Benutzeranleitung / Produktwartung 8931 des Produzenten Porter-Cable
Zur Seite of 23
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No.
2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage.
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm.
4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6 1. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ...................
8 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section.
9 FOREWORD Porter-Cable routers are designed for continuous, rugged operation to handle the most demanding production applications. NOTE: This tool is shipped completely assembled. No assembly time or tools are required. SELECTING THE BIT The 891 series of routers accommodates bits with 1/4“ and 1/2“ diameter shanks.
10 INST ALLING AND REMOVING THE BIT USING SPINDLE LOCK ACTUA TOR (892) 1. Turn the router upside down on its motor cap. 2 . Push down and rotate the spindle lock actuator (A) Fig. 3 into place. 3. Open the clamp (B) Fig. 4. 4 . Press the lever (C) Fig.
11 1. Loosen the sub-base mounting screws (C) Fig. 7 just enough to allow the sub-base (D) to move. 2. Open the clamp (A) Fig. 7, and adjust the power unit so that the collet nut (B) engages the center hole in the sub-base (D). Allow the sub-base to center itself on the collet nut.
12 8931 PLUNGE BASE INST ALLING AND REMOVING THE BIT 1. Stand the router upside down on its motor cap (Fig. 8B). 2. Clean and insert the shank of the bit into the collet until the shank bottoms. Then back it out approximately 1/16". 3. Press the spindle lock button (A) Fig.
13 ADJUSTING THE PLUNGE BASE Disconnect tool from power source . 1. Loosen the depth rod locking knob (A) Fig. 11, and depth indicator knob (C) Fig. 11, allowing the depth rod (D) Fig. 11 to contact one of the turret stops (A) Fig. 12. Normally the deepest desired cut is set with the depth rod resting on the base casting (B) Fig.
14 2. Release the plunge mechanism by pulling the locking lever (A) Fig. 14 down. Lower the plunge mechanism until the router bit touches the work surface. Release the lever and push it to the right to lock the mechanism in this position. 3. Tighten the depth-rod locking knob (A) Fig.
15 OPERA TION CONNECTING TO POWER SOURCE Before connecting the tool to the power source, CHECK TO SEE THAT THE SWITCH IS IN THE “OFF” POSITION . Also, check the power circuit to see that it is the same as that shown on specification plate of the tool.
16 ST ARTING AND STOPPING THE MOTOR Before starting the tool, clear the work area of all foreign objects. Also keep a firm grip on the tool to resist starting torque.
17 Avoid “Climb-Cutting” (cutting in direction opposite that shown in Fig. 22). “Climb-Cutting” increases the chance for loss of control resulting in possible injury. When “Climb- Cutting” is required (backing around a corner), exercise extreme caution to maintain control of router.
18 1. Use a 5/16" hex wrench to loosen the screw in the handle (A) Fig. 25. Remove the handle from the router base. Place the handle and screw aside for use later if needed. 2. Remove the plastic plug from the dust port (2) Fig. 24. 3. Remove the screws (B) Fig.
19 USING THE MUL TI-FUNCTION CASE The case for your router has been designed to provide protection when transporting the router to the job site, and to make the router easier to use in the workshop. STORAGE AND TRANSPORTATION The case provides storage for the collet wrench at (A) Fig.
20 USING A ROUTER ACCESSORY TABLE The router can be mounted to a router accessory table (not included). For instructions on how to mount the router to the router accessory table, refer to the accessory table instruction manual. You can attach the inverted back half of the case to a workbench with screws through the holes (H) Fig.
21 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.
22 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase.
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.
Ein wichtiger Punkt beim Kauf des Geräts Porter-Cable 8931 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Porter-Cable 8931 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Porter-Cable 8931 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Porter-Cable 8931 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Porter-Cable 8931 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Porter-Cable 8931 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Porter-Cable 8931 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Porter-Cable 8931. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Porter-Cable 8931 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
