Benutzeranleitung / Produktwartung 38129 des Produzenten Porter-Cable
Zur Seite of 23
ESP AÑOL: PÁGINA 23 FRANÇAISE : P AGE 43 Double Insulated 1 0" Bench T op T able Saw Instruction Manual Part No. 912933 - 09-15-03 The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence.
2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
3 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT .
4 ADDITIONAL SAFETY RULES FOR T ABLE SA WS 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this machine.
5 FOREWORD The Porter -Cable Model 3812 is a 10" Bench T op T able Saw . The saw comes with a 26"x20" table surface with a rip fence extension wing which provides a 24½" rip capacity for ripping 4x8 sheets.
6 CAR TON CONTENTS Fig. 2 1 2 3 4 5 6 7 8 9 1. Saw 2. Fence 3. T able Insert 4. Blade Guard and Spreader Assembly 5. Blade Wrench (2) 6. Miter Gauge 7.
7 ASSEMBL Y BLADE RAISING AND LOWERING HANDWHEEL Insert the 1-3/4" screw (D) Fig. 4, thr ough handle (E). Assemble handle (E) to handwheel (A) by threading screw (D) clockwise into handwheel as shown in Fig. 5. Handle (E) should rotate fr eely on screw (D).
8 6. NOTE: The anchor block (B) Fig. 6, has been adjusted at the factory so that the spreader will be aligned with the saw blade which is supplied with the saw . When changing to blades with dif ferent widths it may be necessary to adjust the anchor block (B) Fig.
9 RIP FENCE TO SA W T ABLE 1. The rip fence may be used on the right or left hand side of the saw table. Lift locking handle (A) Fig. 12, and position the front end of the fence on the fr ont fence rail as shown.
10 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING SA W The “ON/OFF” switch (A) Fig 16, is located on the front of the saw cabinet. T o tur n the saw “ON” pull the “ON/OFF” switch (A) out. T o tur n the saw “OFF”, push in on the “ON/OFF” switch (A).
11 ADJUSTING 0 AND 45 DEGREE POSITIVE STOPS Y our saw is equipped with positive stops for rapid and accurate positioning of the saw blade at 0 and 45 degrees to the table. This saw has the capability to go 2 degrees beyond 0 and 45 degr ees (-2º to 47º).
12 RIPPING THIN STOCK T o adjust the fence, pull up on lever (B) so that the top of the rip fence can be removed, and r epositioned on the rip fence as shown in Fig. 25. This is only necessary when the fence guide rails are extended. When using the guide rails for ripping, the fence must be positioned as shown in Fig.
13 MITER GAGE OPERA TION AND ADJUSTMENTS When straight cross-cutting (blade set 90 degr ees to the table) the miter gage can be used in either table slot. When bevel cross-cutting (blade tilted) only use the miter gage in the right table slot where the blade is tilted away from the miter gage and your hands.
14 Cross-cutting r equires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig.
15 If the ripped work is less than 4 inches wide, a PUSH STICK should always be used to complete the feed, as shown in Fig. 35. The PUSH STICK can easily be made from scrap material as explained in the section “CONSTRUCTING PUSH STICK.
16 The dado head set (D) Fig. 40, is assembled to the saw arbor as shown. IMPORT ANT : The blade guard and splitter assembly cannot be used when dadoing and must be removed. Auxiliary jigs, fixtur es, push sticks and feather boards should also be used.
MAINTENANCE CHANGING THE BLADE 1. DISCONNECT MACHINE FROM POWER SOURCE. USE ONL Y 10" DIAMETER SAW BLADES RA TED FOR 4600 RPM OR HIGHER WITH 5/8" ARBOR HOLES. 2. Remove the table insert (A) Fig. 44, and raise the saw blade to its maximum height.
18 SERVICE AND REP AIRS All quality tools will eventually requir e servicing or replacement of parts due to wear fr om normal use. These operations, including brush inspection and replacement, should ONL Y be performed by either an AUTHORIZED PORTER-CABLE SERVICE ST A TION or a POR TER-CABLE • DEL T A F ACTOR Y SERVICE CENTER.
19 19 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT.
20 NOTES.
21 NOTES.
22 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase.
The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S.
Ein wichtiger Punkt beim Kauf des Geräts Porter-Cable 38129 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Porter-Cable 38129 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Porter-Cable 38129 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Porter-Cable 38129 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Porter-Cable 38129 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Porter-Cable 38129 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Porter-Cable 38129 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Porter-Cable 38129. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Porter-Cable 38129 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
