Benutzeranleitung / Produktwartung PP5600 SERIES des Produzenten POSIFLEX Business Machines
Zur Seite of 26
Rev.: Original PP5600 SERIES POS PRINTER USER’S MANUAL Never attempt to repair th is product yourself. Improper repair work can be dangerous. Do not connect cables in ways other than those mentioned in this manual. Different connections may cause equipment damage and burning.
P/N: 19380900010 Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
i Table Of Contents BEFORE STARTED . . . . . . . . . . . . . . . . . . . . . . . 1 -- 1 CONGRATULATION . . . . . . . . . . . . . . . . . . . . . . 1 -- 1 PRODUCT BRIEFING . . . . . . . . . . . . . . . . . . . . . 1 -- 1 Descriptions . . . . . . . . . .
ii Printing problems . . . . . . . . . . . . . . . . . . . . . 3 -- 2 Paper jam problems . . . . . . . . . . . . . . . . . . . 3 -- 3 Auto cutter problems . . . . . . . . . . . . . . . . . . 3 -- 3 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . .
1 - 1 I. BEFORE STARTED A. CONGRATULATION You have made a very wise decision by purchasing the easy loading; high performance; high reliability 9 pin dot matrix impact printer Aura PP5600 series of Posiflex products. This series of printers has been elegantly designed for a Point - Of - Sale, kitchen & kiosk application.
1 - 2 It even supports some enhancement capability for reminder function to persons around. It can be used to drive a separately purchased kitchen bell for such reminder function in noisy environment. This printer also supports application in dif ferent countries of various kinds of power systems by changing the power cord to the power adaptor.
1 - 3 • Supports Posiflex kitchen bell drive when used as kitchen printer • Hardware hand shaking in serial interface through DIP switch selection • Manual paper cut mechanism for PP5600D or guillotine type auto cutter plus manual cut mechanism for PP5600B • Supports ES C command • Dimension: 228 mm (l) x 158 mm (w) x 140 mm (h) C.
1 - 4 Length of the interface cable depends on whether the order includes the power adaptor. When power adaptor is included, the interface cable is 6 ft long for stand alone application. When the power adaptor is not included in the order, the interface cable is a shorter one for integrated application in Posifle x POS system.
1 - 5 F. IMPORTANT TIPS Never attempt to disassemble or modify this product. Unauthorized interior access voids product warranty. Do not set any liquid or drinks such as coffee on the printer case. Do not touch the print head after printing. It can become very hot.
1 - 6 G. MAIN PARTS ON THE EXTERIOR Pa rallel Connector Serial Connector Power Connector Peripheral Connector Frame G round Rear View Screws Setup Window Window Plate Screw Bottom View Manual Cutter B.
1 - 7 Indicators • Power LED: green • Error LED: red • Paper Out LED: red Interior View Auto Cutter Ribbon Cassette Area Paper Guide Roller Paper Roll Area Lift Tab.
.
2 - 1 II. QUICK START - UP A. CONNECTING CABLES 1. Serial connection All the external connectors are in the recessed area at the rear bottom. The serial connector is a 9 pin D sub Female connector at the right in the picture above. Apply the male connector of RS232 cable to this port f or serial application.
2 - 2 When the printer is used as a kitchen printer, please use this port for kitchen b ell connection instead. 4. Power connection The power connector is a 3 pin jack between the peripheral connector and the parallel connector.
2 - 3 turning the ribbon feed knob of the ribbon cartridge counterclockwise. The ribbon m ust be properly tightened to be able to set in position in installation. Never turn the knob the other way round or the ribbon may mess up inside the cassette and ruin the whole cassette.
2 - 4 bracket of the print mechanism as in the picture. • Close the top cover by fitting its rear end lug first for ribbon replacement only or go on loadin g paper as in next paragraph. C. LOADING PAPER 1. Drop the paper roll inside the paper compartment in the orientation as shown in left picture below.
2 - 5 D. SELF TEST Press and hold down the feed button while turning on the power. The printer will then perform a self test and print out some major settings detec ted. You may turn off the power and turn it on again to resume normal use of the printer at this stage.
2 - 6 E. SPECIAL ADJUSTMENTS 1. Paper near end sensor If the paper near end sensor is installed in the printer and enabled, a fine tuning on the po sition of the paper near end sensor may be required for different outer diameter of the paper roll bobbin.
2 - 7 clearance will vary. This clearance can be observed from the offset pattern printed in bottom of self test. Whenever the lower part of the long vertical lines is shifted horizontally away from the upper part by about one dot width, the offset value should be adjusted to move i t back for decent print if bi - directional print is engaged.
.
3 - 1 III. MAINTENANCE GUIDES A. MAINTENAN CE GUIDE LINES B. GENERAL CLEANING Please use a soft hair brush or compressed air to clear away any dust or paper scraps accumulation inside the printer. Check also the area of the auto - cutter regularly. C.
3 - 2 2. Printing Problems Nothing can be printed with ERROR LED ON – Check the Paper Out LED. If it is ON, most probably the paper roll is not installed or is at or near the end. Install a new paper roll. If the Paper Out LED is OFF, please check for paper jam described in next item.
3 - 3 3. Paper Jam Problems Paper is jammed inside the printer – Please follow procedures below. • Turn off the printer. • Open the top cover after the print head c ools down. • Cut the paper roll from the paper intake slot with a pair of scissors.
3 - 4 To check for home position of the auto cutter, please open the auto cutter and look into the blade slot and the sp indle hole as in pictures below. Use proper tool to cut away the paper around auto cutter if it presents obstacle to the actions. Clear away any paper scraps from the auto cutter once it is reset to position.
4 - 1 IV. SPECIFICATIONS A. PRINTER ITEM SPECIFICATION Printing method Dot m atrix impact method Print head configuration 9 pins Printing direction Bi - directional; logic seeking Effective printing width 59.
4 - 2 C. RIBBON CASSETTE ITEM REQUIREMENT RECOMMENDED TYPE RC200P COLO R Purple RIBBON MATERIAL Nylon 66 RIBBON WIDTH 13 mm CASSETTE DIMENSION 144.4 (W) x 65 (D) x 26.7 (H) mm EXPECTED LIFE 3 million characters D. POWER ADAPTOR ITEM REQUIREMENT INPUT VOLTAGE 100 V AC ~ 250 V AC INPUT FREQUENCY 50 ~ 60 HZ INPUT CURRENT 1.
Ein wichtiger Punkt beim Kauf des Geräts POSIFLEX Business Machines PP5600 SERIES (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie POSIFLEX Business Machines PP5600 SERIES noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für POSIFLEX Business Machines PP5600 SERIES - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von POSIFLEX Business Machines PP5600 SERIES reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über POSIFLEX Business Machines PP5600 SERIES erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon POSIFLEX Business Machines PP5600 SERIES besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von POSIFLEX Business Machines PP5600 SERIES verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit POSIFLEX Business Machines PP5600 SERIES. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei POSIFLEX Business Machines PP5600 SERIES gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
