Benutzeranleitung / Produktwartung 185143 des Produzenten Poulan
Zur Seite of 32
OWNER'S MANUAL MODEL NUMBER: P8527ESA SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away 185143 Rev 1 01.25.08 B Y/TH Printed in U.S.A. WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions.
2 Safe Operation Practices for Snow Throwers IMPORT ANT : This machine is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury or death. SAFETY RULES WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 PRODUCT SPECIFICA TIONS Gasoline Capacity 4.0 Quarts and T ype: Unleaded Regular only Oil T ype SAE 30 (above 40°F) (API-SF-SJ): SAE 5W -30 or 10W -30 (0° to +40°F) SAE 0W -30 (below 0°F) Oil Capacity: 22 Ounces Spark Plug: Champion RN4C (Gap: .
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON MAINTENANCE ..................................................... 14-15 MAINTENANCE SCHEDULE ..................................... 14 SERVICE AND AD JUST MENTS ........................... 16-18 STORAGE ........
5 AS SEMBL Y / PRE-OPERA TION Read these instructions and this man u al in its entirety before you attempt to assemble or operate your new snow thrower . Y our new snow thrower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping purposes.
6 AS SEMBL Y / PRE-OPERA TION INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.
7 AS SEMBL Y / PRE-OPERA TION INST ALL WEIGHT BAG (See Fig. 10) Though seldom required, the weight bag will re duce the ten den cy of the auger housing to ride up on hard, icy drifts. Should conditions require it, install as follows: 1. Shut off engine and wait for all moving parts to stop.
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING Y OUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow throwers conform to the standards of the American National Standards Institute. FIG. 11 OPERA TION LH and RH turn triggers - used to steer the snow thrower . Drive speed control lever - used to select forward or reverse motion and speed of snow thrower .
10 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just - ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles.
11 OPERA TION TO THROW SNOW (See Fig. 16) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow .
12 ENGINE OIL FILL CAP / DIPSTICK FUEL SHUT - OFF VAL VE PRIM ER SAFETY IG NI TION KEY THROT TLE CHOKE CONTROL ST ARTER BUTTON RECOIL ST ARTER HANDLE GAS O LINE FILLER CAP NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL L OCA TION. ACTUAL L OCA TION MA Y VARY WITH ENGINE ON Y OUR UNIT .
13 COLD ST ART - ELECTRIC ST ARTER 1. Insert safety ignition key into the ignition slot until it clicks. DO NOT turn the key . Keep the extra safety ignition key in a safe place. 2. Place throttle control in F AST position. 3. Rotate choke control to FULL position.
14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
15 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual).
16 SERVICE AND ADJUSTMENTS WARNING: T o avoid serious injury , before performing any service or ad- just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped.
17 SERVICE AND ADJUSTMENTS TO REPL ACE BEL TS (See Fig. 23) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear , they should be replaced. It is recommended that the belt(s) be replaced by a qualified service center .
18 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance.
19 Does not start 1. F uel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position.
20 REP AIR P AR TS SNOW THROWER - MODEL NUMBER P8527ESA AUGER HOUSING / IMPELLER ASSEMBL Y 6 6 5 6 6 9 12 2 1 3 7 7 8 6 11 28 27 27 19 30 26 25 24 23 22 18 21 20 19 28 19 31 25 24 26 23 29 21 21 19 20.
21 KEY P ART NO . NO. DESCRIPTION 1 183578 Bag, Weight 2 183577 Bracket, Weight Bag 3 74520524 Screw , Hex Head 5/16-18 x 1-1/2 4 181083 Pulley , Impeller 5 175323 Bearing Assembly , Flange 6 155377 N.
22 REP AIR P AR TS SNOW THROWER - MODEL NUMBER P8527ESA CONTROL P ANEL / DISCHARGE CHUTE 3 2 1 1 2 6 7 4 5 6 16 18 17 10 11 14 3 13 15 8 8 9 12 19 2 2 21 21 22 23 14 26 28 27 27 25 20 29 24 22 23.
23 REP AIR P AR TS SNOW THROWER - MODEL NUMBER P8527ESA CONTROL P ANEL / DISCHARGE CHUTE KEY P ART NO . NO. DESCRIPTION 1 183334 Knob, Lever 2 17501010 Screw #10-24 x 5/8 3 178674 Control Assembly , D.
24 REP AIR P AR TS SNOW THROWER - MODEL NUMBER P8527ESA HANDLES 5 11 12 15 7 10 33 18 19 37 34 35 20 20 21 21 6 11 5 36 13 2 5 15 11 4 4 3 3 16 17 16 23 22 38 39 24 27 26 24 25 27 40 22 17 1 4 4 14 5 .
25 KEY P ART NO . NO. DESCRIPTION 1 178875X479 Lever , Auger Control, RH 2 178648X479 Lever , T raction Drive Control, LH 3 179439 Nut, Cage 1/4-20 4 178888 Bushing, Flange 5 169675 Retainer , Hairpin.
26 REP AIR P AR TS SNOW THROWER - MODEL NUMBER P8527ESA DRIVE 35 33 15 41 22 34 29 22 31 26 7 2 43 2 11 3 3 25 24 23 12 32 27 44 20 21 21 22 16 1 17 15 2 4 13 1 1 2 5 3 1 2 5 3 3 5 1 2 3 13 1 5 2 7 8 .
27 KEY P ART NO . NO. DESCRIPTION 1 146315 Screw , Hex Head 5/16-18 x 3/4 2 73800500 Nut, Lock 5/16-18 3 155415 W asher , Flat 4 17490508 Screw , Hex Head 5/16-18 x 1/2 5 180017 Bearing, Flange 6 1801.
28 REP AIR P AR TS SNOW THROWER - MODEL NUMBER P8527ESA CHAS SIS / ENGINE / PULLEYS 10 21 6 19 17 10 21 22 23 2 1 3 4 6 7 8 9 12 13 15 27 10 25 24 18 7 6 20 14 28 6 30 29 31 31 47 48 46 40 44 10 11 49.
29 REP AIR P AR TS SNOW THROWER - MODEL NUMBER P8527ESA CHAS SIS / ENGINE / PULLEYS KEY P ART NO . NO. DESCRIPTION 1 181044 Spring, T raction Idler 2 180522 Pulley , Idler (2-1/4) 3 - - - Engine, T ec.
30 REP AIR P AR TS SNOW THROWER - MODEL NUMBER P8527ESA WHEELS / DECALS 10 31 32 30 15 18 17 19 10 12 1 2 7 4 3 4 13 20 11 21 33 22 23 24 10 10 25 26 28 27 29 28 29 11 11 27 26 28 23 22 33 20 11 14 9 .
31 REP AIR P AR TS SNOW THROWER - MODEL NUMBER P8527ESA WHEELS / DECALS KEY P ART NO . NO. DESCRIPTION 1 178834 Wheel Assembly (16" Power Steer) 2 155443 Pin, Klik 1/4 3 181843 Cover , Power Stee.
giving the complete mfg. ID#, serial number and date of purchase of your product and the name and address of the authorized dealer from whom it was purchased. THIS WARRANTY DOES NOT APPL Y TO INCIDENT AL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WAR RAN TIES ARE LIMITED TO THE SAME TIME PERIODS ST A TED HEREIN FOR OUR EXPRES SED WAR- RAN TIES.
Ein wichtiger Punkt beim Kauf des Geräts Poulan 185143 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Poulan 185143 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Poulan 185143 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Poulan 185143 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Poulan 185143 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Poulan 185143 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Poulan 185143 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Poulan 185143. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Poulan 185143 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
