Benutzeranleitung / Produktwartung 3802 des Produzenten Porter-Cable
Zur Seite of 21
ESP AÑOL: PÁGINA 21 FRANÇAISE : P AGE 41 12" Compound Miter Saw Instruction Manual Part No. 900988 - 11-30-00 The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence.
IMPORT ANT SAFETY INSTRUCTIONS SA VE THESE INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS. This tool was designed for certain applications.DO NOT modify or use it for any application other than for which it was designed.
3 25. WARNING: SOME DUST CREA TED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer , birth defects or other repr oductive harm.
4 4 REPLACEMENT P AR TS When servicing, use only identical replacement parts. POLARIZED PLUGS: T o r educe the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way .
UNP ACKING 1. Car efully remove the machine fr om the carton. Retain all packing materials until you have inspected and satisfactorily operated the machine. WARNING: Do not connect the machine to the power source until you have r ead and understood this entire instruction manual.
6 6 MOVING T ABLE TO THE 0 DEGREE CUT -OFF POSITION 1. Rotate locking knob (A) Fig. 6, counter -clockwise as far as it will go to unlock. Depr ess lever (B) and rotate table (C) to the 0 degree straight cut-of f position, release lever (B) and tighten locking knob (A).
7 7 3. Use a straight edge (C) Fig. 7C, to make the extension table (B) even with saw table (D), and tighten the two screws (A) Fig. 7B. 4. Attach the fence slide support (E) Fig. 7D, to the extension table (B) by using the two 1 1/4” long hex head screws, 5/16” lockwashers and 5/16” flat washers (F).
9. Position lock handle (M) Fig. 7J, on stud and replace scr ew and spring (L) that were removed in STEP 7 . NOTE: Lock handle (M) is spring-loaded and can be repositioned by lifting up on handle. A TT ACHING DUST BAG Depress spring clips (A) Fig. 8, of dust bag (B) and clip dust bag (B) onto end of dust chute.
9 9 DANGER: A TURNING SAW BLADE CAN BE DANGEROUS. AFTER COMPLETING CUT , RELEASE SWITCH TRIGGER (A) FIG. 12, TO ACTIV A TE BLADE BRAKE. KEEP CUTTINGHEAD DOWN UNTIL BLADE HAS COME TO A COMPLETE STOP . WARNING: THE TORQUE DEVELOPED DURING BRAKING MA Y LOOSEN THE ARBOR SCREW .
10 10 T o adjust the sliding fit between the movable table and the base, turn nut (A) Fig. 14, clockwise to increase the sliding fit (opposite to decrease the fit). This adjustment should not be so tight that it restricts the r otating movement of the table, or so loose that it affects the accuracy of the saw .
11 11 A TT ACHING OPTIONAL WORK CLAMP The work clamp is an important accessory . After purchase, the work clamp can be attached to any one of the four holes (A) Fig. 18, provided on the base of the machine, (three of which ar e shown). 1. Thread lock knob (B) Fig.
12 1. The cuttinghead of your compound miter saw can be tilted to cut any bevel angle from a 90 degr ee straight cut-off to a 45 degr ee left bevel angle by loosening bevel lock handle (A) Fig. 23, tilting cuttinghead (B) to the desired angle, and tightening lock handle (A).
13 13 ADJUSTING 0 AND 45 DEGREE BEVEL POSITIVE STOPS 1. DISCONNECT THE SAW FROM THE POWER SOURCE. 2. Adjust saw so that both bevel and miter pointers are set at 0 degrees. Tighten bevel lock handle and lock cuttinghead in down position. 3. Place one end of a square (A) Fig.
14 14 Correct adjustment pr ovides for a good snug sliding fit between these two parts. This adjustment should not be so tight that it restricts the tilting movement of the trunnion (A) when bevel cutting, or so loose that it af fects the accuracy of the saw cut.
15 15 TYPICAL OPERA TIONS AND HELPFUL HINTS 1. Before cutting, make certain the cutting arm and table area ar e at their correct settings and firmly locked in place. 2. Before cutting, determine that the workpiece is the right size for the saw . 3. Place the workpiece on the table and hold or clamp it firmly against the fence.
16 16 CUTTING BOWED MA TERIAL 1. When cutting flat pieces, first check to see if the material is bowed. If it is, make sure the material is positioned on the table as shown in Fig. 39. 2. If the material is positioned the wrong way , as shown in Fig. 40, the workpiece will pinch the blade near the completion of the cut.
17 17 CUTTING CROWN MOULDING One of the many features of the saw is the ease of cutting crown moulding. The following is an example of cutting both inside and outside corners on 52/38 degree wall angle crown moulding.
18 18 MAINTENANCE CHANGING THE BLADE WARNING: USE ONL Y CROSS-CUTTING SAW BLADES. DO NOT USE BLADES WITH DEEP GULLETS AS THEY CAN DEFLECT AND CONT ACT GUARD 1. Use only 12" diameter blades with 1" arbor holes that are rated for 4200 RPM or higher .
19 19 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING BRUSHES, DISCONNECT THE MACHINE FROM THE POWER SOURCE. Brush life varies, depends on the load on the motor . Check the brushes after the first 50 hours of use of a new machine, or after a new set of brushes has been installed.
20 20 NOTES.
The following are trademarks of POR TER-CABLE Corporation (Las siguientes son marcas registradas de POR TER-CABLE S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE Corpor.
Ein wichtiger Punkt beim Kauf des Geräts Porter-Cable 3802 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Porter-Cable 3802 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Porter-Cable 3802 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Porter-Cable 3802 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Porter-Cable 3802 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Porter-Cable 3802 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Porter-Cable 3802 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Porter-Cable 3802. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Porter-Cable 3802 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
