 13 RIBBON LIFE xxx % D A FROM SHEET 2 CURRENT xxxx NEW RA TE xxxx CURRENT xxx NEW SIZE xxx STOP PRINTER AUD/VIS ALARM Control Panel Configuration Diagram (sheet 3 of 17) U N P NN N.
Configuration 3 – 14 Control Panel Configuration Diagram (sheet 4 of 17) CHARACTER SET B FROM SHEET 21 U U U SELECT SET SELECT SET SELECT SET P D P NN SELECT SUBSET SELECT SUBSET PRIMARY EXTENDED (1.
Configuration 3 – 15 D P APPLICA TION COMP A TIBILITY PRINTER PROTOCOL BUFFER SIZE C FROM SHEET 2 PRINTER PROTOCOL P – SERIES PRINTER PROTOCOL SERIAL MA TRIX BUFFER SIZE 2048 CHARACTERS BUFFER SIZ.
Configuration 3 – 16 P Control Panel Configuration Diagram (sheet 6 of 17) U U N SELECT SFCC CONTROL CODE 06 D 01 SOH * CONTROL CODE 06 10.3 LPI CONTROL CODE 06 8.
Configuration 3 – 17 P Control Panel Configuration Diagram (sheet 7 of 17) U U N OVERSTRIKE OVERSTRIKE DISABLE U U OVERSTRIKE ENABLE P N D N or P * Continued from sheet 6 CONTROL CODE 08 CONTROL COD.
Configuration 3 – 18 D P FROM SHEET 2 D P APER FORMA T AUTO LINE FEED AUTO LINE FEED DISABLE AUTO LINE FEED AFTER FULL LINE DEFINE CR CODE DEFINE CR CODE CR = CR DEFINE CR CODE CR = CR + LF DEFINE L.
Configuration 3 – 19 PERFORA TION SKIP PERFORA TION SKIP DISABLE PERFORA TION SKIP 1/2 INCH PERFORA TION SKIP 2/3 INCH PERFORA TION SKIP 5/6 INCH PERFORA TION SKIP 1 INCH P APER OUT P APER OUT IMMED.
Configuration 3 – 20 FROM SHEET 2 SHEET 1 1 FOR DA T APRODUCTS MENUS E D H SHEET 12 FOR SERIAL HOST INTERF ACE CENTRONICS DA T A BIT 8 DA T A BIT 8 ENABLE DA T A BIT 8 DISABLE F AST BUSY ENABLE DISABLE DA T A POLARITY ST ANDARD INVERTED F AST BUSY F AST BUSY DA T A POLARITY DA T A POLARITY ST ANDARD INVERTED RESP .
Configuration 3 – 21 FROM SHEET 10 D DA T A BIT 8 DA T A BIT 8 ENABLE DA T A BIT 8 DISABLE DISABLE ENABLE DA T A POLARITY ST ANDARD INVERTED H PI LINE PI LINE PI LINE DA T APRODUCTS Control Panel Configuration Diagram (sheet 1 1 of 17) DA T A POLARITY DA T A POLARITY ST ANDARD INVERTED RESP .
Configuration 3 – 22 D P PP P P N or P N or P I FROM SHEET 10 SERIAL RS – 232 P N P N P N P N P N PN PN P N PN P DA T A RA TE 150 BAUD 300 BAUD 600 BAUD 1200 BAUD 2400 BAUD 4800 BAUD 9600 BAUD WOR.
Configuration 3 – 23 U U U N N P P N P D P N P N P N D N or P D N or P BIT 8 FUNCTION FONT SELECT PI LINE IGNORE CD AND DSR DISABLE ENABLE CTS AND DSR DISABLE ENABLE Control Panel Configuration Diag.
Configuration 3 – 24 U N P DA T A TERM READY D P N P N P N P DA T A TERM RDY DA T A TERM RDY DA T A TERM RDY DA T A TERM RDY ONLINE AND BNF OFFLINE OR BF F ALSE TRUE Control Panel Configuration Diag.
Configuration 3 – 25 U P PP P P PRINTER TEST 8 INCH WIDTH PRINTER TEST FULL WIDTH RS RS RS RS PRINTER TEST PRINTER TEST PRINTER TEST PRINTER TEST SHIFT RECYCLE ALL E ’ S E PLUS TOF ALL H ’ S SHI.
Configuration 3 – 26 D P ARAMETERS P FROM SHEET 2 F LOAD P ARAMETERS P ARAMETERS E E LOAD IGP COMPLETED LOAD SA VED COMPLETED Control Panel Configuration Diagram (sheet 16 of 17) (1) (1) User define.
Configuration 3 – 27 U P FROM SHEET 15 N P D N P N U U U N P J PRINT ST A TISTICS POWER ON TIME XXXXX.X HRS PRINT TIME PRINT LINES PRINT P AGES XXXXX.
Configuration 3 – 28.
4-1 Graphics CHAPTER 4 GR APHIC S Introduction The printer can produce bit image graphics when in Serial Matrix protocol, and P-Series Plot Mode graphics when in P-Series protocol. Y ou can print text and graphics on the same line only by using the bit image protocol in Serial Matrix protocol.
Graphics 4-2 73 146 36 255 36 146 73 DECIMAL VAL UES 128 64 32 16 8 4 2 1 DECIMAL WEIGHTS 7th BIT IMAGE DA TA B YTE 2nd BIT IMAGE DA TA B YTE 1st BIT IMAGE DA TA B YTE Figure 4-1.
4-3 Graphics MSB MSB 87 6 54321 8 7 6 5 4 3 2 1 MSB : Most Significant Bit Figure 4-2. V ertical Data Byte P attern = A6 5 = MSB = ASCII CHARACTER DECIMAL VALU E BINARY CODE EQUIVALENT TO VERTICALL Y ROT ATED DA TA B YTE BIT IMAGE P ATTERN 128 64 32 16 8 4 2 1 Figure 4-3.
Graphics 4-4 the same as in the Single Density mode. Double horizontal density requires twice the number of input data bytes to print the same length line as for Single Density. P rintĆ ing double density reduces the printing speed by half. D Control code ESC Y selects the Double Speed, Double Density Mode .
4-5 Graphics At 60 dpi, Single Density = 792 bytes; Double Density = 1584 bytes Quadruple Density = 3168 bytes D Data in excess of the right margin is discarded. If the auto line feed is enabled, data in excess of the right margin will cause a Line F eed (LF) and continue printing on the next line.
Graphics 4-6 In Normal Density Plot : D The mode is selected with the odd dot plot control code ENQ (05 hex). D The odd-numbered dot columns are addressed to produce a horizontal and vertical density .
4-7 Graphics Plot Data Byte F ormat In P-Series Plot Mode, the format is as follows: D Each data byte specifies six out of twelve dot columns. D Using odd dot plot mode, bits 1 to 6 of the data byte address the odd-numbered dot columns; using even dot plot mode, bits 1 to 6 of the data byte address the even- numbered dot columns.
Graphics 4-8 Plot Data Line F ormat A plot data line may contain any number of plot data bytes up to the maximum of 132 for hori Ć zontal dot density of 60 dpi (Data P rocessing mode) or 198 bytes for a horizontal dot density of 90 dpi (Correspondence mode).
4-9 Graphics 3. Send the odd dot plot control code ENQ (05 hex) and a second line of data, followed by a line terminator. a. A line feed (0A hex) used as the line terminator causes the contents of the buffer to be plotted and the paper advances a single dot row , based on the vertical density of the current mode.
Graphics 4-10 Plotting the Data P-Series Plot Mode plots the image from the horizontal bit pattern. Figure 4-8 duplicates the pattern shown in Figure 4-4 but is modified for Odd Dot Plot. Eight dot rows are required, two characters per row, six columns per character.
Printr onix 4 – 11 Graphics T able 4–1. Plot Data Byte Dot Patterns 0100000 Space 0100001 0100010 010001 1 0100100 0100101 01001 10 01001 1 1 0101000 0101001 0101010 010101 1 0101 100 0101 101 010.
Graphics 4-12 T o Exit the P-Series Plot Mode When returning to the print mode from the P-Series Plot Mode, an extra line feed should be included in the data stream to maintain proper print line registration relative to the last line of plot graphics.
5-1 V ertical F ormat Units CHAPTER 5 VER TICAL FORMA T UNITS Introduction The P9012 printer includes four vertical format units: 1) Printronix standard Electronic V ertical F ormat Unit (EVFU), 2) Da.
V ertical F ormat Units 5-2 Line spacing may be mixed on the same form, but should be done with caution to avoid unpre Ć dictable results. VFU Deselected - If any VFU is deselected from the control panel, the VFU data is ignored and the forms length definition returns to the previously set value.
5-3 V ertical F ormat Units Channel 1 - The top-of-form code, reserved as the first line on the form or the first line printed (top-of-form position). The operating program sends the channel 1 code to advance to the top of the next form.
V ertical F ormat Units 5-4 T able 5-1. P-Series EVFU Codes - PI Line Enabled ASCII Channel Hex 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 6E PI 7 6 5 4 3 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X X X .
5-5 V ertical F ormat Units T able 5-2. P-Series EVFU Codes - PI Line Disabled or Not Used Hex 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 76 5 4 3 21 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0.
V ertical F ormat Units 5-6 1. The PI line must be enabled and set high; 2. Data bit 5 must be 1 (set); and 3. The EVFU must be the selected V ertical F ormat Unit. The Slew R elative configuration and the status of data bits 1-4 determine the number of lines slewed as described in T able 5-3.
5-7 V ertical F ormat Units Start Load Code - 6C, 6D , or 6E Hex 6E Hex - The D VFU start load code of 6E (hex) with the PI line high initiates the D VFU mem Ć ory load routine using the current printer line spacing as the D VFU line spacing.
V ertical F ormat Units 5-8 T able 5-4. DVFU Channel Assignment Channel # Bit # 6 5 4 3 2 - VT 1 - TOF 6 5 4 3 Channel # 2 1 (LSB) 12 - BOF 11 10 9 8 7 8 7 X (don't care) Second Data Byte First D.
5-9 V ertical F ormat Units T able 5-5. DVFU Channel Instruction ASCII Channel Hex 00 01 02 03 04 05 06 07 08 09 0A 0B PI 7 6 5 4 3 2 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X X X X X X X X X X X X X X X X X X .
V ertical F ormat Units 5-10 T able 5-6. P-Series D VFU Line Slewing ASCII Lines Slewed Hex PI 7 6 5 4 3 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X X X X X X X X X X X X X X X X X X X X X X X X X X 1 1 1 1.
5-11 V ertical F ormat Units Channel Assignment The NVFU memory has the capacity for 256-line forms. The first line identification code (channel code) in the memory load program defines the first line on the form; the second line identification code defines the second line on the form, etc.
V ertical F ormat Units 5-12 Using the NVFU The VFU LO ADED indicator on the control panel lights when the NVFU program has been enabled and loaded. Sending an appropriate channel code to the printer .
5-13 V ertical F ormat Units Relative Line Slewing Another method of moving paper using the PI line results in vertical slews of a specified num Ć ber of lines within the form relative to the current print line (rather than slewing to a specific line).
V ertical F ormat Units 5-14 A maximum of 12 channels can be assigned to one physical line on the form. T wo eight-bit data bytes (CVFU characters) are required per line.
5-15 V ertical F ormat Units Using the CVFU - 1F Hex The VFU LOADED indicator on the control panel lights when the CVFU program has been enabled and loaded.
V ertical F ormat Units 5-16 5. Bit 7 is low during the CVFU load. 6. A second start load code is received, resulting in reinitialization of the NVFU. (This alĆ lows the host data to be restarted.) When the CVFU memory is cleared, the forms length returns to the previously set value and the current print position becomes the top-of-form (TOF).
5-17 V ertical F ormat Units T able 5-12. CVFU Line Slewing Hex 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 76 5 4 3 21 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 .
V ertical F ormat Units 5-18 V ertical T ab P ositions V ertical tab positions are assigned to a line number. A maximum of 16 vertical tab positions can be assigned on the form.
6-1 Programming CHAPTER 6 PROGRAMMING Introduction The P9012 printer can be configured by from the control panel to respond to Printronix P-SeĆ ries or Serial Matrix control codes. This dual compatibility allows the programmer to choose one of two standard protocols.
Programming 6-2 Control Code Functions The following information is listed for each code function (where applicable and possible). ASCII Mnemonic - The standard A SCII name for the control code. Hex Code - The code's numeric equivalent in hexadecimal.
6-3 Programming Print format, print mode, or international language selection can be controlled by a longer se Ć quence known as a Command Line. Command Lines are string" type commands placed beĆ tween complete lines of text and affect the text which follows.
Programming 6-4 Control Code Reference Index The following index lists the control codes by function and lists the A SCII mnemonic and page number. Alphabetical listings by mnemonic and function are provided in Appendix D. NOTE: Some control code functions can be accomplished using another control code sequence or via control panel selection.
6-5 Programming PRINT MODE FUNCTION P-SERIES SERIAL P AGE NO . Bold P rint SFCC G ESC G 6-13 Bold P rint (1 line only) SFCC j 6-13 Bold P rint R eset SFCC H ESC H 6-14 Condensed P rint N/A SI 6-28 ESC.
Programming 6-6 OTHER FUNCTIONS (continued) FUNCTION P-SERIES SERIAL P AGE NO . Character Set Select (P rintable Symbols) N/A ESC u 6-24 Character Set Select: ECMA Extended SFCC OSET N/A 6-27 Characte.
6-7 Programming Backspace ASCII Hex Decimal P-Series/ Serial BS 08 08 Purpose Moves the logical print head to the left one character space toward the first character column.
Programming 6-8 Bell ASCII Hex Decimal P-Series/ Serial BEL 07 07 Purpose Sounds a buzzer/beeper. Comment The BEL function will sound a buzzer/beeper for 0.
6-9 Programming Bit Image Mode, Single Density ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC K 1B 4B 27 75 Purpose Selects Single (Normal) Density Bit Image graphics. Expression CHR$(27); ” K ” ;CHR$(n1);CHR$(n2); ” DA T A ” where n1 + 256 n2 define the number of data bytes to follow.
Programming 6-10 Bit Image Mode, Double Density ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC L 1B 4C 27 76 Purpose Selects Double Density Bit Image graphics. Expression CHR$(27); ” L ” ;CHR$(n1);CHR$(n2); ” DA T A ” where n1 + 256 n2 define the number of data bytes to follow.
6-11 Programming Bit Image Mode, Double Density Double Speed ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC Y 1B 59 27 89 Purpose Prints graphics at twice the speed of Double Density (same speed as Single Density) by ignoring adjacent dots.
Programming 6-12 Bit Image Mode, Quadr uple Density ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC Z 1B 5A 27 90 Purpose Selects Quadruple Density Bit Image graphics. Expression CHR$(27); ” Z ” ;CHR$(n1);CHR$(n2); ” DA T A ” where n1 + 256 n2 define the number of data bytes to follow.
6-13 Programming Bold P rint ASCII Hex Decimal P-Series SFCC G SFCC 47 SFCC 71 SFCC j (1 line) SFCC 6A SFCC 106 Serial ESC G 1B 47 27 71 Purpose Selects bold character printing. Comment When the bold character printing control code is received, all characters are printed in bold until reset by the bold print reset control code or printer reset.
Programming 6-14 Bold P rint R eset ASCII Hex Decimal P-Series SFCC H SFCC 48 SFCC 72 Serial ESC H 1B 48 27 72 Purpose R esets bold character printing. Comment The bold print reset control code only resets the bold print character attribĆ ute. Other print attributes such as double wide printing are not affected.
6-15 Programming Cancel ASCII Hex Decimal P-Series N/A N/A N/A Serial CAN 18 24 Purpose Clears the print buffer of all printable symbols since the last paper motion command was received. Comment This control code may be used as a delete line" function but should be used with extreme care to avoid possible misprinting.
Programming 6-16 Carriage Return ASCII Hex Decimal P-Series/ Serial CR 0D 13 Purpose Returns the logical print head to the first character column (resets the pointer to the first character position). Comment The CR code may or may not cause printing or paper motion, depending on the DEFINE CR CODE configuration parameter value.
6-17 Programming Character P itch 10 CPI ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC P 1B 50 27 80 Purpose Sets character pitch to 10 cpi. Comment Control Code ESC X can also be used to select a character pitch of 10 cpi. R efer to P rint Mode/P itch Selection on page 6-58.
Programming 6-18 Character P itch 12 CPI ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC M 1B 4D 27 77 ESC : 1B 3A 27 58 Purpose Sets character pitch to 12 cpi. Comment Control Code ESC X can also be used to select a character pitch of 12 cpi. R efer to P rint Mode/P itch Selection on page 6-58.
6-19 Programming Character Set Select ASCII Hex Decimal P-Series SFCC l xyz SFCC 6C xyz SFCC 108 xyz (lowercase L) Serial ESC l xyz 1B 6C xyz 27 108 xyz (lowercase L) Purpose Selects the character set, extended character set, and the international lanĆ guage for a specific character set.
Programming 6-20 T able 6-3. Extended Character Set Select (z) ECMA 94 0(30) 1(31) 2(32) 3(33) 4(34) IBM PC DEC Latin 1 Multinational Multinational Barcode 10 cpi IBM PC DEC Multinational Multinationa.
6-21 Programming Example The following example illustrates Character Set Select, where the character set is ECMA 94, the international language is Norwegian, and the extended character set is Scientific DP 10.
Programming 6-22 Character Set Select: 80-9F = Control Codes ASCII Hex Decimal P-Series SFCC 7 SFCC 37 SFCC 55 Serial ESC 7 1B 37 27 55 Purpose : Selects the character set wherein hex codes 80 to 9F are control codes. Also includes hex codes 03 to 06 and 15 in Serial Matrix printer protocol.
6-23 Programming Character Set Select: 80-9F = P rintable Symbols ASCII Hex Decimal P-Series SFCC 6 SFCC 36 SFCC 54 Serial ESC 6 1B 36 27 54 Purpose : Selects the character set wherein hex codes 80 to 9F are printable symbols. Also includes hex codes 03 to 06 and 15 in Serial Matrix printer protocol.
Programming 6-24 Character Set Select: 80-9F = P rintable Symbols ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC u 1B 75 27 117 Purpose : Selects the character set wherein hex codes 80 to 9F are printable symbols. Hex codes 03 to 06 and 15 are control codes.
6-25 Programming Character Set Select: International Languages ASCII Hex Decimal P-Series SFCC PSET ;n SFCC R n SFCC 52 n SFCC 82 n Serial ESC R n 1B 52 n 27 82 n Purpose Specifies the international l.
Programming 6-26 Character Set Select: International Languages (continued) Comment The international character set can also be selected from the control panel.
6-27 Programming Character Set Select: ECMA 94 Latin 1 Extended ASCII Hex Decimal P-Series SFCC OSET ;n Serial N/A N/A N/A Purpose Selects the Extended Character Set and the print mode and pitch at which the extended character will print. V alid only in the ECMA 94 Latin 1 Extended Character Set; otherwise, this command is ignored.
Programming 6-28 Condensed P rint ASCII Hex Decimal P-Series See Comment. Serial SI 0F 15 ESC SI 1B 0F 27 15 Purpose Selects 17 characters per inch (cpi) condensed print format. Comment Condensed print can be selected using P-Series control code SFCC X or by Serial Matrix control code ESC X.
6-29 Programming Condensed P rint R eset ASCII Hex Decimal P-Series N/A N/A N/A Serial DC2 12 18 Purpose Resets condensed character printing to 10 cpi. Comment The condensed print reset control code selects 10 cpi character pitch. Other print attributes are not affected.
Programming 6-30 Delete ASCII Hex Decimal P-Series N/A N/A N/A Serial DEL 7F 127 Purpose Deletes the previously received character on a line. Comment Characters that have been truncated due to line length restrictions are not af Ć fected by this code.
6-31 Programming Download a Language ASCII Hex Decimal P-Series SFCC V SFCC 56 SFCC 86 Serial ESC V 1B 56 27 86 Purpose T o define and download an international language character substitution taĆ ble which can be placed within the 224 printable symbol code points.
Programming 6-32 Download a Language (continued) Example The following sample program illustrates Downloading a L anguage. where: ESC V {2}E{65}E{224}E{66}E{225}E ESC V is the Serial Matrix Control Code Header introducing the Download a Language command.
6-33 Programming Download a Character ASCII Hex Decimal P-Series SFCC c SFCC 63 SFCC 99 Serial ESC c 1B 63 27 99 Purpose Defines a new character to replace any used or unused symbol point in the Character Library in a specific print mode and pitch.
Programming 6-34 Elongated (Double High) P rint (1 line) ASCII Hex Decimal P-Series SFCC h SFCC 68 SFCC 104 BS 08 08 Serial ESC h 1B 68 27 104 NOTE : SFCC h replaces SFCC d used in some previous Printronix firmware versions. Purpose Selects elongated (double high) character printing for one line only.
6-35 Programming Emphasized P rint ASCII Hex Decimal P-Series SFCC E SFCC 45 SFCC 69 Serial ESC E 1B 45 27 69 Purpose Selects emphasized character print format. Comment When the emphasized print control code is received, all characters will be printed in emphasized print until reset by the emphasized print reset control code or printer reset.
Programming 6-36 Emphasized P rint R eset ASCII Hex Decimal P-Series SFCC F SFCC 46 SFCC 70 Serial ESC F 1B 46 27 70 Purpose R esets emphasized character printing. Comment The emphasized print reset control code only resets the emphasized print character attribute.
6-37 Programming Expanded (Double Wide) Print ASCII Hex Decimal P-Series SFCC W n SFCC 57 n SFCC 87 n Serial ESC W n 1B 57 n 27 87 n Purpose Selects or resets expanded (double wide) print.
Programming 6-38 Expanded (Double Wide) Print (One Line Only) ASCII Hex Decimal P-Series SFCC k SFCC 6B SFCC 107 Serial SO 0E 14 ESC SO 1B 0E 27 14 Purpose Selects expanded (double wide) print for one line only.
6-39 Programming Extended Character Set ASCII Hex Decimal P-Series SO (Shift Out) 0E 14 SFCC SO SFCC 0E SFCC 14 SFCC n SFCC 6E SFCC 110 SFCC 4 SFCC 34 SFCC 52 Serial ESC 4 1B 34 27 52 Purpose Accesses the extended character set in the range A0 to FF hex using codes 20 to 7F hex.
Programming 6-40 Extended Character Set Cancel (Primary Character Set Select) ASCII Hex Decimal P-Series SI (Shift In) 0F 15 SFCC SI SFCC 0F SFCC 15 SFCC o SFCC 6F SFCC 111 SFCC 5 SFCC 35 SFCC 53 Seri.
6-41 Programming F orm F eed ASCII Hex Decimal P-Series/ Serial FF 0C 12 Purpose Prints the data in the buffer, advances the paper to the next top-of-form, and moves the printhead to the first character column. Comment The default forms length is determined by the configuration in nonvolatile memory.
Programming 6-42 F orms Length Set (Inches) ASCII Hex Decimal P-Series SFCC INCHES;n.f Serial ESC C NUL n 1B 43 0 n 27 67 0 n Purpose Sets the length of forms (paper) in inches. where n = whole numbers from 1 to 24 to specify the number of inches on a page.
6-43 Programming F orms Length Set (Lines) ASCII Hex Decimal P-Series SFCC LINES;n Serial ESC C n 1B 43 n 27 67 n Purpose Sets the length of a form (paper) in lines. where n = 1 to 192 (P-Series) or 1 to 127 (Serial) to specify the number of lines per page at the current line spacing.
Programming 6-44 Horizontal T ab ASCII Hex Decimal P-Series N/A N/A N/A Serial HT 09 09 Purpose Moves the logical printhead right to the next horizontal tab stop. Comment P ower-on default horizontal tabs are set at every eighth character in the Se Ć rial Matrix printer protocol.
6-45 Programming Horizontal T ab Set ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC D n 1B 44 n 27 68 n Purpose Sets up to 32 horizontal tab positions. Expression CHR$(27); ” D ” ;CHR$(n1);...CHR$(n32);CHR$(0); where n1 through n32 specify the character column of the tab positions.
Programming 6-46 Line F eed ASCII Hex Decimal P-Series/ Serial LF 0A 10 Purpose Prints the data in the buffer (if any) and advances the paper one line at the current line space setting. Comment If configured for LF equals newline (LF=CR+LF), the logical print head is positioned at character column 1 of the new line.
6-47 Programming Line F eed n/216 Inch (One Line Only) ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC J n 1B 4A n 27 74 n Purpose A dvances paper n/216 inch for one line only. where n = 1 to 255 Comment The n/216-inch line feed control code is effective for one line only.
Programming 6-48 Line Spacing 1/6 Inch ASCII Hex Decimal P-Series SFCC LPI;n SFCC 2 SFCC 32 SFCC 50 Serial ESC 2 1B 32 27 50 Purpose Sets line spacing to 6 lpi or as set by ESC A. Comment The value of n can be 6 or 8 only. In LPI mode using P-Series printer proto Ć col, if n = 6, this command sets line spacing to 1/6 inch.
6-49 Programming Line Spacing 1/8 Inch (8 lpi) ASCII Hex Decimal P-Series SFCC LPI;n SFCC 0 SFCC 30 SFCC 48 Serial ESC 0 1B 30 27 48 Purpose Specifies continuous line spacing at 1/8-inch increments (8 lpi).
Programming 6-50 Line Spacing 8 or 10.3 lpi (One Line Only) ASCII Hex Decimal P-Series AC K 0 6 0 6 SFCC f SFCC 66 SFCC 102 Serial N/A N/A N/A Purpose Selects line spacing of 1/8 or 7/72 inch for the current line only. Comment The default line spacing is reselected automatically after one line.
6-51 Programming Line Spacing 7/72 Inch ASCII Hex Decimal P-Series SFCC 1 SFCC 31 SFCC 49 Serial ESC 1 1B 31 27 49 Purpose Specifies the line spacing at 7/72-inch increments.
Programming 6-52 Line Spacing n/72 Inch ASCII Hex Decimal P-Series SFCC A n SFCC 41 n SFCC 65 n Serial ESC A n 1B 41 n 27 65 n Purpose Stores a line spacing of n/72-inch increments.
6-53 Programming Line Spacing n/216 Inch ASCII Hex Decimal P-Series SFCC 3 n SFCC 33 n SFCC 51 n Serial ESC 3 n 1B 33 n 27 51 n Purpose Specifies the line spacing at n/216-inch increments.
Programming 6-54 Overscoring ASCII Hex Decimal P-Series SFCC _ n SFCC 5F n SFCC 95 n Serial ESC _ n 1B 5F n 27 95 n Purpose Enables or disables automatic overscoring of all characters.
6-55 Programming Plot, Even Dot (P-Series High Density Graphics) ASCII Hex Decimal P-Series EOT 04 04 SFCC d SFCC 64 SFCC 100 Serial N/A N/A N/A Purpose P rints dots at the even numbered dot columns. Comment The even dot plot code is used for programming high density graphics and must be used in conjunction with the Odd Dot Plot code (05 hex).
Programming 6-56 Plot, Odd Dot (P-Series Normal Density Graphics) ASCII Hex Decimal P-Series ENQ 05 05 SFCC e SFCC 65 SFCC 101 Serial N/A N/A N/A Purpose P rints dots at the odd numbered dot columns. Comment This is the P-Series programming normal density graphics control code.
6-57 Programming P rinter Reset ASCII Hex Decimal P-Series SFCC @ SFCC 40 SFCC 64 Serial ESC @ 1B 40 27 64 Purpose Initializes all print mode related parameters to values previously saved. Comment When reset to the previously saved values, the current line is set to the top- of-form position.
Programming 6-58 P rint Mode/P itch Selection ASCII Hex Decimal P-Series SFCC PMODE;n SFCC X mn SFCC 58 mn SFCC 88 mn Serial ESC X mn 1B 58 mn 27 88 mn Purpose Selects the print mode (Data Processing, Correspondence, High Speed, or OCR) and character pitch in characters per inch (cpi).
6-59 Programming P rint Mode/P itch Selection (continued) T able 6-7. Character P itches A vailable by P rint Mode 0(30) 1(31) 2(32) PRINT Data Processing Correspondence High Speed MODE: 10 12 13.
Programming 6-60 P rinter Select ASCII Hex Decimal P-Series N/A N/A N/A Serial DC1 11 17 Purpose Places printer in the selected state. Comment When the configuration parameter PRINTER SELECT is enabled, this con Ć trol code will allow the printer to receive and print data from the host.
6-61 Programming P rinter Deselect ASCII Hex Decimal P-Series N/A N/A N/A Serial DC3 13 19 Purpose Places printer in the deselected state. Comment When the configuration parameter PRINTER SELECT is enabled, this con Ć trol code will disable the printer from receiving and printing data from the host.
Programming 6-62 RibbonMinder , Enable/Disable ASCII Hex Decimal P-Series SFCC r E SFCC 72 45 SFCC 114 69 SFCC r D SFCC 72 44 SFCC 114 68 Serial ESC r E 1B 72 45 27 114 69 ESC r D 1B 72 44 27 114 68 Purpose Enables or disables the RibbonMinder printer action.
6-63 Programming RibbonMinder , Set Job Rate ASCII Hex Decimal P-Series SFCC r J NNNN E SFCC 72 4A NNNN 45 SFCC 114 74 NNNN 69 Serial ESC r J NNNN E 1B 72 4A NNNN 45 27 114 74 NNNN 69 Purpose Sets printer job rate.
Programming 6-64 RibbonMinder , When W orn Action ASCII Hex Decimal P-Series SFCC r A S SFCC 72 41 53 SFCC 114 65 83 SFCC r A A SFCC 72 41 41 SFCC 114 65 65 SFCC r A V SFCC 72 41 56 SFCC 114 65 86 Ser.
6-65 Programming Skip-Over P erforation ASCII Hex Decimal P-Series N/A Serial ESC N n 1B 4E n 27 78 n Purpose Selects the number of lines (at the current line spacing) for the paper skip" at the bottom of the perforated page. where n = 1 to 127 to select the number of lines to skip.
Programming 6-66 Skip-Over P erforation Cancel ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC O (alpha O) 1B 4F n 27 79 n Purpose R esets skip-over perforation to zero.
6-67 Programming Superscript/Subscript Printing ASCII Hex Decimal P-Series SFCC S n SFCC 53 n SFCC 83 n Serial ESC S n 1B 53 n 27 83 n Purpose Selects superscript or subscript printing.
Programming 6-68 Superscript/Subscript Printing Reset ASCII Hex Decimal P-Series SFCC T SFCC 54 SFCC 84 Serial ESC T 1B 54 27 84 Purpose R esets superscript and subscript printing. Comment/ See the Superscript/Subscript control code example for an example of Example superscript/subscript reset.
6-69 Programming Underline ASCII Hex Decimal P-Series SFCC - n SFCC 2D n SFCC 45 n Serial ESC - n 1B 2D n 27 45 n Purpose Enables or disables automatic underlining of all characters.
Programming 6-70 VFU Commands (P-Series) ASCII Hex Decimal P-Series R efer to the V ertical F ormat Units chapter. Serial N/A N/A N/A NOTE: If the SFCC being used is ESC , the PI line must be set high when using the EVFU . Purpose L oad and execute the VFU.
6-71 Programming V ertical T ab ASCII Hex Decimal P-Series/ Serial VT 0B 11 Purpose Prints the data in the buffer and advances the paper to the next vertical tab position.
Programming 6-72 V ertical T ab Set/Clear (Serial Matrix) ASCII Hex Decimal P-Series N/A N/A N/A Serial ESC B n 1B 42 n 27 66 n Purpose Sets vertical tab positions. Expression CHR$(27); ” B ” ;CHR$(n);...CHR$(nk);CHR$(0); where n1 through nk specify the line number for the vertical tab(s), for a maxiĆ mum of 16 tab positions.
7-1 Interfaces CHAPTER 7 INTERF ACES Introduction The P9012 printer is equipped with resident parallel and serial interfaces. Only one interface can be enabled at a time via the control panel. An optional Dataproducts L ong Lines A dapter is available and replaces the Dataproducts and Centronics interface capability.
Interfaces 7-2 Data Strobe - A high true pulse from the host to indicate that data is ready. The data strobe must remain high at least until the Data R equest line goes false. Data Lines - Eight standard or inverted levels from the host that specify character data, plot data, or a control code.
7-3 Interfaces T able 7-2. Connector Pin Assignments for Dataproducts Interface with W inchester Connector (optional) SIGNAL PIN SIGNAL PIN Data Line 1 Data Line 2 Data Line 3 Data Line 4 Data Line 5 Data Line 6 Data Line 7 Data Line 8 P aper Instr.
Interfaces 7-4 maximum data line length (cable length) from the controller (host computer) to the printer is 40 feet. Centronics Interface Signals T able 7-3 lists the Centronics interface connector pin assignments. Centronics interface sigĆ nals between the computer and the printer are defined following the table.
7-5 Interfaces Centronics P arallel Interface Configuration The printer is configured according to the interface specified during printer configuration (re Ć fer to the Configuration chapter). If, however, the interface configuration parameters need to be changed, printer configuration is also user selectable.
Interfaces 7-6 150, 300, 600, 1200, 2400, 4800, 9600, 19200, or external control are available. Baud rates are selected from the control panel; external control is selected by jumper configuration on the DCU board as described in Appendix F , Hardware Jumper Configuration.
7-7 Interfaces Data T erminal R eady (DTR) - Control signal from the printer. Subject to configuration. RS-232 Serial Interface P rotocols The following serial interface protocol characters are available. The protocol can be confiĆ gured from the control panel to meet host interface requirements.
Interfaces 7-8 n Input Buffer Size (selected from the Application Compatibility menu; refer to the Configuration chapter) n Data P rotocol of hardware (DTR, R everse Channel [R C], or R TS), X-ON/X-OF.
8-1 R outine Service & Diagnostics CHAPTER 8 ROUTINE SER VICE & DIAGNOSTIC S Introduction The P9012 printer requires little maintenance other than regular general cleaning. P eriodically remove excess paper chaff and dust from the ribbon and paper paths.
R outine Service & Diagnostics 8-2 quality. Most paper chaff accumulates around the ends of the platen and ribbon path. An opĆ tional cleaning kit is available from your authorized Printronix representative. T o clean the inĆ terior of the printer, perform the following steps and refer to Figure 8-1.
8-3 R outine Service & Diagnostics Figure 8-1. Interior Cleaning 10. Using a soft cloth lightly moistened with alcohol, remove ink or dirt from the platen.
R outine Service & Diagnostics 8-4 Figure 8-2. Cleaning the P aper Motion Detector.
8-5 R outine Service & Diagnostics P rinter Self-T ests The printer contains several self-tests that are helpful in evaluating and maintaining optimum printer performance. Each of these tests may be initiated from the DIAGNOSTICS/ PRINTER TEST 8 INCH WIDTH or DIA GNOSTICS/PRINTER TEST FULL WIDTH con Ć figuration menus.
R outine Service & Diagnostics 8-6 4. T o select one of the 8 INCH WIDTH or FULL WIDTH paper tests, press MENU DOWN then repeatedly press NEXT or PREV until the appropriate test is displayed. T ests inĆ clude shift recycle, all Es, and others. 5.
8-7 R outine Service & Diagnostics 6. Send the data from the host; the hex dump will print. 7. Press ON LINE again to stop the hex dump. The display will read OFFLINE HEX DUMP . 8. Press CLEAR to return printer to OFFLINE READ Y. 9. Close printer cover and place the printer on line.
R outine Service & Diagnostics 8-8 T able 8-1. F ault Messages F ault Displayed Operator Correctable? Explanation Corrective Action F AUL T CONDITION P APER OUT Y es Paper out Add paper . FAU L T CONDITION PLA TEN OPEN Y es Platen open Close platen (F orms Thickness Adjustment Lever).
9-1 RibbonMinder CHAPTER 9 R IBB ON M INDER T Introduction The RibbonMinder (patent pending) ensures quality printing by determining when a ribbon should be changed. The RibbonMinder monitors ink consumption by analyzing printer hamĆ mer action. It is designed to alert the operator before the print quality falls below a certain level.
9-2 RibbonMinder The RibbonMinder feature detects when no usable ink remains. The message display will indi Ć cate 0% and the printer will alert you. At this point, the printer is typically configured to stop printing, declare a RIBBON F AU L T , and display a CHANGE RIBBON message.
9-3 RibbonMinder appears on the display. Press MENU DOWN to display ACTION ENABLE. Each time NEXT is pressed at this level, the function will alternate between ENABLE and DISĆ ABLE. P ress ENTER. If the asterisk does not appear, refer to Application Hints on page 9-12.
9-4 RibbonMinder display. P ress DOWN and then NEXT until the desired ribbon size is displayed. The RIB Ć BON SIZE is the actual capacity of the ribbon. The most common ribbon size is 60 yards long with a spool diameter of approximately 4 inches. If, for example, the new ribbon is 100 yards long, the capacity value is 100.
9-5 RibbonMinder ANAL YZE JOB NEW R A TE 400 P ress ENTER to enter this rate as the new job rate. The message display will read: CURRENT 400 NEW R A TE 400 11. R eplace W orn Ribbon Install a new ribbon once the ribbon becomes worn. P ress CLEAR to clear the PLA TEN OPEN fault message.
9-6 RibbonMinder 2. Unlock the Control P anel If not at the OFFLINE READ Y prompt, press CLEAR until OFFLINE READ Y apĆ pears. Unlock the printer configuration by simultaneously pressing MENU UP and MENU DOWN until the ENTER SWITCH UNLOCKED prompt appears briefly in the display.
9-7 RibbonMinder RIBBON LIFE 100% STOP PRINTER * T o select the A UDIO/VISU AL ALARM action when the ribbon is worn, press NEXT ; when A UD/VIS ALARM is displayed, press ENTER. RIBBON LIFE 100% A UD/VIS ALARM * T o select the VISU AL ALARM action, press NEXT ; when VISU AL ALARM is displayed, press ENTER.
9-8 RibbonMinder gresses. The ribbon life will decrease as the ribbon consumes ink. The following example illustrates the display as the job progresses: ON LINE 95% DP A T 10 CPI 10. When Ribbon Life Reaches 0% Printing can continue until the remaining usable ink reaches 0%.
9-9 RibbonMinder 2. Enter SET JOB R ATE mode F rom OFFLINE READ Y, press MENU DOWN to enter the RIBBON LIFE menu. Press NEXT to enter the SET JOB R A TE. The CURRENT V AL UE at this point corre Ć sponds to the previous job. CURRENT NEW R A TE 375 375 * 3.
9-10 RibbonMinder 2. Reset for New Ribbon Press ENTER to reset for a new ribbon. The display message will indicate CHANGE RIBBON. RIBBON LIFE CHANGE RIBBON 100% 3. Install New Ribbon Install a new ribbon and press CLEAR to clear any fault conditions that occurred while changing the ribbon.
9-11 RibbonMinder SET JOB RA TE Command: SFCC r J NNNN E where - NNNN is the JOB R A TE value between 0 and 1000 expressed as a decimal number having between one and four digits. Each individual digit of the value is represented by the corresponding hex code.
9-12 RibbonMinder Application Hints D To decrease a value in the menu, press PREV . D P arameters cannot be changed from the control panel while the printer configuration is locked. The ENTER SWITCH LOCKED message will appear briefly if you attempt to change a parameter while the ENTER switch is locked.
RibbonMinder 9 – 13 RIBBON LIFE xxx % D CURRENT xxxx NEW RA TE xxxx CURRENT xxx NEW SIZE xxx STOP PRINTER AUD/VIS ALARM RibbonMinder Diagram U N P NN N RIBBON LIFE xxx % RIBBON LIFE xxx % RIBBON LIF.
RibbonMinder 9 – 14.
10-1 Multinational Character Sets CHAPTER 10 MUL TINA TIONAL CHAR ACTER SETS Introduction F our basic character set choices are available and selected from the control panel: IBM PC, Multinational, DEC Multinational, and ECMA 94 L atin 1 which includes an extended charac Ć ter set.
Multinational Character Sets 10-2 The selection of the Extended Character Set also sets the print mode and pitch at which the Extended Character Set is printed.
Multinational Character Sets 10 – 3 Multinational Character Set Diagram CHARACTER SET U U U SELECT SET SELECT SET SELECT SET P D P NN SELECT SUBSET SELECT SUBSET PRIMARY EXTENDED (1) IBM PC MUL TINA.
Multinational Character Sets 10-4 Character Address T able (Character Library) 00 0_ 0 1 2 3 4 5 6 7 8 9 A B C D E F 00 1_ 00 2_ 00 3_ 00 4_ 00 5_ 00 6_ 00 7_ 00 8_ 00 9_ 00 A_ 00 B_ 00 C_ 00 D_ 00 E_ Ï ¨ Í Á Ó Ú ý Ý Ø À Ù | ø È Ì ¶ § Ò ! i + ' - .
10-5 Multinational Character Sets NOTE: Not all characters are available in all print modes. A 01 0_ 01 D_ 00 F_ 01 1_ 01 2_ 01 3_ 01 4_ 01 5_ 01 6_ 01 7_ 01 8_ 01 9_ 01 A_ 01 B_ 01 C_ 01 E_ @ n ; Ë Â Ê i # Î Ô Û ¾ ! ® 0 T Y g e z h W a e h u u w D u .
Multinational Character Sets 10-6 Numeric Character Location Listing The complete character library is listed below, arranged in numeric order by hexadecimal adĆ dress.
10-7 Multinational Character Sets 0026 0038 Ampersand 0027 0039 Single Quote 0028 0040 L eft P arenthesis 0029 0041 Right P arenthesis 002A 0042 Asterisk 002B 0043 Plus Sign 002C 0044 Comma 002D 0045 .
Multinational Character Sets 10-8 0052 0082 Uppercase R 0053 0083 Uppercase S 0054 0084 Uppercase T 0055 0085 Uppercase U 0056 0086 Uppercase V 0057 0087 Uppercase W 0058 0088 Uppercase X/Chi 0059 008.
10-9 Multinational Character Sets 007E 0126 Tilde 007F 0127 Caron 0080 0128 Uppercase C with Cedilla 0081 0129 L owercase U with Umlaut 0082 0130 L owercase E with A cute A ccent Mark 0083 0131 L ower.
Multinational Character Sets 10-10 00AA 0170 Not Sign 00AB 0171 F raction One Half 00A C 0172 F raction One Quarter 00AD 0173 Inverted Exclamation Mark 00AE 0174 L eft Angle Quote 00AF 0175 Right Angl.
10-11 Multinational Character Sets (continued) 00CE 0206 Graphics Bar Double Left to Right Double T op to Bottom 00CF 0207 Graphics Bar Double L eft to Right T op to Center 00D0 0208 Graphics Bar L ef.
Multinational Character Sets 10-12 (continued) 00F9 0249 Big Dot 00F A 0250 Small Dot 00FB 0251 R adical Symbol 00FC 0252 Superscript L owercase N 00FD 0253 Superscript 2 00FE 0254 Small Square 00FF 0.
10-13 Multinational Character Sets (continued) 0125 0293 L owercase Epsilon with R ough 0126 0294 L owercase Eta with R ough 0127 0295 L owercase Iota with R ough 0128 0296 L owercase Iota with Umlaut.
Multinational Character Sets 10-14 (continued) 0151 0337 L eft Improper Subset Symbol 0152 0338 Bi-Implicative Symbol 0153 0339 F or All Symbol 0154 0340 F or Some Symbol 0155 0341 Uppercase Epsilon i.
10-15 Multinational Character Sets (continued) 017D 0381 White Hex Symbol 017E 0382 White Square Symbol 017F 0383 T riangle Symbol 0180 0384 P oint to Bottom Symbol 0181 0385 P oint to Right Symbol 01.
Multinational Character Sets 10-16 (continued) 01A9 0425 Bar Code 1F 01AA 0426 Bar Code 20 01AB 0427 Bar Code 21 01A C 0428 Bar Code 22 01AD 0429 Bar Code 23 01AE 0430 Bar Code 24 01AF 0431 Bar Code 2.
10-17 Multinational Character Sets 01D5 0469 L owercase OE Ligature 01D6 0470 Asterisk with Overline 01D7 0471 Black Out Box 01D8 0472 Uppercase Y with Umlaut 01D9 0473 L owercase E with T ilde 01D A .
Multinational Character Sets 10-18 Alphabetical Character Location Listing The complete character library is listed below, arranged in alphabetical order by the symbol's technical name. Included are the hexadecimal and decimal values for each symbol.
10-19 Multinational Character Sets (continued) 01A7 0423 Bar Code 1D 01A8 0424 Bar Code 1E 01A9 0425 Bar Code 1F 01AA 0426 Bar Code 20 01AB 0427 Bar Code 21 01A C 0428 Bar Code 22 01AD 0429 Bar Code 2.
Multinational Character Sets 10-20 (continued) 01D3 0467 Bar Code 49 00F9 0249 Big Dot 0152 0338 Bi-Implicative Symbol 0005 0005 Black Club 0004 0004 Black Diamond 0003 0003 Black Heart 01D7 0471 Blac.
10-21 Multinational Character Sets (continued) 0184 0388 Fixed Star Symbol 0153 0339 F or All Symbol 0154 0340 F or Some Symbol 01E3 0483 F ork 0034 0052 F our 0173 0371 F raction F our Fifths 01DC 04.
Multinational Character Sets 10-22 (continued) 00CC 0204 Graphics Bar Double Right to Center Double T op to Bottom 00C8 0200 Graphics Bar Double Right to Center Double T op to Center 00C6 0198 Graphic.
10-23 Multinational Character Sets (continued) 0018 0024 International Currency Symbol 00EF 0239 Intersection Symbol 00AD 0173 Inverted Exclamation Mark 00A8 0168 Inverted Question Mark 0186 0390 Junc.
Multinational Character Sets 10-24 (continued) 0138 0312 L owercase Eta 0126 0294 L owercase Eta with R ough 001A 0026 L owercase Eth 0066 0102 L owercase F 015F 0351 L owercase F in Script 0067 0103 .
10-25 Multinational Character Sets (continued) 00ED 0237 L owercase Phi Script 00E3 0227 L owercase P i 0145 0325 L owercase P si 0071 0113 L owercase Q 0072 0114 L owercase R 013F 0319 L owercase Rho.
Multinational Character Sets 10-26 (continued) 0000 0000 Overline 0014 0020 P aragraph Sign 0161 0353 P arallel Symbol 0179 0377 P er Symbol 0025 0037 P ercent Sign 002E 0046 Period 0162 0354 P erpend.
10-27 Multinational Character Sets (continued) 00FC 0252 Superscript L owercase N 010A 0266 Superscript 1 00FD 0253 Superscript 2 010B 0267 Superscript 3 014D 0333 Therefore Symbol 0033 0051 Three 007.
Multinational Character Sets 10-28 (continued) 01E9 0489 Uppercase I Right Underline 011E 0286 Uppercase I P rime with Bar 000B 0011 Uppercase I with A cute A ccent Mark 0102 0258 Uppercase I with Cir.
10-29 Multinational Character Sets 0019 0025 Uppercase Thorn 0055 0085 Uppercase U 000D 0013 Uppercase U with A cute A ccent Mark 0104 0260 Uppercase U with Circumflex 0017 0023 Uppercase U with Grave.
Multinational Character Sets 10-30.
11-1 Installation CHAPTER 11 INST ALLATION Introduction This chapter explains P9012 printer installation procedures. The following topics are covered: n P ower R equirements n Site R equirements n Shi.
Installation 11-2 A label on the back of the printer near the power cord indicates the voltage and frequency re Ć quirements. The printer must be connected to the specified power source, either 110, 220 or 240 volts at 50 to 60 Hz. Line voltage can vary 10%.
11-3 Installation Figure 11-1. Site R equirements Shipping Restraints During shipping, the printer mechanism is protected by foam packing and removable tie wraps which secure the Forms Thickness Adjustment L ever, P aper Guide, F ront P aper Fence, and P aper T ent.
Installation 11-4 Figure 11-2. Shipping R estraint Removal.
11-5 Installation P aper Stacking Chain Assembly Installation The Paper Stacking Chain Assembly is used on the printer to ensure correct paper flow and stacking. T o install the Chain Assembly, perform the following steps and refer to Figure 11-3. 1. If paper is loaded in the printer, unload the paper (refer to the Operation chapter).
Installation 11-6 Cable Connections P erform the following steps and refer to Figure 11-4 to connect the cables to the printer. 1. V erify that the site line voltage is within the same range as that shown on the printer ID label (A) and that the proper power cord has been selected.
11-7 Installation P reliminary T est The printer is now ready for a preliminary test. The following steps define the test procedure. Control panel and Message Display features are explained in the Operation chapter. 1. Set the A C power switch to ON. 2.
Installation 11-8.
A-1 Appendix APPENDIX A ST ANDARD ASCII CHAR ACTER CHAR T KEY ASCII CHARACTER ESC 33 27 1B OCT AL DECIMAL HEX B7 0 0 0 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 .
P9000 Appendices 10-A-2.
B-1 Appendix APPENDIX B CHARACTER SETS Introduction The character set charts in this Appendix provide the hexadecimal character address matrices for each character set and international language. F or example, if the IBM PC Character Set and US A SCII Language is selected, 0023 hex selects the Number Sign (#).
Appendix B-2 IBM PC Primary Character Set P-Series Emulation (80-9F=Control Codes) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2 3 4 5 6 7 8 9.
B-3 Appendix IBM PC Extended Set P-Series Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 203 131 83 204 132.
Appendix B-4 IBM PC Primary Character Set P-Series Emulation (80-9F=Printable Symbols) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2 3 4 5 6 7.
B-5 Appendix IBM PC Extended Set P-Series Emulation (80-9F=Printable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 203 131 83 204.
Appendix B-6 IBM PC Primary Character Set Serial Matrix Emulation (80-9F=Control Codes) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2 3 4 5 6 .
B-7 Appendix IBM PC Extended Set Serial Matrix Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 203 131 83 20.
Appendix B-8 IBM PC Primary Character Set Serial Matrix Emulation (80-9F=P rintable Symbols) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2 3 4.
B-9 Appendix IBM PC Extended Set Serial Matrix Emulation (80-9F=P rintable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 203 131 .
Appendix B-10 IBM PC International Languages Substitution T able LANGU AGE ASCII F rench German English Danish Swedish Italian Spanish Japanese F rench Canadian Example: 005B = [ in ASCII 005B = Æ in.
B-11 Appendix Multinational Character Set Charts D Primary Character Set P-Series Emulation (80-9F Control Codes) P age B-2 D Extended Character Set P-Series Emulation (80-9F Control Codes) P age B-3 .
Appendix B-12 Multinational P rimary Character Set P-Series Emulation (80-9F=Control Codes) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2 3 4 .
B-13 Appendix Multinational Extended Set P-Series Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 203 131 83.
Appendix B-14 Multinational P rimary Character Set P-Series Emulation (80-9F=Printable Symbols) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2 .
B-15 Appendix Multinational Extended Set P-Series Emulation (80-9F=Printable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 203 13.
Appendix B-16 Multinational P rimary Character Set Serial Matrix Emulation (80-9F=Control Codes) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2.
B-17 Appendix Multinational Extended Set Serial Matrix Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 203 1.
Appendix B-18 Multinational P rimary Character Set Serial Matrix Emulation (80-9F=P rintable Symbols) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 .
B-19 Appendix Multinational Extended Set Serial Matrix Emulation (80-9F=P rintable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 .
Appendix B-20 Multinational P rimary Character Set in OCR-A B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 0 .
B-21 Appendix Multinational Extended Character Set in OCR-A 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 203 131 83 204 132 84 205 133 85.
Appendix B-22 Multinational P rimary Character Set in OCR-B B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 0 .
B-23 Appendix Multinational Extended Character Set in OCR-B 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 203 131 83 204 132 84 205 133 85.
Appendix B-24 Multinational International Languages Substitution T able LANGU AGE ASCII EBCDIC Example: 005B = [ in ASCII 005B = ¢ in EBCDIC Hex Address 005B 005D 005E []^ | : ¢.
B-25 Appendix ECMA-94 Latin 1 Character Set Charts P-Series Emulation (80-9F=Control Codes) D P rimary Character Set P age B-26 D European Extended Character Set: Barcode P age B-27 D European Extende.
Appendix B-26 ECMA-94 Latin 1 P rimary Character Set P-Series Emulation (80-9F=Control Codes) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2 3 .
B-27 Appendix ECMA-94 Latin 1 European Extended Set: Barcode P-Series Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 2.
Appendix B-28 ECMA-94 Latin 1 European Extended Set: Multinational P-Series Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 12.
B-29 Appendix ECMA-94 Latin 1 European Extended Set: Greek P-Series Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202.
Appendix B-30 ECMA-94 Latin 1 European Extended Set: Graphics P-Series Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 .
B-31 Appendix ECMA-94 Latin 1 European Extended Set: Scientific P-Series Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 8.
Appendix B-32 ECMA-94 Latin 1 Primary Character Set P-Series Emulation (80-9F=Printable Symbols) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2.
B-33 Appendix ECMA-94 Latin 1 European Extended Set: Barcode P-Series Emulation (80-9F=Printable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 .
Appendix B-34 ECMA-94 Latin 1 European Extended Set: Multinational P-Series Emulation (80-9F=Printable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 20.
B-35 Appendix ECMA-94 Latin 1 European Extended Set: Greek P-Series Emulation (80-9F=Printable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81.
Appendix B-36 ECMA-94 Latin 1 European Extended Set: Graphics P-Series Emulation (80-9F=Printable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129.
B-37 Appendix ECMA-94 Latin 1 European Extended Set: Scientific P-Series Emulation (80-9F=Printable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 1.
Appendix B-38 ECMA-94 Latin 1 Primary Character Set Serial Matrix Emulation (80-9F=Control Codes) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 .
B-39 Appendix ECMA-94 Latin 1 European Extended Set: Barcode Serial Matrix Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129.
Appendix B-40 ECMA-94 Latin 1 European Extended Set: Multinational Serial Matrix Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 2.
B-41 Appendix ECMA-94 Latin 1 European Extended Set: Greek Serial Matrix Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 8.
Appendix B-42 ECMA-94 Latin 1 European Extended Set: Graphics Serial Matrix Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 12.
B-43 Appendix ECMA-94 Latin 1 European Extended Set: Scientific Serial Matrix Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 .
Appendix B-44 ECMA-94 Latin 1 Primary Character Set Serial Matrix Emulation (80-9F=P rintable Symbols) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1.
B-45 Appendix ECMA-94 Latin 1 European Extended Set: Barcode Serial Matrix Emulation (80-9F=P rintable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 20.
Appendix B-46 ECMA-94 Latin 1 European Extended Set: Multinational Serial Matrix Emulation (80-9F=P rintable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128.
B-47 Appendix ECMA-94 Latin 1 European Extended Set: Greek Serial Matrix Emulation (80-9F=P rintable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 .
Appendix B-48 ECMA-94 Latin 1 European Extended Set: Graphics Serial Matrix Emulation (80-9F=P rintable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 2.
B-49 Appendix ECMA-94 Latin 1 European Extended Set: Scientific Serial Matrix Emulation (80-9F=P rintable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80.
Appendix B-50 ECMA-94 Latin 1 International Languages Substitution T able LANGU AGE ASCII Example: 005B = [ in ASCII 005B = Æ in Danish Hex Address 0021 0022 0023 0024 0040 005B 005C 005D 005E 0060 #.
B-51 Appendix DEC Multinational Character Set Charts D Primary Character Set P-Series Emulation (80-9F Control Codes) P age B-52 D Extended Character Set P-Series Emulation (80-9F Control Codes) P age.
Appendix B-52 DEC Multinational P rimary Character Set P-Series Emulation (80-9F=Control Codes) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 1 2 .
B-53 Appendix DEC Multinational Extended Set P-Series Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 203 13.
Appendix B-54 DEC Multinational P rimary Character Set P-Series Emulation (80-9F=Printable Symbols) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0 .
B-55 Appendix DEC Multinational Extended Set P-Series Emulation (80-9F=Printable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 20.
Appendix B-56 DEC Multinational P rimary Character Set Serial Matrix Emulation (80-9F=Control Codes) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3 B1 0.
B-57 Appendix DEC Multinational Extended Set Serial Matrix Emulation (80-9F=Control Codes) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130 82 2.
Appendix B-58 DEC Multinational P rimary Character Set Serial Matrix Emulation (80-9F=P rintable Symbols) B 7 000 0 1 1 1 1 B6 0 B5 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 0 1 2 3 45 67 BITS ROW B4 B2 B3.
B-59 Appendix DEC Multinational Extended Set Serial Matrix Emulation (80-9F=P rintable Symbols) 000 0 1 1 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 COLUMN 8 9 10 11 12 13 14 15 200 128 80 201 129 81 202 130.
Appendix B-60 DEC Multinational International Languages Substitution T able LANGU AGE ASCII Example: 005B = [ in ASCII 005B = Æ in Danish Hex Address 0023 # £ @ É [ Æ Ä Ø N ~ ¥ ] § ^ e ¿ ^ {.
C-1 Appendix APPENDIX C SPECIFICA TIONS P rinting Characteristics Printer throughput, in lines per minute (LPM), is a factor of the selected print mode. The P9012 nominal print rates are listed in T able C-1 on page C-2, and assume a tolerance of 5% and an adequate input data rate.
Appendix C-2 T able C-1. P9012 Print Rates PERFORMANCE PL OT MODE UPPERCASE ONL Y UPPER & L OWERCASE LPM LPM IPM PRINT APPLICATION DOT DENSITY (DPI) H X V NOTE Ă CHARACTERS PER INCH DOT MATRIX NOTE CORRESPONDENCE 90 (180) X 96 10 12 15 7 (13) X 9 + 3 6 (11) X 9 + 3 5 (9) X 9 + 3 480 370 50 DAT A PROCESSING 60 (120) X 72 10 12 13.
C-3 Appendix Relative Humidity Operating 10% to 90% (noncondensing) Storage 5% to 95% (noncondensing) Acoustic Noise Less than 55 dBA (tested at 132 column, DP at 10 cpi per ISO 7779) Electrical Chara.
Appendix C-4 Interfaces T ype R esident parallel and serial L ogic L evels TTL/RS-232 Data F ormat ASCII Compatibility Centronics, Dataproducts, RS-232C Buffer Size 512, 1024, or 2048 characters F orm.
C-5 Appendix Carbon Black P/N 102796 OCR F abric Nylon, 1" X 60 yards spool-to-spool; Metal reverses on each end. NOTE : Use only ribbons that meet the stated specifications. Cleaning Interval 3 months or 250 hours of operation Kit P/N 132009 includes a plastic cleaning nozzle, soft-bristled brush, and cleaning instructions.
Appendix C-6.
D-1 Appendix APPENDIX D CONTROL CODE CROS S REFERENCE The following lists provide the programming control codes alphabetically by function and alphabetically by code. In the Programming chapter, an alphabetical list of control code functions is presented by functional groups (format, paper motion, graphics, etc.
Appendix D-2 Alphabetical By Function (continued) Function P-Series Serial Page Emphasized P rint R eset SFCC F ESC F 6-36 Expanded (Double W ide) P rint SFCC W ESC W 6-37 SFCC k Expanded (Double W id.
D-3 Appendix Alphabetical By Function (continued) Function P-Series Serial Page Superscript/Subscript P rinting SFCC S ESC S 6-67 Superscript/Subscript P rinting R eset SFCC T ESC T 6-68 Underline SFC.
Appendix D-4 Alphabetical By P-Series Code (continued) P-Series Code Function P age SFCC 7 Character Set Select (Control Codes) 6-22 SFCC h Elongated (Double High) P rint 6-34 SFCC A Line Spacing n/72.
D-5 Appendix Alphabetical By Serial Matrix Code (continued) Serial Code Function P age ESC 0 Line Spacing 1/8 Inch (8 lpi) 6-49 ESC 1 Line Spacing 7/72 Inch 6-51 ESC 2 Line Spacing 1/6 Inch (6 lpi) 6-.
Appendix D-6.
E-1 Appendix APPENDIX E DOWNLOADING CHARACTERS Introduction P9012 printers include the ability to create and download unique characters from the host com Ć puter to the printer's working memory (R AM). Downloaded characters must be reloaded each time printer power is recycled or RAM is cleared unless they are saved into nonvolatile memory.
Appendix E-2 {A}; is the single-character attribute flag identifying whether the character contains descenders (a portion of the character descends below the botĆ tom of the print line) or extenders (2 dot rows near the bottom of the character are repeated until what would be the next line boundary at 6 lpi).
E-3 Appendix T able E-2. Calculating the Character Size Print Mode Bits P er Dot Column Number of Dot Columns HS10 HS12 HS13 DP10 DP12 DP13 DP15 DP17 NLQ10 NLQ12 NLQ15 OCR-A OCR-B Code* (dpi) Dots per.
Appendix E-4 Examples The following examples illustrate the process of creating three characters: one with no attribĆ utes, one with descenders, and one with extenders. NOTE: If adjacent dots are used to create the character , the printer will set an adjacent dot flag, and any line containing the character may print at half the normal speed.
E-5 Appendix The command for the character shown in Figure E-1 is defined as follows: ESC c {60}{57E}{0};{0;F00;1080;2041;2046;2048;2050;10E0;F00;0;0;0;} where: ESC c is the Serial Matrix Control Code Header introducing the Download a Character command.
Appendix E-6 Example 2: Characters with Descenders 1 3 4 5 6 7 8 9 10 11 12 2 LSB 1 2 3 4 5 6 7 8 9 F F F F F F F FF F 1 7 6 5 4 3 2 1 0 F Selected Print Mode and Pitch: DP 10 cpi DP 10 cpi with desce.
E-7 Appendix { 90E } is the address location in the Character Library where the downloaded character will be sent. The existing character at address 90 will be reĆ placed with the new character. E is the decimal field terminator (required after each decimal field).
Appendix E-8 Example 3: Characters with Extenders 1 3 4 5 6 7 8 9 10 11 12 2 LSB 1 2 3 4 5 6 F F F 5 4 3 2 1 0 Selected Print Mode and Pitch: HS 10 cpi HS 10 cpi with extenders = 12 Columns x 6 bits p.
E-9 Appendix { 1010E } is the address location in the Character Library where the downloaded character will be sent. A ddress 1010 is an unused address.
Appendix E-10.
F-1 Appendix APPENDIX F HARDW ARE JUMPER CONFIGURA TION Jumpers on the DCU (Data Control Unit) board are used to select a few configuration paĆ rameters. These jumpers are installed for normal operation at the factory. However, certain applications may require a modification to the jumper configuration.
Appendix F-2 Side P anel Removal T o remove the right side panel to access the card cage, perform the following instructions and refer to Figure F-1. 1.
F-3 Appendix Removing the DCU PCBA After removing the side panel, the card cage can be accessed. T o remove the DCU PCBA from the card cage, perform the following instructions and refer to Figure F-2.
Appendix F-4 Figure F-2. R emoving the DCU PCBA.
Index – 1 INDEX A Alternate T erminating R esistors, 7-5 A SCII Character Chart, A-1 A ttribute Set and R eset Codes, 6-3 B Backspace, 6-7 Bell, 6-8 Bit Image Graphics Density, 4-3 Plotting, 4-1, 4-.
Index – 2 Control Code Header, 6-2 Cross R eference, 6-4, D-1 Control P anel 6/8 LPI Switch, 2-4 Alphanumeric Message Display, 2-2 CHECK Indicator, 2-4 CLEAR Switch, 2-4 Configuration Diagrams, 3-7 .
Index – 3 G Graphics Bit Image, 4-1 Bit Image Plotting, 4-1, 4-2 Combining with T ext, 4-12 P-Series High Density, 6-55 P-Series Normal Density, 6-56 Serial Matrix, 4-1 Single Density Bit Image Samp.
Index – 4 NVFU (continued) End L oad Code, 5-11 LPI Byte, 5-10 Memory Clearing, 5-12 R elative Line Slewing, 5-13 Start L oad Code, 5-10 Using, 5-12 O OCR-A, 10-2, B-20 OCR-B, 10-2, B-22 Odd Dot Plo.
Index – 5 Print, 1-4, C-2 R emoval DCU PCBA, F-3 Shipping R estraints, 11-3 Side P anel, F-2 R eplacing the Ribbon, 2-14 R equirements P ower, 11-1 Site, 11-2 R eset, P rinter, 2-18, 6-57 R esisters.
Index – 6 V V ertical F ormat Units CVFU, 5-13 D VFU, 5-6 EVFU, 5-2 NVFU, 5-10 V ertical F ormatting, Serial Matrix, 5-17 V ertical T abs V ertical T abs, 6-71 V ertical T ab Set/Clear, 6-72 V ertic.
.
P RINTRONIX 17500 C ARTWRIGHT R OAD P . O . B OX 19559 I RVINE, CA . 92713-9559 P HONE: 714/863-1900 F AX: 714/660-8682 P RINTRONIX N EDERLAND BV P . O . B OX 163, N IEUWEWEG 283 NL-6600 A D W IJCHEN T HE N ETHERLANDS P HONE: (31) 8894-90111 F AX: (31) 246-419768 P RINTRONIX A .
Ein wichtiger Punkt beim Kauf des Geräts Printronix P9000 Series (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Printronix P9000 Series noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Printronix P9000 Series - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Printronix P9000 Series reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Printronix P9000 Series erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Printronix P9000 Series besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Printronix P9000 Series verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Printronix P9000 Series. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Printronix P9000 Series gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
